Carrier 38YCC Series Operation manual

Copyright 1997 Carrier Corporation Form 38YCC-C1PD
Product
Data
38YCC 50 Hz
Heat Pump
Sizes 024 thru 060
The 38YCC 50 Hertz Outdoor
Sections of Split-System Heat Pumps
aredesignedforquiet, reliableheating
during the winter and cooling during
the summer. With an EER up to 9.2,
these heat pump systems provide
economy of operation through energy
conservation when used with
components designated by Carrier.
They recover heat for indoor comfort
from outdoor air during the heating
season and, by automatically
reversing the refrigerant system,
remove indoor heat and excess
humidity during the cooling season.
FEATURES/BENEFITS
ElectricalRange — Unitsareoffered
in single phase 230v 50 Hz. Three-
phase units are available in sizes 036,
048, and 060 in 400v 50 Hz.
Size Range — The 38YCC is
available in nominal sizes 024, 036,
048 and 060 to meet the needs of
residential and light commercial
applications.
Compressor — Designed
specifically for heat pump duty, with
energy efficiency during heating and
cooling operation. The compressor is
hermetically sealed against
contamination to assure long life and
dependable performance, internally
sprung (units with reciprocating
compressor) and externally mounted
onrubberisolatorsforquietoperation.
Continuous compressor operation is
approved down to –30
° F (–34.4 ° C)
in the heating mode, and down to
55
° F (12.8 ° C) in the cooling mode.
(See heating and cooling performance
tables.)

2
Built-in-Reliable Components —
Include a suction-tube accumulator
that reduces the amount of liquid
refrigerant that reaches the
compressor; low-pressure switch to
stop the compressor if refrigerant
charge is lost; crankcase heater on
units with reciprocating compressor
and all 3-phase units to keep
compressor oil warm and free of
refrigerant for maximum lubricity;
internal compressor relief valve for
high-pressure protection.
DischargeSilencer — Minimizes low
frequency sound and pressure
pulsation generated by compressor
discharge gas.
Defrost Control Board —
Incorporates a defrost relay, defrost
timer, and low-voltage terminations.
The defrost control is a time and
temperature initiation/termination
control which includes 3 field-
selectable time periods of 30, 50, and
90 minutes. The control includes built-
in 5-minute compressor delay for units
equipped with scroll compressors.
Weather-ProtectiveCabinet —Steel
is protected with a heavy galvanized
coating and treated with a layer of zinc
phosphate. A coat of modified
polyester powder coating is then
applied and baked-on, providing each
unitwith ahard, smoothfinish thatwill
last for many years.
All screws on cabinet exterior are
coated for a long-lasting rust-resistant,
quality appearance.
Unit Design — All units are equipped
with totally enclosed fan motors for
greater reliability under rain and snow
conditions. The large, wraparound coil
uses copper tube and enhanced
aluminum fin and is designed for
optimum heat transfer during heating
and cooling. Vertical air discharge
carriessound andairup andawayfrom
adjacent patio areas and foliage. Coils
can be cleaned with a common garden
hose.
External Service Valves — Both
service valves are brass, front seating
type. Valves are externally located
so refrigerant tube connections can
be made quickly and easily. Each
valve has a service port for ease of
checking operating refrigerant
pressures. The 38YCC has sweat-type
field connections.
Safety — All units are designed and
manufactured in accordance with
UnderwritersLaboratories(U.L.1995)
standard for safety, heating and
cooling equipment.
Model number nomenclature
38YCC 024
Electric Heat Pump
Nominal Capacity
024 — 24,000 Btuh (7.0 Kw) 048 — 48,000 Btuh (14.1 Kw)
036 — 36,000 Btuh (10.6 Kw) 060 — 60,000 Btuh (17.6 Kw)
703
Packaging
Series
Electrical
7 — 230-1-50
9 — 400-3-50
Quality Assurance

