Carrier 38YCG Series Operation manual

Copyright 2003 Carrier Corporation Form 38YCG-4PD
Product
Data
38YCG (60 Hz)
Heat Pump
Sizes 018 thru 060
The 38YCG Outdoor Section of
Split-System Heat Pumps is designed
for quiet, reliable heating during the
winter and cooling during the summer.
With SEER ratings up to 11.5 and HSPF
from 6.8 to 7.6, this heat pump system
provides economy of operation through
energy conservation when used with
components designated by the
manufacturer. The 38YCG recovers
heat for indoor comfort from outdoor air
during the heating season and, by
automatically reversing the refrigerant
system, removes indoor heat and excess
humidity during the cooling season.
All models are listed with UL (U.S. and
Canada), CEC, and ARI.
FEATURES
Electrical Range — All sizes of the
38YCG are offered in single phase 208–
230v.
Size Range — The 38YCG is available
in 7 nominal sizes from 018 through 060
to meet the needs of residential and light
commercial applications.
Compressor — Designed specifically
for heat pump duty, with energy
efficiency during heating and cooling
operation. Each compressor is
hermetically sealed against
contamination to assure long life and
dependable performance, internally
sprung (units with reciprocating
compressor) and externally mounted on
rubber isolators for quiet operation.
Continuous compressor operation is
approved down to –30°F (–34.4°C)
in the heating mode, and down to 55°F
(12.8°C) in the cooling mode (unless
equipped for low-ambient operation).
(See heating and cooling performance
tables.)

2
Reliable Standard Components —
Includes a suction-tube accumulator that
reduces the amount of liquid refrigerant
that reaches the compressor; a low-
pressure switch to stop the compressor if
refrigerant charge is lost; a crankcase
heater on 036 and 060 sizes to keep
compressor oil warm and free of
refrigerant for maximum lubricity; an
internal compressor relief valve for high-
pressure protection.
Discharge Muffler — Minimizes
low frequency sound and pressure
pulsation generated by compressor
discharge gas.
Defrost Control Board — Incorporates
a defrost relay, defrost timer, and
low-voltage terminations. The defrost
control is a time and temperature
initiation/termination control which
includes 3 field-selectable time periods
of 30, 50, and 90 minutes.
Weather-Protective Cabinet — The
casing steel is protected with a
galvanized coating and treated with a
layer of zinc phosphate. A modified
polyester powder coating is then applied
and baked on, providing each unit with a
hard, smooth finish that will last for
many years.
All screws on cabinet exterior are coated
for a long-lasting, rust-resistant, quality
appearance.
Heavy Duty Inlet Grille —The
WeatherArmor™ coil protector, made of
a coated steel wire grid with vertical 3/8-
in. spacing, is designed to help protect
the coil from inclement weather,
vandalism, and incidental damage. It
provides protection while not restricting
airflow and maintaining ease of coil
inspection and cleaning.
Unit Design — All units are equipped
with totally enclosed fan motors for
greater reliability under adverse weather
conditions. The large, wraparound coil
uses copper tube and enhanced
aluminum fin and is designed for
optimum heat transfer during heating
and cooling. The vertical air discharge
carries the sound and air up and away
from adjacent patio areas and foliage.
Coil can be cleaned with a common
garden hose.
External Service Valves — Both
service valves are brass, front seating
type. Valves are externally located so
refrigerant tube connections can be made
quickly and easily. Each valve has a
service port for ease of checking
operating refrigerant pressures. The
38YCG has sweat field connections.
Additional Standard Features —
Included as standard on this model is
compressor protection through factory-
installed accumulator and low-pressure
switch.
Limited Warranty — Standard 5-year
limited warranty on unit parts and 5-year
limited warranty on compressor.
Model number nomenclature
38YCG 018
Standard 10 SEER Split-System
Heat Pump
Nominal Capacity
018 — 18,000 Btuh 042 — 42,000 Btuh
024 — 24,000 Btuh 048 — 48,000 Btuh
030 — 30,000 Btuh 060 — 60,000 Btuh
036 — 36,000 Btuh
311
Packaging
Series
Electrical
3 — 208-230-1
CERTIFICATION APPLIES ONLY WHEN THE
COMPLETE SYSTEM IS LISTED WITH ARI.
