Cary Audio Design SA-200.2 ES User manual

OWNER’S MANUAL
oooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooo
ooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooo
SA-200.2 ES
Power Amplier
NOTE: Before installing your new component, please read this manual
carefully as it will inform you of the product specications, proper
installation and correct operating procedures for your unit. Also included
in this manual are guidelines on how to service and care for your new
Cary Audio Design product.

TABLE OF CONTENTS
Important Safety Instructions ............................................................................................................... 2
Welcome ................................................................................................................................................. 5
Installation ............................................................................................................................................. 7
Specifications .......................................................................................................................................... 8
Operation
Front Panel ............................................................................................................................................ 9
Rear Panel ........................................................................................................................................... 10
Service and Care
Care and Cleaning ................................................................................................................................ 13
AC Power Fuse Replacement ................................................................................................................. 13
Factory Service .................................................................................................................................... 13
Non-Warranty Repairs .......................................................................................................................... 14
Limited Warranty .................................................................................................................................. 15!

IMPORTANT SAFETY INSTRUCTIONS
!
!
Please read these important safety instructions before operating this equipment.
1. Before powering up the equipment, read all safety and operating instructions and follow them as instructed. Retain the
safety and operating instructions for future reference.
2. Do not place the unit on an unstable cart, stand, tripod, bracket, or table. The unit may fall, causing injury to a person
or damage to the unit. Mount the unit according to the manufacturer’s instructions with the suggested mounting
accessory.
3. Mount the unit to a wall or ceiling only in the manner recommended by the manufacturer.
4. Do not use the unit near water (for example, near a swimming pool, bath tub, wash bowl, kitchen sink, or laundry tub)
or in a damp environment (like a basement or outside in the rain).
5. Clean only with a dry cloth.
6. Do not push objects of any kind into the unit through openings as they could touch dangerous voltage points and short-
out parts, possibly resulting in a fire or electric shock. Avoid spilling liquid of any kind on the unit. If water or any metal
object (such as a paper clip, coin, or staple) accidentally falls inside the unit, disconnect it from the AC power source
immediately and contact Cary Audio Design for further instructions.
7. Position the unit away from heat sources such as radiators, heat registers, stoves, or other units (including amplifiers)
that produce heat.
8. This unit is not intended to be used on soft supported items (like blankets, pillows, etc.).
9. This unit is not suitable for use in locations where children are likely to be present.
10. Slots and openings in the cabinet create ventilation to protect the component from overheating. These openings on the
top and bottom panels must remain unobstructed. Allow at least 6 inches (16cm) of clearance above the unit and an
opening behind the unit for airflow. Do not place the unit on a bed, sofa, rug, built- in bookcase, or rack
without adequate ventilation.
11. Use only those attachments recommended by the unit manufacturer, as others may cause hazards.
12. This unit requires a reliable connection to the socket/outlet with protective earthing by means of the
specified power cord set.
13. As a safety feature, the unit may be equipped with a polarized alternating current line plug in which one blade is wider
than the other. This plug will fit into the power outlet only one way. If you cannot insert the plug fully into the outlet,
try reversing the plug. If the plug still will not fit, contact a licensed electrician to update your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
14. Operate the unit only from the power source indicated on the marking label. If you are unsure of the type of power
supplied to your home, consult your unit dealer or local power company.
15. Arrange power supply cords so that they do not suffer from foot traffic or pinching by items placed on or against them.
Pay close attention to cords where plug enter the AC outlet and where they exit from the unit.
16. For added protection during a lightning storm or when the component is idle for long periods of time, unplug the unit
from the wall outlet and disconnect the antenna or cable system. This will help protect the unit from lightning and
power line surge damage.
17. Do not locate an outside antenna system in the vicinity of overhead power lines or other electric light or power circuits.
When installing an outside antenna system, take extreme care to avoid touching the power lines or circuits; contact with
them could be fatal.
18. Do not overload wall outlets, extension cords, or integral convenience receptacles as this increases the risk of fire or
electric shock.
19. External wiring connected to terminals of this unit shall be installed by a skilled person.
20. When replacement parts are required, be sure the service technician has used replacement parts specified by the
manufacturer or those having the same characteristics as the original parts. Unauthorized substitutions may result in
fire, electric shock or other hazards.
21. Upon completion of any service or repairs to the unit, ask the service technician to perform safety checks to
ensure the unit is in proper operating condition.
2

