Carl Valentin Vita II series User manual

Copyright by Carl Valentin GmbH / 7948005A.1118
Information on the scope of delivery, appearance, performance,
dimensions and weight reflect our knowledge at the time of printing.
We reserve the rights to make modifications.
All rights, including those regarding the translation, are reserved.
No part of this document may be reproduced in any form (print,
photocopy or any other method) or edited, copied or distributed
electronically without written permission from Carl Valentin GmbH.
Due to the constant further development of our devices discrepancies
between manual and device can occur.
Please check www.carl-valentin.de for the latest update.
Trademarks
All named brands or trademarks are registered brands or registered
trademarks of their respective owners and may not be separately
labelled. It must not be concluded from the missing labelling that it is
not a registered brand or a registered trademark.
Carl Valentin label printers comply with the following safety guidelines:
CE
EG Low-Voltage Directive (2006/95/EC)
EG Electromagnetic Compatibility Directive (2004/108/EC)
Carl Valentin GmbH
Postfach 3744
78026 Villingen-Schwenningen
Neckarstraße 78 –86 u. 94
78056 Villingen-Schwenningen
Phone
Fax
[phone]
[phone]
E-Mail
Internet
[e-mail]
www.carl-valentin.de

Vita II
Table of contents
11.18
Operating manual
3
Table of contents
Table of contents.............................................................................. 3
1Introduction............................................................................ 5
1.1 General Instructions ................................................................ 5
1.2 Intended Use........................................................................... 5
1.3 Important Notes....................................................................... 6
1.4 Connector Pin Assignment (Printer Rear)............................... 7
2Safety notes........................................................................... 9
2.1 Warnings ..........................Fehler! Textmarke nicht definiert.
2.2 Operating conditions.............................................................. 10
3Technical data...................................................................... 15
3.1 Control inputs and outputs .................................................... 18
4Installation............................................................................ 23
4.1 Setting up the label printer .................................................... 23
4.2 Connecting the label printer .................................................. 24
4.3 Switching the label printer on and off.................................... 24
4.4 Initiation of the label printer ................................................... 25
5Loading media..................................................................... 27
5.1 Loading media....................................................................... 27
5.2 Loading fanfold labels ........................................................... 31
5.3 Loading transfer ribbon ......................................................... 32
6Function menu..................................................................... 35
6.1 Operation panel..................................................................... 35
6.2 Menu structure....................................................................... 36
6.3 Print settings.......................................................................... 40
6.4 Label layout........................................................................... 41
6.5 Device settings...................................................................... 43
6.6 Network ................................................................................. 46
6.7 Password............................................................................... 46
6.8 Interface................................................................................. 48
6.9 Emulation............................................................................... 49
6.10 Date & Time........................................................................... 50
6.11 Service functions................................................................... 51
6.12 Main menu............................................................................. 55
7Options................................................................................. 57
7.1 Cutter..................................................................................... 57
7.2 Dispenser I/O......................................................................... 59
7.3 WLAN.................................................................................... 63
7.4 Scanner ................................................................................. 64
8Compact Flash Card / USB Memory Stick ........................ 67
8.1 General Information............................................................... 67
8.2 Display Structure................................................................... 67
8.3 Navigation.............................................................................. 68
8.4 Define User Directory............................................................ 69
8.5 Load Layout........................................................................... 70
8.6 File Explorer .......................................................................... 71
8.7 Firmware Update................................................................... 76
8.8Filter....................................................................................... 76

Table of contents
Vita II
4
Operating manual
11.18
9Maintenance and cleaning.................................................. 77
9.1 General cleaning ................................................................... 78
9.2 Cleaning the Transfer Ribbon Drawing Roller....................... 78
9.3 Cleaning the printer roller...................................................... 79
9.4 Cleaning the printhead .......................................................... 80
9.5 Cleaning the label photocell .................................................. 81
9.6 Replacing the printhead (general)......................................... 82
9.7 Replacing the printhead ........................................................ 83
9.8 Adjusting the printhead.......................................................... 85
10 Error correction ................................................................... 87
11 Additional information........................................................ 93
11.1 Column printing ..................................................................... 93
11.2 Hotstart.................................................................................. 94
11.3 Backfeed/Delay ..................................................................... 96
11.4 Photocells.............................................................................. 98
11.5 Ultrasonic photocell (option).................................................. 99
12 Environmentally-Friendly Disposal ................................. 101
13 Index ................................................................................... 103