REGISTERED QUALITY SYSTEM
M
A
N
U
F
A
C
T
U
R
E
R
C
E
R
T
I
F
I
E
D
T
O
A
R
I
A
S
C
O
M
P
L
Y
I
N
G
W
I
T
H
A
R
I
S
T
A
N
D
A
R
D
2
1
0
U
N
I
T
A
R
Y
A
I
R
C
O
N
D
I
T
I
O
N
I
N
G
E
Q
U
I
P
M
E
N
T

3
Physical data
* Tube sizes are for lengths up to 50 ft. For lengths over 50 ft and/or 20 ft vertical differential, consult Residential Split-Systems Long-Line Application Guideline.
NOTE: See unit Installation Instructions for proper installation.
METERING DEVICE
*Piston listed is for any approved coil combination.
CHARGING SUBCOOLING (TXV-TYPE EXPANSION DEVICE)
UNIT SIZE 018 024 030 036 042 048 060
SERIES
32 32 33 33/34 34/36 32/34 32/34
OPERATING WT (Lb) 127 143 153/157 176/185 195/197 219 237
COMPRESSOR
Type
Reciprocating Scroll/Reciprocating Scroll
REFRIGERANT
Control
Charge (Lb) @ 15 ft
R-22
Piston
4.69 4.75 5.63 6.38 7.88 9.25/9.38 10.50/10.25
CONDENSER FAN
Air Discharge
Air Qty (CFM)
Motor HP
Motor RPM (60 Hz)
Propeller Type, Direct Drive
Vertical
1900 1900 2300 3000 3000 3300 3300
1/12 1/12 1/4 1/4 1/4 1/4 1/4
1100 1125 1125 1100 1100 1100 1100
CONDENSER COIL
Face Area (Sq Ft)
Fins per In.
Rows
Circuit
9.10 9.11 12.42 14.8 18.5 22.40 22.40
20 25 20 20 20 20 25
111 1 111
233 3 445
CONNECTION (In. ID)
Vapor
Liquid
Sweat
5/8 5/8 3/4 3/4 7/8 7/8 7/8
3/8
REFRIGERANT TUBES*
(In. OD)
Vapor (0–50 Ft Tube Length)
Vapor (Max Diameter for
Long-Line Applications)
Liquid (0–50 Ft Tube Length)
Liquid (For Long-Line
Applications)
5/8 5/8 3/4 3/4 7/8 7/8 1-1/8
3/4 3/4 7/8 7/8 1-1/8 1-1/8 1-1/8
3/8
3/8
UNIT
SIZE SERIES
OUTDOOR
PISTON
INDOOR
PISTON*
018 32 40 52
024 32 49 63
030 33 55 70
036 33 61 76
036 34 57 70
042 34, 36 63 78
048 32/34 73/70 88/86
060 32, 34 76 96
UNIT
SIZE
REQUIRED
SUBCOOLING (°F)
018 14
024 10
030 8
036 (33) 12
036 (34) 14
042 16
048-32/34 10/15
060 10

4
Accessories
* Isolation relay required.
†Fan Motor with ball bearings required.
‡Use with low-ambient controller.
†† Addition of these accessories requires capacitor and relay compressor start assist on all reciprocating compressor applications.
ORDERING NUMBER DESCRIPTION
KAATD0101TDR Time-Delay Relay —All Sizes
KSALA0201R22 Low-Ambient Pressure Switch
32LT660004 (RCD)† MotorMaster®Control —Sizes 018–060
HC34GE232 (RCD) Ball Bearing Fan Motor —Sizes 018, 024
HC40GE232 (RCD) Ball Bearing Fan Motor —Sizes 030–060
KAAFT0101AAA‡ Evaporator Freeze Thermostat —All Sizes
KHAIR0101AAA‡ Isolation Relay —All Sizes
Standard Cycle Protector —036 (33); 042–060
KSACY0101AAA Cycle Protector —All Sizes
KSAHS1001AAA Start Assist —Capacitor and Relay —Sizes 018 (32); 024 (32); 030 (33)
KSAHS1101AAA Start Assist —Capacitor and Relay —Size 036 (34)
KSAHS1501AAA Start Assist —Capacitor and Relay —Size 036 (33), 042
KSAHS1601AAA Start Assist —Capacitor and Relay —Sizes 048 (32, 34), 060 (32, 34)
KAACS0201PTC All Sizes
Standard Crankcase Heater —Sizes 036 (34); 060 (32, 34)
KAACH1001AAA Crankcase Heater —Sizes 018–024 (32); 030 (33)
KAACH1201AAA Crankcase Heater —Sizes 036 (33); 042 (34, 36); 048 (32, 34)
KSASH1101COP Sound Hood —Sizes 018 (32); 024 (32)
KSASH1201COP Sound Hood —Size 030 (33)
KSASH1901CYL Sound Hood —Size 036 (33); 042 (34)
KSASH2001CYL Sound Hood —Sizes 042 (34); (048-32, 34); 060 (32)
KSASH2001BRL Sound Hood —Size 036 (34)
KSASH0601COP Sound Hood —Sizes 042 (36)