IMPORTANT SAFETY INSTRUCTIONS
!
!
22. Before connecting a new product to your audio or home theater system, turn off all other equipment (preferably unplugging
them from the AC power source). Many audio components feature automatic turn-on circuits that may activate during an
installation, potentially causing damage to electronic components and/or speakers. This type of damage is not covered by
product warranties, and Cary Audio specifically disclaims responsibility for any
such damage.
23. The removable power cord provided with your unit was specifically designed for use with this product,
but other AC cords
ma y be used. Consult your dealer for advice on AC power cords and high quality wire
in your system.
24. The fuse is located inside the chassis and is not user serviceable. If the unit does not power up, contact an authorized service
representative
25. Cables running inside walls should have the appropriate markings to indicate compliance and listing by the UL, CSA or other
standards required by the UL, CSA, NEC or your local building code. Questions about cables inside of walls should be
referred to a qualified custom installer, a licensed electrician, or low-voltage contractor.
26. Recording of copyrighted material for other than personal use is illegal without permission of the copyright holder.
CAUTION: High current. Connect to earth before connecting to supply of unit. Unplug the
unit before performing any service.
Unit can be hot. Be careful of burned fingers when handling parts.
Wait one half hour after switching off to handle parts.
NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to call the CATV system installer's attention to article 820-
40 of the NEC, ANSI/NFPA 70, which provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.
FCC INFORMATION FOR USER:
• CAUTION: Any changes or modifications not expressly approved by Cary Audio
Design could void the user's authority to operate the equipment.
• NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device pursuant to Part 15 of the FCC Rules.
• These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates and can radiate radio frequency energy, and if not installed and used in accordance
with the instructions it may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Connect the equipment into an outlet on a circuit different from where the receiver is connected.
OUTDOOR ANTENNA INSTALLATION/SAFE ANTENNA AND CABLE CONNECTION:
• If an outside antenna or cable system is connected to the
equipment, be sure the antenna or cable system is grounded in
order to provide protection against built-up static charges and
voltage surges. Article 810 of the National Electrical Code,
ANSI/NFPA 70 (in Canada, Part 1 of the Canadian Electrical Code)
provides information regarding proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of antenna
discharge unit, connection to grounding electrodes and
requirements for the grounding electrode.
• Outside antenna system should be located well away from power
lines, electric light or power circuits and where it will never come
into contact with these power sources if it should happen to fall.
When installing an outside antenna, extreme care should be taken
to avoid touching power lines, circuits or other power sources as
this could be fatal. Because of the hazards involved, antenna
installation should be left to a professional.
3

IMPORTANT SAFETY INSTRUCTIONS
!
!
Disposal Instructions
NORTH AMERICAN WASTE OF ELECTRICAL AND ELECTRONIC EQUIPMENT DIRECTIVE
When discarding the unit, comply with local rules or regulations. Batteries should never be thrown away or
incinerated but disposed of in accordance with the local regulations concerning battery disposal.
EUROPEAN UNION (EU) WASTE OF ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) DIRECTIVE
The European Union’s WEEE directive requires that products sold into EU countries must have the crossed out trashbin label
on the product (or the package in some cases). As defined by the WEEE directive, this cross-out trashbin label means that
customers and end-users in EU countries should not dispose of electronic and electrical equipment or accessories in household
waste. Customers or end-users in EU countries should contact their local equipment supplier representative or service centre
for information about the waste collection system in the country.
4