3
Physical data
* Tube sizes are for lengths up to 50 ft (15.24m). For lengths over 50 ft (15.24m), consult Residential Split System Long-Line Application Guideline.
NOTE: See unit Installation Instructions for proper installation.
METERING DEVICE
*Piston listed is for any approved coil combination.
UNIT SIZE-SERIES 024-70 036-70, 90 048-70, 90, 92 060-90, 92
OPERATING WT (Lb/Kg)
140 / 63.6 216 / 97.8 216, 216, 224 / 97.8, 97.8, 101.8 257, 259 / 116.4, 117.5
COMPRESSOR
Manufacturer
Type
Copeland
Recip Copeland Recip Millennium, Millennium, Copeland Scroll Millennium, Copeland Scroll
REFRIGERANT
Control
Charge (Lb/Kg) @ 15 ft (4.57m)
R-22
Piston
4.84 / 2.20 7.93 / 3.60 5.32, 5.32, 7.25 / 2.41, 2.41, 3.29 10.95, 10.75 / 4.97, 4.88
CONDENSER FAN Propeller Type, Direct Drive
Air Discharge Vertical
Air Qty (CFM / L/S) 2160 / 1019 2750 / 1298 2750 / 1298 2750 / 1298
Motor HP 1/10 1/4 1/4 1/4
Motor RPM (50 Hz) 850 900 900 900
CONDENSER COIL
Face Area (Sq ft/m
2
) 12.4 / 1.15 22.4 / 2.08 18.7 / 1.74 18.7 / 1.74
Fins per In. / Fins per Cm 20 / 8 20 / 8 20 / 8 20 / 8
Rows 1112
Circuits 2346
CONNECTION (In./mm ID)
Vapor
Liquid
Sweat
5/8 / 15.875 3/4 / 19.05 7/8 / 22.225 7/8 / 22.225
3/8 / 9.525
REFRIG TUBES* (In./mm OD)
Vapor (0–50 Ft (15.24m)
Tube Length)
5/8 / 15.875 3/4 / 19.05 7/8 / 22.225 1-1/8 / 28.575
Vapor (Max Diameter for
Long-Line Applications)
3/4 / 19.05 7/8 / 22.225 1-1/18 / 28.575
Liquid (0–50 Ft (15.24m) Tube
Tube Length)
3/8 / 9.525
Liquid (For Long-Line
Applications)
3/8 / 9.525
UNIT
SIZE-SERIES OUTDOOR PISTON INDOOR PISTON*
024-70 49 63
036-70, 90 61 73
048-70, 90 73 88
048-92 73 90
060-90 76 98
060-92 76 96

4
Accessories
* Isolation relay required.
† Consult low-ambient controller Installation Instructions for application.
‡ Hard shutoff TXV requires compressor start assist on reciprocating compressors.
N/A — Not applicable in this application.
ORDERING NUMBER DESCRIPTION
KAATD0101TDR
Time-Delay Relay — All Sizes
P251-0083 (RCD)* Low-Ambient Controller — All Sizes
P504-8083S (RCD) Filter Drier — Bi-Flow — Sizes 024, 036
P504-8163S (RCD) Filter Drier — Bi-Flow — Sizes 048, 060
32LT660004 (RCD) MotorMaster® Control — Sizes 024 (70), 036 (70), 048 (70)
32LT660005 (RCD) MotorMaster® Control — Sizes 036 (90), 048 (90, 92), 060 (90, 92)
KAAFT0101AAA † Evaporator Freeze Thermostat — All Sizes
KAAWS0101AAA Winter Start Control — All Sizes
KHAIR0101AAA † Isolation Relay — All Sizes
KSACY0101AAA Cycle Protector — All Sizes
KSAHS1001AAA Start Assist — Capacitor and Relay — Size 024 (70)
KSAHS1301AAA Start Assist — Capacitor and Relay — Size 036 (70)
KSAHS1601AAA Start Assist — Capacitor and Relay — Size 048 (70)
N/A Start Assist — Capacitor and Relay — Sizes 036 (90), 048 (90, 92), 060 (90, 92)
KAACS0201PTC Start Assist — PTC — Sizes 024 (70), 036 (70), 048 (70)
N/A Start Assist — PTC — Sizes 036 (90), 048 (90, 92), and 060 (90, 92)
KSASH1101COP Sound Hood — Sizes 024, 036
KSASH2001CYL Sound Hood — Sizes 048, 060
KHAOT0301FST Outdoor Thermostat — All Sizes
KHAOT0201SEC Secondary Outdoor Thermostat — All Sizes
KHAIC0101AAA Interface Control (Optimizer II®) — All Sizes
KSATX0601HSO‡ TXV (Hard Shutoff) — Sizes 024, 036
KSATX0701HSO‡ TXV (Hard Shutoff) — Sizes 048, 060
KHATX0301RPB TXV (RPB) — Size 024
KHATX0501RPB TXV (RPB) — Sizes 036
KHATX0601RPB TXV (RPB) — Size 048
KHATX0701RPB TXV (RPB) — Size 060
KHAHI0101HPS High-Pressure Switch — All Sizes
KHALS0101LLS Liquid-Line Solenoid Valve (LSV) — All Sizes
P165-0001 (RCD) Unit Risers — All Sizes (2 Required/Unit)
THERMOSTAT DESCRIPTION
TSTATCCNHP01-A
Thermostat, Auto Changeover, Non-Programmable, ° F/ ° C, 2-Stage Heat, 1-Stage Cool
TSTATCCPHP01-A Thermostat, Auto Changeover, 7-Day Programmable, ° F/ ° C, 2-Stage Heat, 1-Stage Cool
TSTATCCPDF01-A
Thermostat Auto Changeover, 7-Day Programmable, ° F/ ° C, Dual Fuel Thermostat
Must be used with Outdoor Sensor (TSTATCCSEN01)
--HH--07AT-215 Thermostat, Manual Changeover, Non-Programmable, ° F, 2-Stage Heat, 1-Stage Cool
TSTATCCSEN01 Outdoor Air Temperature Sensor
TSTATXXNBP01 Backplate for Non-Programmable Thermostat
TSTATXXPBP01 Backplate for Programmable Thermostat
TSTATXXCNV10 Thermostat Conversion Kit (4 to 5 wire) — 10 Pack