KSASH2101COP Sound Hood —Size 060 (34)
KHAOT0301FST Outdoor Thermostat —All Sizes
KHAOT0201SEC Secondary Outdoor Thermostat —All Sizes
KSATX0601HSO†† TXV (Hard Shutoff) —Size 018–042
KSATX0701HSO†† TXV (Hard Shutoff) —Size 048, 060
KHATX0201RPB TXV (RPB) —Size 018
KHATX0301RPB TXV (RPB) —Size 024
KHATX0401RPB TXV (RPB) —Size 030
KHATX0501RPB TXV (RPB) —Sizes 036, 042
KHATX0601RPB TXV (RPB) —Size 048
KHATX0701RPB TXV (RPB) —Size 060
KHAHI0101HPS High-Pressure Switch —All Sizes
P504-8083S (RCD) Filter Drier —Bi-Flow —Sizes 018–036
P504-8163S (RCD) Filter Drier —Bi-Flow —Sizes 042–060
KHALS0401LLS†† Liquid-Line Solenoid Valve (LSV) —All Sizes
THERMOSTAT PKG DESCRIPTION
TSTATCCNHP01-B
Thermostat —Auto Changeover, Non-Programmable, °F/°C, 2-Stage Heat, 1-Stage Cool
TSTATCCPHP01-B Thermostat —Auto Changeover, 7-Day Programmable, °F/°C, 2-Stage Heat, 1-Stage Cool
TSTATCCPDF01-B Thermostat —Auto Changeover, 7-Day Programmable, °F/°C, Dual Fuel
Must be used with Outdoor Sensor (TSTATXXSEN01-B). High-pressure switch must be added
if not supplied with the system.
TSTATCCPRH01-B* Thermidistat
TM
Control —Non-Programmable/Programmable Thermostat with Humidity Control (For
use in Dual Fuel, AC, HP, and 2S applications. Includes Outdoor Air Temperature Sensor.)
TSTATCCBHP01* Builder’s Thermostat —Manual Changeover, Non-Programmable, °F/°C, 2-Stage Heat, 1-Stage Cool,
Heat Pump
TSTATXXSEN01-B Outdoor Air Temperature Sensor
TSTATXXNBP01 Backplate for Non-Programmable Thermostat
TSTATXXPBP01 Backplate for Programmable Thermostat
TSTATXXBBP01 Backplate for Builder’s Thermostat
TSTATXXCNV10 Thermostat Conversion Kit (4 to 5 wire) —10 Pack
*Do not use in zoning heat pump applications.

5
Accessory usage guideline
* For tubing line sets between 50 and 175 ft, refer to the Residential Split-System Long-Line Application Guideline.
‡Required for Low-Ambient Controller (full modulation feature) and MotorMaster Control only.
Accessory description and usage (Listed alphabetically)
1. Ball Bearing Fan Motor
A fan motor with ball bearings which permits speed reduction while maintaining bearing lubrication.
SUGGESTED USE: Required on all units where low-ambient controller (full modulation feature) or MotorMaster® Control has been added.
2. Compressor Start Assist — Capacitor and Relay
Start capacitor and start relay gives hard” boost to compressor motor at each start-up.
SUGGESTED USE: Installations where interconnecting tube length exceeds 50 ft.
Installations where outdoor design temperature exceeds 105°F (40.6°C).
Installations with hard shutoff expansion valve on indoor coil.
Units installed with Low-Ambient Controller.
Units installed with Liquid-Line Solenoid Valve.
3. Compressor Start Assist — PTC
Solid-state electrical device which gives a soft” boost to the compressor at each start-up.
SUGGESTED USE: Installations with marginal power supply.
Replacement installations with rapid pressure balance (RPB) expansion valve on indoor coil.
4. Crankcase Heater
An electric resistance heater which mounts to the base of the compressor to keep the lubricant warm during off cycles. Improves compressor lubrication on restart and
minimizes chance of refrigerant slugging. May or may not include a thermostat control.
SUGGESTED USE: When interconnecting tube length exceeds 50 ft.