WELCOME
!
!
PRODUCT FEATURES
Congratulations!
Thank you for purchasing the SA-200.2 ES power amplifier.
The introduction of the SA-200.2 ES solid-state power amplifier represents the next generation
of the SA-200.2 design. It embodies a modular approach that ensures consistency in
performance, and ease of manufacture and serviceability. In implementing the new design, we
have dramatically improved performance and current-handling capacity over the previous model
while still maintaining the highest levels of sonic quality.
The SA-200.2 ES is a 200 watt stereo amplifier into 8 ohms, (350 watts into 4 ohms), with
balanced and single ended inputs. The amplifier exhibits very high current capability, is stable
into low impedance loads, and features 3 dB of dynamic headroom.
When we designed the SA-200.2 ES power amplifier, one of our primary goals was to create a
product that would give years of consistent and reliable use without any maintenance. To achieve
that goal, we took a hard look at the design and choice of components. For example, we use
high-precision metal film resistors in almost all our circuitry, even in places where their use is not
required. We have overbuilt the output stage and increased the heat dissipating capabilities of
the amplifier by as much as 50% over previous designs. The changes encompass almost every
part of the design, down to the choice of thickness of the chassis sheet metal. The monolithic
front end brought major advantages to the amplifier design with improved temperature stability,
low offset, and a substantial reduction of all types of distortion across the full frequency
spectrum.
Cary Audio has been known for almost three decades as a producer of some of the finest and
most musical tube amplifiers in the world. Based on this heritage we have paid special attention
to the sonic qualities of these new solid-state amplifiers, voicing them to have the proven
attributes of the “Cary Sound” and testing them hundreds of hours with many different speakers.
In our quest to dramatically improve them over our previous efforts, we compared them to some
of the best of the competition, often at much higher price points. This took months of research
and development time, but we would not rest until we were satisfied that we had surpassed our
previous models by a wide margin. The improvements in the power supply have brought gains in
bass performance, which is now much more visceral and controlled even into difficult loads.
Reducing the noise floor, increasing the isolation between the channels, and especially
redesigning the sensitive front end of the amplifier has improved imaging, sound staging and
depth retrieval. The midrange is now more lifelike and palpable. One area of which we are
particularly proud is what we have achieved in transparency, and the way images now hang in
three-dimensional space. The amplifiers were designed to be equally at home in a high-
performance music system or a home cinema setting.
5

WELCOME
!
!
The SA-200.2 ES power amplifier features include:
• Single-ended RCA or XLR balanced inputs
• 2x 200 Watts/8 ohms; 2x 350 Watts/4 ohms
• Remote trigger (works with +3.3 to +24 Volts DC)
• Overbuilt power supply employs a massive 1500 kVA power transformer and in
excess of 82,000 uF of capacitance
• Protection against short circuits, device failures, miswiring, and internal faults.
• Thermal as well as DC offset protection
• Matched output transistors
• Stable with mismatched, reactive or unusual loads
• Soft start circuit prevents “Brown outs” when amplifier is turned on
• High quality RCA (gold plated) and XLR input connectors
• High-quality, heavy-duty speaker output connectors
Our goals in designing this new amplifier were quite extensive, and we believe we met or
exceeded all of them. As a company we strive to be on the cutting edge of our industry, which
requires a lot of research and dedication on our part to bring you the best products possible. We
are confident that the SA-200.2 ES is a superb amplifier that will meet the tests of musical
accuracy, dynamic performance, and long-term reliability.
6