5
Accessory usage guideline
* For tubing line sets between 50 and 175 ft (15.24 and 53.34m), refer to Residential Split-System Long-Line Application Guideline.
† For buried line applications, refer to Residential Split System Buried Line Application Guideline.
‡ Only when low-pressure switch is used.
Accessory description and usage (Listed alphabetically)
1. Compressor Start Assist — Capacitor and Relay
Start capacitor and start relay gives “hard” boost to compressor motor at each start-up.
SUGGESTED USE: Installations where interconnecting tube length exceeds 50 ft (15.24m).
Installations where outdoor design temperature exceeds 105 ° F (40.6 ° C).
Replacement installations with hard shutoff expansion valve on indoor coil.
Installations where Liquid-Line Solenoid Valve has been added.
Units installed with Low-Ambient Controller.
2. Compressor Start Assist — PTC
Solid-state electrical device which gives a “soft” boost to compressor motor at each start-up.
SUGGESTED USE: Installations with marginal power supply.
Replacement installations with rapid pressure balance (RPB) expansion valve on indoor coil.
3. Cycle Protector
Solid-state timing device which prevents compressor rapid recycling. Control provides an approximate 5-minute delay after power to the compressor
has been interrupted for any reason, including normal room thermostat cycling.
SUGGESTED USE: Installations in areas where power interruptions are frequent.
Where user is likely to “play” with room thermostat.
All commercial installations.
Installations where interconnecting tube length exceeds 50 ft (15.24m).
High-rise applications.
4. Evaporator Freeze Thermostat
An SPST temperature actuated switch which stops unit operation when evaporator reaches freeze-up conditions.
SUGGESTED USE: All units where Winter Start Control has been added.
All units where Low-Ambient Controller has been added.
5. Filter Drier—Bi-Flow
A device for removing contaminants from refrigerant circulating in a heat pump system: 2-direction flow.
SUGGESTED USE: All split-system heat pumps.
6. High-Pressure Switch
Auto reset SPST switch activated by refrigerant pressure on high side of refrigerant circuit. Cycles compressor off if refrigerant pressure rises to about
426 ± 7 psig and resets at 320 ± 20 psig. Provides protection against compressor damage due to loss of outdoor airflow. To prevent rapid compressor
recycling, Cycle Protector can be used with this switch.
SUGGESTED USE: Installations exposed to very “dirty” outdoor air.
Installations where condenser inlet air temperature exceeds 125 ° F (51.7 ° C).
7. Interface Control (Optimizer II®)
An electric control for controlling a heat pump and gas or oil furnace system for maximum energy savings. It allows heat pump to operate down to a
predetermined economic balance point temperature, then switches to allow furnace operation only below that temperature. Requires outdoor thermostat
to be adjusted for economic balance point temperature.
SUGGESTED USE: All heat pump and gas- or oil-fired furnace combination systems.
8. Isolation Relay
An SPDT relay which switches the Low-Ambient Controller out of the outdoor fan motor circuit when heat pump switches to heating mode.
SUGGESTED USE: All heat pumps where Low-Ambient Controller has been added.
9. Liquid-Line Solenoid Valve (LSV)
An electrically operated shutoff valve to be installed at the outdoor unit and which stops and starts refrigerant liquid flow in response to compressor
operation. Maintains a column of refrigerant liquid ready for action at next compressor operation cycle.
NOTE: Compressor Start Assist–Capacitor and Relay must also be used.
SUGGESTED USE: In certain long-line applications. Refer to Residential Split System Long-Line Application Guideline.
ACCESSORY
REQUIRED FOR
LOW-AMBIENT
APPLICATIONS
(Below 55 ° F/12.8 ° C)
REQUIRED FOR
LONG-LINE
APPLICATIONS*
(Over 50 Ft/15.24m)
REQUIRED FOR
BURIED LINE
APPLICATIONS†
(Over 3 Ft/0.914m)
Crankcase Heater
Yes Yes Yes
Evaporator FreezeThermostat Yes No No
Winter Start Control Yes‡ No No
Accumulator No No Yes
Compressor Start Assist
Capacitor and Relay
Yes Yes Yes
Low Ambient Controller
or
MotorMaster® Control
Yes No No
Wind Baffle See Low-Ambient Instructions No No
Support Feet Recommended No No
Liquid-Line SolenoidValve
or
Hard ShutoffTXV No See Long-Line
Application
Guideline Yes