When unit will be operated below 55°F (12.8°C) outdoor air temperature. (Use with Low-Ambient Controller.)
5. Cycle Protector
Solid-state timing device which prevents compressor rapid recycling. Control provides an approximate 5-minute delay after power to the compressor has been interrupted
for any reason, including normal room thermostat cycling.
SUGGESTED USE: Installations in areas where power interruptions are frequent.
Where user is likely to play” with the room thermostat.
All commercial installations.
Installations where interconnecting tube length exceeds 50 ft.
High-rise applications.
6. Evaporator Freeze Thermostat
An SPST temperature actuated switch which stops unit operation when evaporator reaches freeze-up conditions.
SUGGESTED USE: All units where Low-Ambient Controller has been added.
7. Filter Drier—Bi-Flow
A device for removing contaminants from refrigerant circulating in a heat pump system: 2-direction flow.
SUGGESTED USE: All field-connected split-system heat pumps.
8. High-Pressure Switch
Auto reset SPST switch activated by refrigerant pressure on high side of refrigerant circuit. Cycles compressor off if refrigerant pressure rises to 426 ± 10 psig
and resets at 320 ± 20 psig. Provides protection against compressor damage due to loss of outdoor airflow.
SUGGESTED USE: Installations exposed to very dirty” outdoor air.
Installations where condenser inlet air temperature exceeds 125°F.
9. Isolation Relay
An SPDT relay which switches the low-ambient controller out of the outdoor fan motor circuit when the heat pump switches to heating mode.
SUGGESTED USE: All heat pumps where Low-Ambient Controller has been added.
ACCESSORY
REQUIRED FOR
LOW-AMBIENT
APPLICATIONS
(Below 55°F)
REQUIRED FOR
LONG-LINE
APPLICATIONS*
(Over 50 Ft)
Crankcase Heater
Ye s Ye s
Evaporator Freeze Thermostat Ye s N o
Accumulator No No
Compressor Start Assist
Capacitor and Relay
Ye s Ye s
Low Ambient Controller,
MotorMaster® Control,
or
Low-Ambient Pressure Switch
Ye s N o
Wind Baffle See Low-Ambient Instructions No
Coastal Filter No No
Unit Risers Recommended No
Liquid-Line Solenoid Valve
or
Hard Shutoff TXV
No
See Long-Line
Application
Guideline
Ball Bearing Fan Motor Ye s ‡No

6
Accessory description and usage (continued)
10. Liquid-LIne Solenoid Valve (LSV)
An electrically operated shutoff valve to be installed at the outdoor unit and which stops and starts refrigerant liquid flow in response to compressor
operation. Maintains a column of refrigerant liquid ready for action at next compressor operation cycle.
NOTE: Compressor Start Assist — Capacitor and Relay must be used also on reciprocating compressors.
SUGGESTED USE: For improved system performance in air conditioners for certain combinations of indoor and outdoor units. Refer to ARI Unitary Directory.
In certain long-line applications. Refer to the Residential Split-System Long-Line Application Guideline.
11. Low-Ambient Pressure Switch
A long life pressure switch which is mounted to outdoor unit service valve. It is designed to cycle the outdoor fan motor in order to maintain head pressure within normal
operating limits (approximately 100 psig to 225 psig). The control will maintain working head pressure at low-ambient temperatures down to 0°F when properly installed.
SUGGESTED USE: Cooling operation at outdoor temperatures below 55°F (12.8°C).
12. MotorMaster® Control
A fan speed control device activated by a temperature sensor. Designed to control condenser fan motor speed in response to the saturated, condensing temperature during
operation in cooling mode only. For outdoor temperatures down to –20°F, it maintains condensing temperature at 100°F ± 10°F.
SUGGESTED USE: Cooling operation at outdoor temperatures below 55°F.
All commercial installations.
13. Outdoor Air Temperature Sensor
A device that allows the temperature at a remote location (outdoors) to be displayed on the thermostat.
SUGGESTED USE: All Carrier programmable thermostats.
14. Outdoor Thermostat
An SPDT temperature-actuated switch which turns on supplemental electric heaters when outdoor air temperature drops below set point.
SUGGESTED USE: Heat pump installations with multiple-stage supplemental heaters.
15. Secondary Outdoor Thermostat
An SPDT temperature actuated switch which turns on third-stage of supplemental electric heaters when outdoor air temperature drops below the second-stage set point.
SUGGESTED USE: Heat pump installations where 3-stage operation of supplemental heaters is desired.