INSTALLATION
!
!
This section describes the unpacking and installation procedures for your new component.
Unpacking
All Cary Audio Design shipping containers have been specially designed to protect their contents
and special care has been taken to prevent damage under normal shipping conditions. Mishandling
should be evident upon inspection of the shipping container. If shipping damage is found after
visual inspection, take care not to destroy the evidence. If necessary, document the damage with
photographs and contact the transport carrier immediately.
Carefully remove your new component from its packing carton and examine it closely for signs of
shipping damage. We strongly recommend saving all original packing cartons to protect your
amplifier from damage should you wish to store it or ship it for after-sales service.
Warranty Card
IN THE USA & CANADA: If you are the original purchaser of a new unit from an AUTHORIZED
CARY AUDIO DESIGN DEALER OR FACTORY DIRECT FROM CARY AUDIO, please fill out the
enclosed warranty registration card and return it to Cary Audio Design within 15 days of your
purchase. Cary Audio Design also suggests that you keep your original packing cartons in case you
ever need to ship the unit when moving to a new home. Warranty restrictions apply. Consult the
warranty section at the end of this manual for details. Please be certain to keep a copy of the
original sales receipt from your AUTHORIZED CARY AUDIO DESIGN DEALER OR FROM CARY
AUDIO to validate the warranty if ever needed. The warranty is for the original purchaser only and
does not transfer to any subsequent owner.
OUTSIDE THE USA & CANADA: Your local Authorized Cary Audio Design Distributor will make
his own warranty policy for your country. Please check with them for the terms of warranty for
your new amplifier.
Placement
!
In general, the location of your new SA-200.2 ES is not critical. Certain precautions must be taken
to ensure optimum performance. Avoid extremely hot locations such as near radiators or other
heating units. Keep the top of the SA-200.2 ES clear of books, paper or other equipment to protect
against overheating! DO NOT place your SA-200.2 ES in a closed bookcase - overheating will
damage the amplifier! Allow 8 to 10 inches above the unit for proper ventilation.
Power Requirements
!
The SA-200.2 ES is designed to operate from house current mains. The design voltage is 120/240
volts AC at 50/60Hz.
Cables
!
The speaker cables from the output posts of the SA-200.2 ES to the speaker system can be any
convenient length your set-up requires. Select speaker cables of sufficient size to preserve the
outstanding performance capabilities of your SA-200.2 ES. Heavy gauge #16 wire is suitable for
distances up to 10 feet; #12 for 25 feet. Most audio dealers will have proper speaker cable in stock
for this purpose.
7

SPECIFICATIONS
!
!
Operating the SA-200.2 ES amplifier is a simple procedure since each unit is designed for long-
term stability in virtually any home operating situation. However, if the unit is operated outside
the parameters outlined in this owner’s manual, damage may occur. Please read this manual
carefully before operating your new SA-200.2 ES.
GENERAL SPECIFICATIONS
................................................................................................................................................
Circuit Type Solid State, Class A/B
................................................................................................................................................
Power Output 2 x 200 Watts @ 8 Ohms from 20 Hz to 20 kHz
2 x 350 Watts @ 4 Ohms from 20 Hz to 20 kHz
................................................................................................................................................
Frequency Response 10 Hz to 50 kHz +/- 0.1 dB
................................................................................................................................................
Signal-to-Noise Ratio >100 dB, “A” Weighted
................................................................................................................................................
Input Impedance 22K Ohms – Unbalanced (RCA jacks)
22K Ohms - Balanced (XLR)
................................................................................................................................................
Voltage Gain 28 dB
................................................................................................................................................
AC Power 117/234 Volts AC @50-60 Hz
................................................................................................................................................
Break-in Time 100 Hours of playing time
................................................................................................................................................
Finish Black epoxy coated steel chassis.
Silver anodized aluminum faceplate. (Black Optional)
................................................................................................................................................
Weight 65 lbs.
................................................................................................................................................
Dimensions 7.5” H x 17.7” W x 19.5” D
................................................................................................................................................
Audio Input 2 RCA jacks, 2 XLR jacks
................................................................................................................................................
Audio Output 2 pair Heavy-Duty, gold-plated binding posts
................................................................................................................................................
THD Less than 0.05% at rated output
................................................................................................................................................
Damping Factor Greater than 400 from 10Hz to 20 kHz
................................................................................................................................................
Remote Trigger 3.3-24v DC at 5mA or greater
8