6
Accessory description and usage (Listed alphabetically) continued
10. Low-Ambient Controller
Head pressure controller is a cycle control device activated by a temperature sensor mounted on a header tube of the outdoor coil. It is designed to cycle
the outdoor fan motor in order to maintain condensing temperature within normal operating limits (approximately 100°F (37.8°C) high and 60°F
(15.6°C) low). The control will maintain working head pressure at low-ambient temperatures down to 0°F (–17.8°C) when property installed.
SUGGESTED USE: Cooling operation at outdoor temperatures below 55°F (12.8°C).
11. MotorMaster® Control
A fan speed control device activated by a temperature sensor. Designed to control condenser fan motor speed in response to the saturated, condensing
temperature during operation in cooling mode only. For outdoor temperatures down to –20°F (–28.9°C), it maintains condensing temperature at
100°F ±10°F (37.8°C ±5.5°C).
SUGGESTED USE: Cooling operation at outdoor temperatures below 55°F (12.8°C).
All commercial installations.
12. Outdoor Air Temperature Sensor
A device that allows the temperature at a remote location (outdoors) to be displayed at the thermostat.
SUGGESTED USE: All corporate programmable thermostats.
13. Outdoor Thermostat
An SPDT temperature actuated switch which turns on supplemental electric heaters when outdoor air temperature drops below set point.
SUGGESTED USE: Heat pump installations with multiple-stage supplemental heaters
14. Secondary Outdoor Thermostat
An SPDT temperature actuated switch which turns on a third stage of supplemental electric heaters when outdoor air temperature drops below the
second-stage set point.
SUGGESTED USE: Heat pump installations where 3-stage operation of supplemental heaters is desired.
15. Sound Hood
Wraparound sound attenuation cover for the compressor. Reduces the sound level by about 2 dBA.
SUGGESTED USE: Unit installed closer than 15 ft (4.55m) to quiet areas—bedrooms, etc.
Unit installed between 2 houses less than 10 ft (3.04m) apart.
16. Thermostatic Expansion Valve (TXV) — Bi-Flow
A modulating flow-control valve which meters refrigerant liquid flow rate into the evaporator in response to the superheat of the refrigerant gas leaving
the evaporator. Kit includes valve, adapter tubes, and external equalizer tube. Both hard shutoff and RPB valves are available.
SUGGESTED USE: For improved system performance in cooling mode for certain combinations of indoor and outdoor units. Refer to ARI Unitary Directory.
Required for use on all zoning systems.
17. Time-Delay Relay
An SPST delay relay which briefly continues operation of the indoor blower motor to provide additional cooling after the compressor cycles off.
SUGGESTED USE: For improved efficiency ratings for certain combinations of indoor and outdoor units. Refer to ARI Unitary Directory.
18. Unit Risers
Six-in. tall plastic rails that are used to elevate outdoor units above mounting pad. The risers are adjustable from 24- to 34-in. long..
SUGGESTED USE: Heat pump installations in light to moderate snowfall areas.
Coastal installations.
Windy areas where debris can circulate.
Rooftop installations.
19. Winter Start Control
An SPST delay relay which bypasses the low-pressure switch for approximately 3 minutes to permit start-up for cooling operation under low-load
conditions.
SUGGESTED USE: All heat pumps where Low-Ambient Controller has been added.