16. Sound Hood
Wraparound sound reducing cover for the compressor. Reduces the sound level by about 2 dBA.
SUGGESTED USE: Unit installed closer than 15 ft to quiet areas—bedrooms, etc.
Unit installed between 2 houses less than 10 ft apart.
17. Thermostatic Expansion Valve (TXV) Bi-Flow
A modulating flow-control valve which meters refrigerant liquid flow rate into the evaporator in response to the superheat of the refrigerant gas leaving the evaporator.
Kit includes valve, adapter tubes, and external equalizer tube. Both hard shutoff and RPB valves are available. Do not use hard shutoff TXV with Liquid-Line Solenoid
Valve. Hard shutoff TXV requires Compressor Start Assist — Capacitor and Relay on units with single-phase reciprocating compressors.
SUGGESTED USE: For improved system performance in cooling mode for certain combinations of indoor and outdoor units. Refer to ARI Unitary Directory.
Required for use on all zoning systems.
18. Time-Delay Relay
An SPST delay relay which briefly continues operation of the indoor blower motor to provide additional cooling after the compressor cycles off.
SUGGESTED USE: For improved efficiency ratings for certain combinations of indoor and outdoor units. Refer to ARI Unitary Directory.
Required for use on all zoning systems.
SOUND POWER (A-weighted, non-pure tone corrected.)
NOTE: Tested in accordance with ARI standard 270.95. (Not listed with ARI.)
UNIT SIZE
SOUND LEVEL
(dBA)
OCTAVE BAND CENTER FREQUENCY (Hz)
125 250 500 1000 2000 4000 8000
018 78 49.5 58.0 66.5 69.5 67.0 66.5 59.5
024 78 50.5 59.0 64.5 68.0 67.5 67.5 61.5
030 80 57.5 64.5 68.5 72.5 72.5 70.0 64.0
036 81 60.5 67.5 73.0 76.0 73.0 69.5 63.5
042 80 59.0 65.0 70.5 75.5 72.0 69.5 64.0
048 80 54.5 63.5 69.5 75.0 71.0 70.0 67.5
060 80 56.0 64.5 73.0 74.5 71.0 71.0 63.0

7
Electrical data
* Permissible limits of the voltage range at which unit will operate satisfactorily. Operation outside these limits may result in unit failure.
†If wire is applied at ambient greater than 30°C (86°F), consult Table 310-16 of the NEC (ANSI/NFPA 70). The ampacity of nonmetallic-sheathed cable
(NM), trade name ROMEX, shall be that of 60°C (140°F) conductors, per the NEC (ANSI/NFPA 70) Article 336-26.
If other than uncoated (non-plated), 60°or 75°C (140°or 167°F) insulation, copper wire (solid wire for 10 AWG and smaller, stranded wire for larger than
10 AWG) is used, consult applicable tables of the NEC (ANSI/NFPA 70).
‡Length shown is as measured 1 way along the wire path between the unit and the service panel for voltage drop not to exceed 2%.
** Time-delay fuse.
NOTE: Control circuit is 24v on all units and requires external power source. Copper wire must be used from disconnect to unit. All motors/compressors contain
internal overload protection.
FLA —Full Load Amps
LRA —Locked Rotor Amps
MCA —Minimum Circuit Amps
RLA —Rated Load Amps
.
OUTDOOR
UNIT
V/PH
60 Hz
OPERATING VOLTS* COMPRESSOR FAN
FLA MCA
60°C
MIN
WIRE
SIZE†
75°C
MIN
WIRE
SIZE†
60°C
MAX
LENGTH
(Ft)‡
75°C
MAX
LENGTH
(Ft)‡
MAX FUSE**
OR CKT
BKR AMPSMax Min LRA RLA
018-32
208-230/1 253 197
49.0 9.8 0.5 12.8 14 14 70 70 20
024-32 61.0 11.4 0.5 14.8 14 14 50 45 20
030-33 75.0 13.7 1.4 18.5 14 14 40 40 30
036-33 105.0 18.0 1.4 23.9 12 12 50 50 35
036-34 86.0 17.2 1.4 22.9 12 12 55 52 35
042-34 115.0 24.4 1.4 31.9 8 10 97 59 50
042-36 127.0 22.9 1.4 30.0 10 10 67 63 50
048-32 140.0 24.4 1.4 31.9 8 8 90 90 50
048-34 131.0 22.0 1.4 29.0 8 10 107 66 50
060-32 165.0 30.8 1.4 39.9 8 8 75 70 60
060-34 148.0 30.8 1.4 39.9 8 8 75 70 60
HEAT PUMP SYSTEM
This heat pump can be part of a Comfort Heat Pump System which can
provide higher heating supply air temperatures, as well as up to 30 times
more humidity removal in cooling mode. A Comfort Heat Pump System
requires the use of a Variable-Speed Fan Coil with Thermidistat Control.