OPERATION
!
!
FRONT PANEL
POWER BUTTON
Press in to turn on and off. Button will blink while powering up. When button stops blinking, unit
is ready to operate. Please make sure volume control is turned all the way down prior to turning
unit on or off.
9

OPERATION
!
!
REAR PANEL
1. BALANCED (XLR) INPUT JACK (Right Channel)
Provides balanced audio input from source.
2. UNBALANCED (RCA) INPUT JACK (Right Channel)
Provides balanced audio input from source.
3. UNBALANCED (RCA) INPUT JACK (Left Channel)
Provides unbalanced audio input from source.
4. BALANCED (XLR) INPUT JACK (Left Channel)
Provides balanced audio input from source.
NOTE: Please use balanced OR unbalanced connectors. Do NOT use both.
10

OPERATION
!
!
Never make or break connections to the SA-200.2 ES unless the SA-200.2 ES and all
associated components are powered off.
Do not connect the outputs of the SA-200.2 ES to the outputs of other amplifiers.
5. LEFT AND RIGHT SPEAKER OUTPUT CONNECTORS
Provide audio output for the speakers. Output connectors can accept bare speaker
wires or most spade and banana connectors. When using bare speaker wires, loosen the
connector, insert the wire into the receptacle, and tighten the connector. The same
procedure should be used for spade connectors.
6. FUSE HOLDER
Use only 8A (250v) slow blow fuse for AC 120v or 4A (250v) slow blow fuse for AC 240v.
7. AC POWER CONNECTOR/ MAIN POWER SWITCH
Connect to AC mains using the included power supply cord. Turn the main power
switch on before use.
8. REMOTE TRIGGER INPUT
Enables the SA-200.2 ES to be controlled by an external device with a 3.3V DC
minimum to 24V DC maximum trigger output. Connect the trigger output of the external
device to the TRIGGER INPUT of the SA-200.2 ES power amplifier. The SA-200.2 ES will
automatically respond when the external device is powered on and off. When the
controlling device is turned on, the amplifier will turn on after a delay. This delay is
intentional and serves to protect the speakers while the unit stabilizes. During start-up,
you may hear a relay clicking. This is normal.
11

OPERATION
!
!
CONNECTING TO A SUBWOOFER
A subwoofer can be connected either to the preamplifier or processor through its low-level outputs
or to the speaker terminals of the amplifier or speakers and then connected to the high-level
connections of the subwoofer inputs. The black speaker post of the SA-200.2 ES is true ground.
12

SERVICE AND CARE
!
!
CARE AND CLEANING
The cabinet housing and front panel of the SA-200.2 ES may be cleaned with a soft cloth and
Windex or a window cleaner. The frequency of cleaning will be governed by how many hours
the SA-200.2 ES is operated and by operating environment cleanliness.
CAUTION:
• Do not let any liquids spill into the vents on top of the unit.
AC POWER FUSE REPLACEMENT
WARNING: When replacing the AC Fuse, make sure the unit is NOT PLUGGED IN.
The value for the AC Fuse when AC voltage is set to 100v-120v is an 8A (250v) slow blow fuse.
The value for the AC Fuse when AC voltage is set to 200v-240v is a 4A (250v) slow blow fuse.
FACTORY SERVICE
Careful consideration has been given to the design of your SA-200.2 ES to keep maintenance
problems to a minimum. Any problems or requests for service should be referred to our
Customer Service Department at 919-355-0010. DO NOT return the SA-200.2 ES to the factory
without a Return Merchandise Authorization (RMA) number from our online Customer Service
Center (www.caryaudio.com).
Cary Audio will assume no responsibility if the shipping company refuses to pay for damage due to
your improper packing or lack of insurance should the unit be lost or damaged in shipment. Please
retain and always use the original shipping carton for shipping the player. Also, Cary Audio
reserves the right to return products sent in for service in a new box set at the customer’s
expense if the original packing material was damaged in the initial shipment, or if it is deemed
unsatisfactory to use in return shipping.
13