Vita II
Introduction
11.18
Operating manual
5
1 Introduction
1.1 General Instructions
Basic information and warning references with the corresponding
signal words for the danger level are as follows specified in this
manual:
DANGER identifies an extraordinarily great and immediate
danger which could lead to serious injury or even death.
WARNING identifies a possible danger would could lead
to serious bodily injury or even death if sufficient
precautions are not taken.
WARNING of cutting injuries.
Pay attention that cutting injuries caused by blades, cutting
devices or sharp-edged parts are avoided.
WARNING of hand injuries.
Pay attention that hand injuries caused by closing
mechanical parts of a machine/equipment are avoided.
WARNING of hot surfaces.
Pay attention so as not to come into contact with hot
surfaces.
CAUTION indicates a potentially dangerous situation
which could lead to moderate or light bodily injury or
damage to property.
NOTICE gives you tips. They make a working sequence
easier or draw attention to important working processes.
Gives you tips on protecting the environment.

Handling instruction

Optional accessories, special fittings
Datum
Information in the display
1.2 Intended Use
The label printer is a state-of-the-art device which complies with the
recognized safety-related rules and regulations. Despite this, a danger
to life and limb of the user or third parties could arise and the label
printer or other property could be damaged while operating the device.

Table of contents
Vita II
6
Operating manual
11.18
The label printer may only be used while in proper working order and
for the intended purpose. Users must be safe, aware of potential
dangers and must comply with the operating instructions. Faults, in
particular those which affect safety, must be remedied immediately.
The label printer is solely intended to print suitable media which have
been approved by the manufacturer. Any other or additional use is not
intended. The manufacturer/supplier is not liable for damage resulting
from misuse. Any misuse is at your own risk.
Intended used includes heeding the operating manual, including the
maintenance recommendations/regulations specified by the
manufacturer.
NOTICE!
The complete documentation is included in the scope of
delivery on CD ROM and can also currently be found in the
internet.
1.3 Important Notes
The label printer can be used in thermal as well as in thermal transfer
applications.
The label printer is equipped with 8 vector, 6 bitmap and 6
proportional fonts. It can be printed inverse, in italic format or 90
degrees turned fonts.
The handling of our durable label printers is easy and comfortable.
The parameter settings are made with the keys of the foil keyboard. At
each time the graphic display shows the current status.
By the use of a 32 Bit processor and a large main memory of 16MB
also for large labels (6000 mm) a fast print is possible.
An enormously high print quality is obtained by most modern
printhead technology.
By a new-developed electronics a maximum print speed of up to
200 mm/s can be achieved.
Time-saving firmware update is possible by interface. As default, the
print module is equipped with a parallel, serial, USB and Ethernet
interface. Additionally, the print module is equipped with an USB Host
that permits the connection of an external USB keyboard and/or an
USB memory stick. The print module automatically recognizes by
which interface it is controlled.
The label printer is delivered with a printer driver and the free label
software Labelstar Office LITE. Existing labels can be saved to a CF
card or an USB stick, opened and/or modified with a PC keyboard and
finally stand-alone printed.

Vita II
Introduction
11.18
Operating manual
7
1.4 Connector Pin Assignment (Printer Rear)
E
B
F
G
H
D
J
I
C
A
1
2
Figure 1
A
Power supply
B
Plug-in for CF card
C
Winder connection
CAUTION!
The label printer can be damaged by non-compliant
winders.
Attach only winders of Carl Valentin.
D
USB interface
E
Serial interface RS-232
F
Ethernet 10/100 interface
G
USB host for USB keyboard and USB memory stick
H
Parallel interface
I
External output/input (option)
J
Switch On/Off
1 - LED orange
1 - Lighting = Connection active
1 - Flashing = Data transfer
1 - Off = No connection
2 - LED green
2 - Lighting: Speed 100 MBit
2 - Off: Speed 10 MBit