8
Dimensions—38YCG
A03015
DIMENSIONS (IN.)
UNIT
SIZE SERIES ABCDEFGHJKLMNP
MINIMUM MOUNTING
PAD DIMENSIONS
018 32 22-1/2 25-15/16 3-3/16 5/8 3-11/16 18-1/8 19-3/4 21-5/8 14-3/8 18-7/8 22-1/16 11 5 12 22-1/2 X 22-1/2 024 32 22-1/2 25-15/16 3-3/16 5/8 3-11/16 18-1/8 19-3/4 21-5/8 14-3/8 18-7/8 22-1/16 10 5 13 22-1/2 X 22-1/2 030 33 22-1/2 33-15/16 3-3/16 3/4 3-11/16 18-1/8 19-3/4 21-5/8 14-3/8 18-7/8 22-1/16 12-1/2 12 14 22-1/2 X 22-1/2 036 33, 34 30 27-15/16 3-3/16 3/4 6-1/2 23-1/2 27-1/4 29-1/8 20 26-3/8 29-9/16 16-3/4 15 12 30 X 30 042 34, 36 30 33-15/16 3-1/4 7/8 6-1/2 23-1/2 27-1/4 29-1/8 20 26-3/8 29-9/16 15 15-3/4 13-1/2 30 X 30 048 32, 34 30 39-15/16 3-1/4 7/8 6-1/2 23-1/2 27-1/4 29-1/8 20 26-3/8 29-9/16 15 15-3/4 15-1/2 30 X 30 060 32, 34 30 39-15/16 3-1/4 7/8 6-1/2 23-1/2 27-1/4 29-1/8 20 26-3/8 29-9/16 13-3/4 15-5/8 15 30 X 30

9
38YCG BALANCE POINT WORKSHEET
BUILDING HEAT LOSS, 1000 BTU/HR
UNIT INTEGRATED HEATING CAPACITY, 1000 BTU/HR
OUTDOOR TEMPERATURE, °F
-10 010
20 30 40 50 60 70 80
2.9 5.9 8.8 11.7 14.7 17.6 20.5
70 60 50 40 30 20 10
KW
BASED ON INDOOR ENT. AIR AT
70°F AND AT RATED CFM
23.4
80
38YCG01832 F(A,B)4BNF018
38YCG02432 F(A,B)4BNF024
38YCG03033 F(A,B)4BNF030
38YCG04832/34 F(A,B)4BN(F,B)048
38YCG06032/34 F(A,B)4BN(F,B)060
Printed in U.S.A.
38YCG03633/34 F(A,B)4BNF036
38YCG04234/36 F(A,B)4BN(F,B)042
A03125

10
Combination ratings
UNIT
SIZE-SERIES
INDOOR
MODEL
ARI STANDARD RATINGS*
Cooling Heating
TC
SEER
EER
High-Temp Low-Temp
HSPF
Factory-
Supplied
Enhance-
ment
Standard
Rating Accessory
TXV**
Carrier
Gas Furnace
or
Accessory
TDR‡TC COP TC COP
018-32
*F(A,B)4(A,B)N(F,C)018 17,000 TDR 10.00 ——8.80 17,500 3.00 11,000 2.22 7.0
CC5A/CD5AA018 17,500 NONE —10.00 10.00 8.85 17,000 2.94 11,000 2.18 6.8
CC5A/CD5AA024 17,800 NONE —10.10 10.10 9.05 17,500 3.08 11,200 2.24 7.0
CE3AA024 17,800 NONE —10.10 10.10 9.10 17,500 3.08 11,200 2.26 7.0
CF5AA024 17,800 NONE —10.10 10.10 9.10 17,500 3.10 11,300 2.26 7.2
CK3BA024 17,800 NONE —10.10 10.10 9.00 17,500 3.16 11,300 2.26 7.0
CK5A/CK5BA018 17,500 NONE —10.00 10.00 8.85 17,000 3.04 11,200 2.24 6.8
CK5A/CK5BA024 17,800 NONE —10.10 10.10 9.00 17,500 3.16 11,300 2.26 7.0
CK5A/CK5BW024 17,800 NONE —10.10 10.10 9.00 17,500 3.16 11,300 2.26 7.0
F(A,B)4(A,B)N(F,C)024 18,000 TDR 10.10 ——8.95 18,000 3.12 11,400 2.26 7.2