7
Electrical data
* Permissible limits of the voltage range at which unit will operate satisfactorily. Operation outside these limits may result in unit failure.
† Time-delay fuse.
‡ Length shown is as measured 1 way along the wire path between the unit and the service panel for voltage drop not to exceed 2%.
** If wire is applied at ambient greater than 30°C (86°F), consult Table 310-16 of the NEC (ANSI/NFPA 70). The ampacity of nonmetallic-sheathed-
cable (NM), trade name ROMEX, shall be that of 60°C (140°F) conductors, per the NEC (ANSI/NFPA 70) Article 336-30.
If other than uncoated (non-plated), 60°or 75°C (140°or 167°F) insulation, copper wire (solid wire for 10 AWG and smaller, stranded wire for
larger than 10 AWG) is used, consult applicable tables of the NEC (ANSI/NFPA 70).
FLA — Full Load Amps
HACR — Heating, Air Conditioning, Refrigeration
LRA — Locked Rotor Amps
MCA — Minimum Circuit Amps
RLA — Rated Load Amps
NOTE: Control circuit is 24v on all units and requires external power source. Copper wire must be used from disconnect to unit. All motors/compres-
sors contain internal overload protection.
OUTDOOR
UNIT V/PH OPER VOLTS* COMPRESSOR FAN
FLA MCA
MIN WIRE
SIZE**
60°C/75°C
MAX
LENGTH
(Ft)‡
60°C/75°C
MAX
LENGTH
(m)‡
60°C/75°C
MAX FUSE†
OR HACR
TYPE CKT
BKR AMPSMax Min LRA RLA
024-70 230-1 253 207 68.0 11.5 1.4 15.8 14/14 55/39 16.7/11.9 25
036-70 94.0 16.5 1.6 22.2 12/12 65/47 19.8/14.3 35
048-70 140.0 19.2 1.6 25.6 10/10 96/70 29.3/21.3 40
036-90
400-3 440 360
42.0 6.4 0.7 8.7 14/14 260/247 79.2/75.3 15
048-90 66.5 8.0 0.7 10.7 14/14 165/157 50.3/47.9 15
048-92 63.0 7.9 0.7 10.7 14/14 165/157 50.3/47.9 15
060-90 73.0 9.5 0.7 12.6 14/14 165/157 50.3/47.9 20
060-92 74.0 9.0 0.7 11.9 14/14 165/157 50.3/47.9 20

8
AIR DISCHARGE
AIR IN
ASQ
B
P
C
9.5mm DIA
TIEDOWN
KNOCKOUTS
(2) PLACES
73.0mm
31.8mm
H
G
F
E
FIELD CONTROL SUPPLY  CONN 22.2mm DIA 
HOLE
FIELD POWER SUPPLY CONN 22.2mm DIA HOLE WITH  28.6mm DIA KNOCKOUT  AND 34.9mm DIA 
KNOCKOUT
9.5mm DIA LIQUID  LINE CONN
D DIA VAPOR LINE CONN
L
K
J
AIR IN
M
N
AIR DISCHARGE
AIR IN AIR IN
AIR DISCHARGE
NOTES:
1. Allow 762.0 mm clearance to service side of unit, 1219.2 mm above unit, 152.4 mm on one side,

