Caple CM116 Manual

CM116
Ca
p
le Microwave oven and
g
rill
Caple Microwave oven and grill
Technical information

Item Part Code Description Qty
A00 251500100244 Cavity Ass'y 1
A01 252100100016 Mica plate 1
B01 261501409903 base plate 1
B02 251302000013 oven foot 4
B03 251502501540 Bottom hinge Ass'y 1
C01 251300201809 Control panel 1
C02 261505802200 Decorate on Control panel 1
C07 251306003205 Button of open door 1
C08 252010100001 button spring for open door 1
C10 251301600141 Knob 1
C14 251304900055 Display 1
C18 261400116830 PCB 1
C20
251301900386
button
1
CM116 - Caple Microwave oven and grill
C20
251301900386
button
1
C28 261516900406 Decorate on button 1
C35 261400600003 Control PCB 1
D01 251500200124 Door Ass'y 1
D02 256300500035 Latch 1
D03 252010000012 Latch spring 1
D04 251502401799 Top hinge Ass'y 1
D07 261300122204 Door frame 1
D08 256300600076 Door seal 1
D09 261505802503 Decorate for doo
r
1
E01 251200100068 Magnetron 1
E02 251202701048 THERMOSTAT 1
E04+E21 251202701535 Wire 95mm 2
E05 251200200355 H.V transforme
r
1
E06 251200701304 H.V Capacity 1
E07 251200900861 H.V diode 1
E10 256400301380 Filte
r
1
E11 261201200030 fuse 1
E13 263600500006 Lamp 1
C43 261503202100 Metal wave guide 1
E16 256201000454 Power cord 1
E28 261203300180 H.V fuse 1
E29 261201300640 THERMOSTAT 70/95 level terminal 1
E36 261201300850 THERMOSTAT 180/145 vertical terminal 1
G02 251200400025 Quarz heate
r
2
G06
261501000300
Holder of Quarz heater
1
G06
261501000300
Holder
of
Quarz
heater
1
L01 261301301500 Interlock holde
r
1
L02 261301101000 Interlock leve
r
1
T01 251200300001 Turntable moto
r
1

Item Part Code Description Qty
CM116 - Caple Microwave oven and grill
T02 252200100008 Couple
r
1
T03 262200200007 Ring 1
T04 252100500013 turntable 1
W01 261300800100 fan holde
r
1
W02 251300900015 fan 1
W03 261200600350 Fan moto
r
1
Z01 261501500300 Holder H.V.C 1
Z24 261502606813 Cove
r
1
-261511705802 Grill rack 1

Installation Instruction
Please Read the Manual Carefully Before Installation
Please Note
Electrical connection
The oven is fitted with a plug and must be only connected to a properly installed earthed
socket. In accordance with the appropriate regulations, the socket must only be installed and
the connecting cable must only be replaced by a qualified electrician.
If the plug is no longer accessible following installation and all-pole isolating switch must
be present on the installation side with a contact gap at least 3mm.
A. Built-in furniture
The built-in cabinet shall not have a rear wall behind the appliance.
Minimum installation height is 85cm.
Do not cover ventilation slots and air intake points.

B. Prepare the Cabinet.
1. Read the instruction on the BOTTOM CABINET TEMPLATE, put the
template on the bottom plane of cabinet.
2. Make marks on the bottom plane of cabinet according to marks “a” of the
template.
2
1

3. Remove the BOTTOM CABINET TEMPLATE, and fix the BOTTOM
BRACKETS with SCREW A.
C. Prepare the oven.
4
3
4. Fix SCREW B on the UPPER AIR TUNNEL of the oven.

D. Install the oven.
5. Install the oven into the cabinet.
zAdjust the height of SCREW B to keep 1mm gap between the SCREW B
and the top plane of cabinet.
zMake sure that the OVEN FEET are aligned with the grooves of brackets
when install the oven into the cabinet.
zDo not trap or kink the power cord.
6. Open the door; fix the oven to the cabinet with SCREW C at the
INSTALLATION HOLE of TRIM KIT.
5
6

SAFETY PRECAUTIONS
This device is to be serviced only by properly qualified service personnel.
Consult the service manual for proper service procedures to assure continued safety operation and for precautions to
be taken to avoid possible exposure to excessive microwave energy.
PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
A) Do not operate or allow the oven to be operated with the door open.
B) Make the following safety checks on all ovens to be serviced before activating the magnetron or other
microwave source, and make repairs as necessary; (1) interlock operation, (2) proper door closing, (3)
seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and
latches, (5) evidence of dropping or abuse.
C) Before turning on microwave power for any service test or inspection within the microwave generating
compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment,
integrity, and connections.
D) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation
and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual
before the oven is released to the owner.
E) A microwave leakage check should be performed on each oven prior to release to the owner.
CAUTION
MICROWAVE RADIATION
DO NOT BECOME EXPOSED TO RADIATION FROM THE MICROWAVE GENERATOR
OR OTHER PARTS CONDUCTING MICROWAVE ENERGY.