Vita II
Safety notes
11.18
Operating manual
9
2 Safety notes
The printer is designed for power supply systems from 110 … 230 V.
Connect the label printer only to electrical outlets with a ground
contact.
Couple the label printer to devices using extra low voltage only.
Before making or undoing connections, switch off all devices involved
(computer, printer, accessories etc.).
Operate the label printer in a dry environment only and do not get it
wet (sprayed water, mist etc.).
Maintenance and servicing work can only be carried out by trained
personnel.
Operating personnel must be trained by the operator on the basis of
the operating manual.
If the label printer is operated with the cover open, ensure that
clothing, hair, jewellery and similar personal items do not contact the
exposed rotating parts.
The print unit and parts of it (e.g. printhead) can get hot during
printing. Do not touch the printhead during operation. Cool down the
print unit before changing material, removal or adjustment.
Never use highly inflammable consumables.
Carry out only the actions described in these operating instructions.
Any work beyond this may only be performed by the manufacturer or
upon agreement with the manufacturer.
Unauthorized interference with electronic modules or their software
can cause malfunctions.
Other unauthorized work or modifications to the direct print module
can endanger operational safety.
Always have service work done in a qualified workshop, where the
personnel have the technical knowledge and tools required to do the
necessary work.
There are warning stickers on the direct print modules that draw your
attention to dangers. Therefore the warning stickers are not to be
removed as then you and others cannot be aware of dangers and may
be injured.
DANGER!
Danger to life and limb from power supply!
Do not open the casing.

Safety notes
Vita II
10
Operating manual
11.18
2.1 Operating conditions
Before initial operation and during operation these operating
conditions have to be observed to guarantee save and interference-
free service of our printers.
Therefore please carefully read these operating conditions.
Shipment and storage of our printers are only allowed in original
packing.
Installation and initial operation of printer is only allowed if operating
conditions were fulfilled.
Initial operation, programming, operation, cleaning and service of our
printers are only recommended after careful study of our manuals.
Operation of printer is only allowed by especially trained persons.
NOTICE!
Perform trainings regularly.
Content of the training are chapter 2.1 (Operating conditions),
chapter 5 (Loading media) and chapter 9 (Maintenance and
cleaning).
These indications are also valid for someone else's equipment
supplied by us.
Only use original spare and exchange parts.
Please contact the manufacturer with respect to spare/wear parts.
The installation place of printer should be even, free of vibration and
currents of air are to be avoided.
The printers have to be installed to ensure optimal operation and
servicing.
The installation of the power supply to connect our printers has to be
effected according to the international rules and regulations,
especially the recommendations of one of the three following
commissions:
International Electronic Commission (IEC)
European Committee for Electro technical Standardisation
(CENELEC)
Verband Deutscher Elektrotechniker (VDE)
Our printers are constructed according to VDE and have to be
connected to a grounded conductor. The power supply has to be
equipped with a grounded conductor to eliminate internal interfering
voltage.
Conditions for
installation place
Installation of
power supply

Vita II
Safety notes
11.18
Operating manual
11
Power line voltage and power line frequency: See type plate
Allowable tolerance of power line voltage:
+6% …−10% of nominal value
Allowable tolerance of power line frequency:
+2% …−2% of nominal value
Allowable distortion factor of power line voltage: <=5%
In case your net is infected (e.g. by using thyristor controlled
machines) anti-interference measures have to be taken. You can use
one of the following possibilities:
Provide separate power supply to our printers.
In case of problems please connect capacity-decoupled isolation
transformer or similar interference suppressor in front of our
printers.
Emitted interference according to EN 61000-6-3: 2007
industrial sector
Interference voltage to wires according to EN 55022: 09-2003
Interference field power according to EN 55022: 09-2003
System perturbation according to EN 61000-3-2: 09-2006
Flicker according to EN 61000-3-3: 1955 + A1:2001 + A2:2005
Immunity to interference according to EN 61000-6-2: 2005
industrial sector
Stray radiation against discharge of static electricity according to
EN 61000-4-2: 12-2001
Electromagnetic fields according to EN 61000-4-3: 11-2003,
ENV 50204: 03-1995
Fast transient burst according to EN 61000-4-4: 07-2005
Surge according to EN 61000-4-5: 12-2001
High-frequency tension according to EN 61000-4-6: 12-2001
Voltage interruption and voltage drop according to EN 61000-4-
11: 02-2005
NOTICE!
This is a machine of type A. This machine can cause
interferences in residential areas; in this case it can be required
from operator to accomplish appropriate measures and be
responsible for it.
Technical data of
power supply
Anti-Interference
measures:
Stray radiation and
immunity from
disturbance