FC4(B,C)NF024 18,000 TDR&TXV 10.10 ——8.80 18,000 3.14 11,300 2.28 7.2
FF1DNA018 17,000 TDR 10.00 ——9.00 17,500 3.02 11,000 2.22 7.0
FF1DNA024 17,800 TDR 10.20 ——9.05 17,600 3.16 11,300 2.28 7.2
FG3AAA024 17,500 NONE —10.00 10.00 8.65 16,800 3.06 11,200 2.26 6.8
COILS + 58CV(A,X)070-12 VARIABLE-SPEED FURNACE
CC5A/CD5AA024 17,500 TDR 11.00 ——9.70 17,000 3.06 10,200 2.26 7.0
CC5A/CD5AW024 17,500 TDR 11.00 ——9.70 17,000 3.06 10,200 2.26 7.0
CE3AA024 17,500 TDR 11.00 ——9.70 17,000 3.08 10,300 2.28 7.0
CK3BA024 17,500 TDR 11.00 ——9.85 17,000 3.24 10,400 2.34 7.2
CK5A/CK5BA024 17,500 TDR 11.00 ——9.85 17,000 3.24 10,400 2.34 7.2
CK5A/CK5BW024 17,500 TDR 11.00 ——9.85 17,000 3.24 10,400 2.34 7.2
024-32
*F(A,B)4(A,B)N(F,C)024 22,600 TDR 10.00 ——8.90 22,800 3.20 14,000 2.28 7.0
CC5A/CD5AA024 22,400 NONE —10.00 10.00 8.85 22,800 3.10 13,800 2.24 6.9
CC5A/CD5AA030 22,800 NONE —10.00 10.00 8.90 22,800 3.10 13,900 2.24 6.9
CC5A/CD5AW030 22,800 NONE —10.00 10.00 8.90 22,800 3.10 13,900 2.24 6.9
CE3AA024 22,600 NONE —10.00 10.00 8.90 22,800 3.14 13,900 2.26 6.9
CE3AA030 23,000 NONE —10.00 10.00 8.95 22,800 3.22 14,000 2.28 7.0
CF5AA024 22,600 NONE —10.00 10.00 8.90 22,800 3.14 13,900 2.26 6.9
CK3BA024 22,600 NONE —10.00 10.00 8.85 22,800 3.22 14,100 2.30 7.0
CK3BA030 22,800 NONE —10.00 10.00 8.90 22,800 3.18 14,100 2.28 6.9
CK5A/CK5BA024 22,600 NONE —10.00 10.00 8.90 22,800 3.20 14,000 2.28 7.0
CK5A/CK5BA030 22,800 NONE —10.00 10.00 8.90 22,800 3.18 14,100 2.28 6.9
CK5A/CK5BW024 22,600 NONE —10.00 10.00 8.90 22,800 3.20 14,000 2.28 7.0
CK5A/CK5BW030 22,800 NONE —10.00 10.00 8.90 22,800 3.18 14,100 2.28 6.9
F(A,B)4(A,B)N(F,C)030 22,800 TDR 10.00 ——9.00 22,800 3.22 14,000 2.30 7.0
FC4(B,C)NF024 22,600 TDR&TXV 10.00 ——8.90 22,800 3.20 14,000 2.28 7.0
FC4(B,C)NF030 22,800 TDR&TXV 10.00 ——8.80 22,800 3.22 14,000 2.30 7.0
FF1DNA024 22,000 TDR 10.00 ——9.05 22,800 3.18 14,100 2.28 7.0
FF1DNA030 23,000 TDR 10.00 ——9.05 22,800 3.24 14,200 2.30 7.0
FK4(C,D)NF001 23,000 TDR&TXV 11.00 ——9.95 22,000 3.38 13,400 2.44 7.2
FK4(C,D)NF002 23,200 TDR&TXV 11.10 ——10.00 21,000 3.40 13,500 2.46 7.0
COILS + 58CV(A,X)070-12 VARIABLE-SPEED FURNACE
CC5A/CD5AA030 22,800 TDR 11.00 ——9.65 20,600 3.22 12,800 2.32 7.0
CC5A/CD5AW030 22,800 TDR 11.00 ——9.65 20,600 3.22 12,800 2.32 7.0
CE3AA030 22,800 TDR 11.00 ——9.70 21,000 3.30 13,100 2.36 7.0
CK3BA030 22,800 TDR 11.00 ——9.65 21,000 3.34 13,200 2.36 7.0