304.8 mm on remaining side, and  609.6 mm between units for proper airflow. 2. Minimum outdoor operating ambient in cooling mode is 13°C  (unless low ambient control is used) max. 52°C. 3. Maximum outdoor operating ambient in heating mode is 19°C. 4. Series designation is the 13th position of the unit model number. 5. Center of gravity .
Dimensions (S.I.)
DIMENSIONS (mm)
UNIT
SIZE SERIES ABCDEFGHJKLMNP
MINIMUM MOUNTING
PAD DIMENSIONS
024 70 571.5 862.0 81.0 15.9 93.6 460.4 501.7 549.3 365.1 479.4 560.4 317.5 304.8 355.6 571.5 x 571.5 036 70, 90 762.0 1014.4 82.6 19.1 165.1 596.9 692.2 739.8 508.0 669.9 750.9 381.0 400.1 393.7 762.0 x 762.0 048 70, 90 762.0 862.0 82.6 22.2 165.1 596.9 692.2 739.8 508.0 669.9 750.9 381.0 400.1 393.7 762.0 x 762.0 048 92 762.0 862.0 82.6 22.2 165.1 596.9 692.2 739.8 508.0 669.9 750.9 387.4 396.9 393.7 762.0 x 762.0 060 90 762.0 862.0 82.6 22.2 165.1 596.9 692.2 739.8 508.0 669.9 750.9 400.1 396.9 381.0 762.0 x 762.0 060 92 762.0 862.0 82.6 22.2 165.1 596.9 692.2 739.8 508.0 669.9 750.9 396.9 400.1 384.2 762.0 x 762.0
A97281

9
Dimensions (English)
A97045
AIR DISCHARGE
AIR IN
ASQ
B
P
C
3/8 -IN. DIA
TIEDOWN
KNOCKOUTS
(2) PLACES
27/8″
11/4″
H
G
F
E
FIELD CONTROL SUPPLY  CONN 7/8 -IN. DIA 
HOLE
FIELD POWER SUPPLY CONN 7/8 -IN. DIA HOLE WITH 
1 1/8 -IN. DIA KNOCKOUT 
AND 1 3/8 -IN. DIA 
KNOCKOUT
3/8 -IN. DIA LIQUID 
LINE CONN
D DIA VAPOR LINE CONN
L
K
J
AIR IN
M
N
AIR DISCHARGE
AIR IN AIR IN
AIR DISCHARGE
NOTES:
1. Allow 30 in. clearance to service side of unit, 48 in. above unit, 6 in. on one side, 12 in.

on remaining side, and 24 in. between units for proper airflow. 2. Minimum outdoor operating ambient in cooling mode is 55°F (unless low ambient control is used) max. 125°F. 3. Maximum outdoor operating ambient in heating mode is 66°F. 4. Series designation is the 13th position of the unit model number. 5. Center of gravity .
DIMENSIONS (IN.)
UNIT
SIZE SERIES ABCDEFGHJKLMNP
MINIMUM MOUNTING
PAD DIMENSIONS
024 70 22-1/2 33-15/16 3-3/16 5/8 3-11/16 18-1/8 19-3/4 21-5/8 14-3/8 18-7/8 22-1/16 12-1/2 12 14 22-1/2 x 22-1/2 036 70, 90 30 39-15/16 3-1/4 3/4 6-1/2 23-1/2 27-1/4 29-1/8 20 26-3/8 29-9/16 15 15-3/4 15-1/2 30 x 30 048 70, 90 30 33-15/16 3-1/4 7/8 6-1/2 23-1/2 27-1/4 29-1/8 20 26-3/8 29-9/16 15 15-3/4 15-1/2 30 x 30 048 92 30 33-15/16 3-1/4 7/8 6-1/2 23-1/2 27-1/4 29-1/8 20 26-3/8 29-9/16 15-1/4 15-5/8 15-1/2 30 x 30 060 90 30 33-15/16 3-1/4 7/8 6-1/2 23-1/2 27-1/4 29-1/8 20 26-3/8 29-9/16 15-3/4 15-5/8 15 30 x 30 060 92 30 33-15/16 3-1/4 7/8 6-1/2 23-1/2 27-1/4 29-1/8 20 26-3/8 29-9/16 15-5/8 15-3/4 15-1/8 30 x 30

10
38YCC BALANCE POINT WORKSHEET
BUILDING HEAT LOSS, KW
UNIT INTEGRATED HEATING CAPACITY, KW
Printed in U.S.A. 11-94
OUTDOOR TEMPERATURE, °C
-20 -10 010 20
30
20
10
40
BASED ON INDOOR ENT. AIR AT 21°C
AND AT RATED CFM
38YCC024 FB4AS024
38YCC036 FB4AS036
38YCC048 FB4AS048
38YCC060 FB4AS060
25
A97280