Safety notes
Vita II
12
Operating manual
11.18
All connecting lines have to be guided in shielded lines. Shielding has
to be connected on both sides to the corner shell.
It is not allowed to guide lines parallel to power lines. If a parallel
guiding cannot be avoided a distance of at least 0.5 m has to be
observed.
Temperature of lines between: −15 …+80 °C.
It is only allowed to connect devices which fulfil the request 'Safety
Extra Low Voltage' (SELV). These are generally devices which are
checked corresponding to EN 60950.
The data cables must be completely protected and provide with metal
or metallised connector housings. Shielded cables and connectors are
necessary, in order to avoid radiant emittance and receipt of electrical
disturbances.
Shielded line:
4 x 2 x 0,14 mm² ( 4 x 2 x AWG 26)
6 x 2 x 0,14 mm² ( 6 x 2 x AWG 26)
12 x 2 x 0,14 mm² (12 x 2 x AWG 26)
Sending and receiving lines have to be twisted in pairs.
Maximum line length:
with interface V 24 (RS-232C) - 3 m (with shielding)
with parallel interface - 3 m (with shielding)
with USB - 3 m
with Ethernet - 100 m
To avoid inadmissible heating, free air convection has to be ensured.
Protection according IP: 20
Ambient temperature °C (operation): Min. +5 Max. +35
Ambient temperature °C (storage): Min. −20 Max. +60
Relative air humidity % (operation): Max. 80
Relative air humidity % (storage): Max. 80
(bedewing of printers not allowed)
Connecting lines to
external machines
Installation of
data lines
Allowable lines
Air convection
Limit values

Vita II
Safety notes
11.18
Operating manual
13
We do not take any responsibility for damage caused by:
Ignoring our operating conditions and operating manual.
Incorrect electric installation of environment.
Building alterations of our printers.
Incorrect programming and operation.
Not performed data protection.
Using of not original spare parts and accessories.
Natural wear and tear.
When (re)installing or programming our printers please control the
new settings by test running and test printing. Herewith you avoid
faulty results, reports and evaluation.
Only specially trained staff is allowed to operate the printers.
Control the correct handling of our products and repeat training.
We do not guarantee that all features described in this manual exist in
all models. Caused by our efforts to continue further development and
improvement, technical data might change without notice.
By further developments or regulations of the country illustrations and
examples shown in the manual can be different from the delivered
model.
Please pay attention to the information about admissible print media
and the notes to the printer maintenance, in order to avoid damages
or premature wear.
We endeavoured to write this manual in an understandable form to
give and you as much as possible information. If you have any queries
or if you discover errors, please inform us to give us the possibility to
correct and improve our manual.
Guarantee

Vita II
Technical data
11.18
Operating manual
15
3 Technical data
Printhead
Vita II
103/8 T
Vita II
104/8
Vita II
106/12
Vita II
106/24
Vita II
108/12 T
Print resolution
203 dpi
203 dpi
300 dpi
600 dpi
300 dpi
Max. print speed
200 mm/s
200 mm/s
150 mm/s
100 mm/s
150 mm/s
Print width
104 mm
104 mm
105,7 mm
105,7 mm
108,4 mm
Passage width
Standard
116 mm
116 mm
116 mm
116 mm
116 mm
Cutter mode
112 mm
112 mm
112 mm
112 mm
112 mm
Printhead
Flat Type1
Flat Type2
Flat Type2
Flat Type2
Flat Type1
Labels
Labels, continuous rolls
or fan-fold
paper, cardboard, textile, synthetics
Max. material weight
220 g/m² (larger on demand)
Min. label width
12 mm
Min. label height
standard: 5 mm
cutter/dispenser mode: 15 mm
Max. label height
6000 mm
6000 mm
3000 mm
1000 mm
3000 mm
Max. roll diameter
internal unwinder: 180 mm
internal rewinder: --
Core diameter
40 mm / 75 mm (option)
Winding
outside or inside
Label sensor
transmission and reflexion from bottom
Transfer ribbon
Ink
outside or inside
Max. roll diameter
Ø 80 mm
Core diameter
25,4 mm / 1″
Max. ribbon length
300 m
Max. width
110 mm
Dimensions (mm)
Width x height x depth
236 x 238 x 374
Weight
11 kg
Electronics
Processor
High Speed 32 Bit
RAM
16 MB
Slot
for Compact Flash card Type I
Battery cache
for Real-Time clock (storage of data with shut-down)
Warning signal
acoustic signal when error
Interfaces
Serial
RS-232C (up to 115200 Baud)
Parallel
SPP
USB
2.0 High Speed Slave
Ethernet
10/100 Base T, LPD, RawIP-Printing, DHCP, HTTP, FTP
2 x USB Master
connection for external USB keyboard and memory stick
WLAN (option)
module 802.11 b/g/n WEP, WPA, WPA-PSK, WPA2, WPA2-PSK,
EAP
Operation data
Power supply
110 … 230 V / 50 … 60 Hz
Max. power consumption
275 VA
Nominal current
2.5 A
Operating temperature
5 … 35 °C
Humidity
max. 80% (non-condensing)
1for thermal direct
2for thermal transfer