CK5A/CK5BA030 22,800 TDR 11.00 ——9.65 21,000 3.34 13,200 2.36 7.0
CK5A/CK5BW030 22,800 TDR 11.00 ——9.65 21,000 3.34 13,200 2.36 7.0
030-33
*F(A,B)4(A,B)N(F,C)030 28,200 TDR 10.00 ——9.20 29,000 3.08 17,100 2.20 7.2
CC5A/CD5AA030 27,800 NONE —10.00 10.00 9.10 28,600 3.00 17,000 2.16 7.0
CC5A/CD5AA036 28,600 NONE —10.20 10.20 9.30 29,200 3.14 17,300 2.20 7.2
CC5A/CD5AW030 27,800 NONE —10.00 10.00 9.10 28,600 3.00 17,000 2.16 7.0
CC5A/CD5AW036 28,600 NONE —10.20 10.20 9.30 29,200 3.14 17,300 2.20 7.2
CE3AA030 28,000 NONE —10.00 10.00 9.15 29,000 3.08 17,200 2.18 7.0
CE3AA036 28,200 NONE —10.00 10.00 9.25 29,000 3.08 17,200 2.20 7.2
CF5AA036 28,200 NONE —10.00 10.00 9.30 29,000 3.10 17,300 2.20 7.2
CK3BA030 27,800 NONE —10.00 10.00 9.15 28,600 3.06 17,100 2.18 7.0
CK3BA036 28,600 NONE —10.20 10.20 9.40 29,200 3.18 17,400 2.24 7.2
CK5A/CK5BA030 27,800 NONE —10.00 10.00 9.15 28,600 3.06 17,100 2.18 7.0
CK5A/CK5BA036 28,600 NONE —10.20 10.20 9.40 29,200 3.18 17,400 2.24 7.2
CK5A/CK5BT036 28,600 NONE —10.20 10.20 9.40 29,200 3.18 17,400 2.24 7.2
CK5A/CK5BW030 27,800 NONE —10.00 10.00 9.15 28,600 3.06 17,100 2.18 7.0
CK5A/CK5BW036 28,600 NONE —10.20 10.20 9.40 29,200 3.18 17,400 2.24 7.2
F(A,B)4(A,B)N(F,C)036 28,400 TDR 10.00 ——9.20 29,200 3.08 17,500 2.18 7.2
FC4(B,C)NF030 28,200 TDR&TXV 10.00 ——9.05 29,000 3.08 17,100 2.20 7.2
FC4(B,C)NF036 28,400 TDR&TXV 10.00 ——8.85 29,200 3.08 17,500 2.18 7.2
FF1DNA030 28,200 TDR 10.00 ——9.20 29,000 3.10 17,400 2.18 7.2
FG3AAA036 28,200 NONE —10.00 10.00 9.10 29,000 3.08 17,200 2.20 7.2
FK4(C,D)NF001 28,200 TDR&TXV 10.50 ——9.95 28,000 3.18 16,500 2.30 7.3
FK4(C,D)NF002 28,400 TDR&TXV 11.00 ——10.00 28,200 3.26 16,600 2.32 7.5
FK4(C,D)NF003 28,800 TDR&TXV 11.00 ——10.30 28,000 3.30 16,400 2.36 7.5
COILS + 58CV(A,X)070-12 VARIABLE-SPEED FURNACE
CC5A/CD5AA036 28,600 TDR 11.00 ——10.10 27,400 3.20 16,000 2.30 7.2
CE3AA036 28,000 TDR 10.80 ——9.95 27,400 3.14 16,000 2.28 7.2
CK3BA036 28,600 TDR 11.00 ——10.10 27,400 3.24 16,300 2.32 7.2
CK5A/CK5BA036 28,600 TDR 11.00 ——10.10 27,400 3.24 16,300 2.32 7.2
CK5A/CK5BT036 28,600 TDR 11.00 ——10.10 27,400 3.24 16,300 2.32 7.2
COILS + 58CV(A,X)090-16 VARIABLE-SPEED FURNACE
CC5A/CD5AA036 28,600 TDR 11.00 ——10.25 27,400 3.22 15,900 2.32 7.2
CC5A/CD5AW036 28,600 TDR 11.00 ——10.25 27,400 3.22 15,900 2.32 7.2
See notes on pg. 13.