Technical data
Vita II
16
Operating manual
11.18
Operation panel
Vita II
103/8 T
Vita II
104/8
Vita II
106/12
Vita II
106/24
Vita II
108/12 T
Keys
test print, function menu, quantity, CF Card,
feed, enter, 4 x cursor
LCD display
graphic display 132 x 64 pixel
Settings
date, time, shift times
11 language settings (others on demand)
label and device parameters, interfaces,
password protection, variables
Monitoring
Stop printing if
end of ribbon / end of labels / printhead open
Status report
extensive status print with information about settings e.g. print length
counter, runtime counter, photocell interface
and network parameters
printout of all internal fonts and all supported bar codes
Fonts
Font types
6 Bitmap fonts
8 Vector fonts/TrueType fonts
6 proportional fonts
other fonts on demand
Character sets
Windows 1250 up to1257, DOS 437, 850, 852, 857, UTF-8
all West and East European Latin, Cyrillic, Greek
and Arabic (option) characters are supported
other character sets on demand
Bitmap fonts
size in width and height 0,8 … 5,6
zoom 2 … 9
orientation 0°, 90°, 180°, 270°
Vector fonts/TrueType
fonts
size in width and height 1 … 99 mm
variable zoom
orientation 0°, 90°, 180°, 270°
Font attributes
depending on character font
bold, Italic, Inverse, Vertical
Font width
variable
Bar codes
1D bar codes
CODABAR, Code 128, Code 2/5 interleaved, Code 39, Code 39
extended, Code 93, EAN 13, EAN 8, EAN ADD ON, GS1-128,
Identcode, ITF 14, Leitcode, Pharmacode, PZN 7 Code, PZN 8 Code,
UPC-A, UPC-E
2D bar codes
Aztec Code, CODABLOCK F, DataMatrix, GS1 DataMatrix,
MAXICODE, PDF 417, QR Code
Composite bar codes
GS1 DataBar Expanded, GS1 DataBar Limited, GS1 DataBar
Omnidirectional, GS1 DataBar Stacked, GS1 DataBar Stacked
Omnidirectional, GS1 DataBar Truncated
all bar codes are variable in height, module width and ratio. orientation
0°, 90 °, 180°, 270°.
Optionally with check digit and human readable line.
Software
Configuration
ConfigTool
Process control
NiceLabel
Label software
Labelstar Office Lite, Labelstar Office
Windows driver
Windows 7®32/64 Bit, Windows 8®32/64 Bit
Windows 8.1®32/64 Bit, Windows 10®32/64 Bit
Windows Server 2008®(R2) 64 Bit
Windows Server 2012®64 Bit, Windows Server 2012®(R2) 64 Bit

Vita II
Technical data
11.18
Operating manual
17
Tear-off edge
Real time clock with printout date and time
Automatic daylight saving time
Storage of data with shut-down
Variables: link field, counter, date/time, currency and shift
variable, CF data
Integrated unwinder
(max. outer diameter 180 mm
Thermal and thermal transfer version
USB host for connection of an external USB keyboard and an
USB memory stick
Ethernet interface
CVPL protocol and ZPL II® protocol
Label photocell
(transmission and reflexion from below)
Slot for CF card
Windows printer driver on CD ROM
Labelstar Office Lite on CD ROM
Cutting unit
Dispensing unit with photocell
Dispensing unit without photocell
Ultrasonic photocell
External rewinder for labels
External rewinder for backing paper
Unwinder
WLAN interface
Dispenser I/O
Standard equipment
Optional equipment

Technical data
Vita II
18
Operating manual
11.18
3.1 Control inputs and outputs
By means of a maximum of 16 control inputs and outputs which, in the
following, are also referred to as ports, different functions of the printer
system can be triggered and operating states can be displayed.
The ports are provided by means of a D-Sub bushing (26pin HD) at
the rear panel of the printer system and are galvanically isolated from
protective earth (PE) by means of an optocoupler semi-conductor
route.
Each port can be configured as input and as output. This function
however, is predefined in the printer software and cannot be changed
by the user.
The following parameters can be changed and set by using the menu:
debounce times and high or low active.
Figure 2
Printer, internal
circuitry

Vita II
Technical data
11.18
Operating manual
19
Figure 3
Port 1 to Port 16 = Assignment for I/O Profile Std_Label
Identification
Pin
Description / Function
Port 1
10
Print start and cut (Input)
Port 2
1
Reprint last printed label (Input)
Port 3
11
Counter Reset (Input)
Port 4
2
Option applicator only:
Start application (Input)
Port 5
12
Error reset (Input)
Port 6
3
Cancel all print jobs (Input)
Port 7
13
No function
Port 8
4
No function
Port 9
15
Error (Output)
Port 10
6
Print order activ (Output)
Port 11
16
Dispenser photocell:
Label exists at dispenser photocell (Output)
Port 12
7
Single print (Output)
Port 13
17
Ready (Output)
Port 14
8
Option applicator only:
Ready for application (Output)
Port 15
18
Option scanner only
Bar code not readable (Output)
Port 16
9
Prior warning for transfer ribbon end (Output)
COM/VDC
for Inputs
19
Common reference potential of all control inputs. 'COM/VDC for
Inputs' is usually connected with the (-) terminal of the control voltage
and the control inputs are switched to active (+).
By means of the option '2nd LED', 'COM/VDC for Inputs' can
optionally be connected with the (+) terminal of the control voltage.
Then, the control inputs are switched to active (-).
VDC for
Outputs
20
Common supply connection of all control outputs. 'VDC for Outputs'
must be connected with the (+) terminal of the control voltage.
Never leave 'VDC for Outputs' open even if no output is used.
COM for
Outputs
5,14
21,22
Common reference potential of all control outputs. 'COM for Outputs'
must be connected with the (-) terminal of the control voltage.
Never leave 'COM for Outputs' open even if no output is used.
GND-PE
23,24
'GND-PE' is the reference potential of the '+5 VDC EXT' and '+24
VDC EXT' voltages provided by the printer system.
'GND-PE' is printer internally connected with protective earth (PE).
Configuration of
D-Sub socket

Technical data
Vita II
20
Operating manual
11.18
Identification
Pin
Description / Function
+ 5 VDC
EXT
25
5 Volt DC output for external use. Max. 1 A.
This voltage is provided from direct print module and can be used e.g. as
control voltage. Never apply any external voltage to this output.
+ 24 VDC
EXT
26
24 Volt DC output for external use. Max. 1 A.
This voltage is provided from direct print module and can be used e.g. as
control voltage. Never apply any external voltage to this output.
Plug Connector
Type
D-Sub connector High Density
26-pin. / connector
Manufacturer
W+P-Products
Reference number
110-26-2-1-20
Output Voltages (connected with GND-PE)
+ 24 V / 1 A
Fuse: Polyswitch / 30 V / 1 A
+ 5 V / 1 A
Fuse: Polyswitch / 30 V / 1 A
Port 1 - 15
Input
Tension
5 VDC … 24 VDC
Impedance
47Ω + (100nF || 10 kΩ)
Output
Tension
5 VDC … 24 VDC
Impedance
47Ω + (100nF || 10 kΩ || 47Ω)
Current max.
High +15 mA
Low -15 mA
Port 16
Input
Tension
5 VDC … 24 VDC
Impedance
100nF || 10 kΩ
Output
Tension
5 VDC … 24 VDC
Impedance
100nF || 10 kΩ
Current max.
High +500 mA (Darlington BCP56-16)
Low - 500 mA (Darlington BCP56-16)
Optocoupler
Output
TCMT4106, CTR 100% - 300%, Vishay or
TLP281-4(GB), CTR 100% - 600%, Toshiba
Input
TCMT4106, CTR 100% - 300%, Vishay or
TLP281-4(GB), CTR 100% - 600%, Toshiba
Input
Option 2nd LED
TCMT4600, CTR 80% - 300%, Vishay or
TLP280-4, CTR 33% - 300%, Toshiba
Technical data