SERVICE AND CARE
!
!
NON-WARRANTY REPAIRS
Cary Audio will provide repair service for its products charging on a time and expense basis. At
this time, the standard non-warranty service bench fee is $125 for the first hour and $95 per
hour thereafter. Parts used for repairs as well as return shipping are additional. This may change
and is not a quote for service. Please call us at 919-355-0010 for more information about out-of-
warranty service and repair fees.
WARNINGS
• MAKE NO ATTEMPT TO PUT THE SA-200.2 ES IN SERVICE WITH THE TOP
COVER REMOVED. CONTACT WITH HIGH VOLTAGES FOUND IN THE UNIT
CAN BE FATAL. COMPLETELY REMOVE AC POWER PLUG FROM THE WALL
AND ALLOW 30 MINUTES FOR THE HIGH VOLTAGE CAPACITORS TO
DISCHARGE THROUGH BLEEDER RESISTORS BEFORE ATTEMPTING TO
CLEAN THE INSIDE OF THE AMPLIFIER
CAUTIONS
• NEVER REMOVE / INSERT AC PLUG WHEN THE UNIT IS ON OR THE AC
POWER SWITCH IS IN THE ON POSITION. OBSTRUCTION OF THE TOP
PORTION OF THE SA-200.2 ES WILL RESULT IN OVERHEATING AND
DAMAGE TO THE AMPLIFIER
!
14

LIMITED WARRANTY
!
!
This warranty has been included with a Cary Audio product that is intended to be sold and used only
within the United States and Canada. Accordingly, this Warranty only applies to Products which are
purchased in the United States or Canada, and only applies while such products are used in the
United States or Canada. Products purchased outside the United States or Canada, and failures
occurring outside the United States or Canada, are not covered by this Warranty.
Cary Audio Warrants to the Original United States and Canada Purchaser for use in the
United States or Canada the Following Cary Audio Products for the Periods Indicated:
1. Power Amplifiers, Integrated Amplifiers, Surround Sound Processors, and Preamplifiers have
a four (4) year for PLATINUM, two (2) year for GOLD, and one (1) year for SILVER, parts
and labor warranty from the date of the original purchase from Cary Audio.
2. CD or SACD players, DVD players, Music Servers, or Digital Music Centers have an eighteen
(18) month for PLATINUM, twelve (12) month for GOLD, six (6) months for SILVER parts
and labor warranty from the date of the original purchase from Cary Audio.
3. Vacuum tubes, if any are used in the component, are offered a 90-day exchange policy
against defects with the exception of the 300B vacuum tube that has a one (1) year
exchange policy from the date of the original purchase from Cary Audio.
Limitations on Non-Cary Audio Provided Services
Certain Cary Audio Products are designed to employ non-Cary Audio provided services (such as, by
way of example only, Spotify, Tidal, etc.), some of which require separate customer subscriptions
and some of which do not, as part of the Products’ functionality. Because Cary Audio cannot control
the providers of such services or the services themselves, the owner of the Product therefore
assumes all risks related to the use of services provided by anyone other than Cary Audio itself. Cary
Audio cannot and does not warrant against and shall have no liability of any kind for any of the
following that are attributable to non-Cary Audio providers or services: (1) interruption,
discontinuance, or other unsatisfactory performance of service, (2) reduced Product functionality
that is so attributable, or (3) any other loss or damage of any kind that is so attributable.
What is Covered and What is Not Covered
Except as specified below, this warranty covers parts and labor to correct all defects in materials and
workmanship. The following are not covered by the warranty:
1. Damage, deterioration, malfunction or failure to meet performance specifications resulting
from:
a. Accident, acts of nature, misuse, abuse, neglect or unauthorized product
modifications
b. Improper installation, removal or maintenance, or failure to follow instructions
supplied with the product.
c. Repair or attempted repair by anyone not authorized by Cary Audio to repair the
product.
d. Any shipment of the product (claims must be presented to the carrier).
e. Any cause other than a product defect.
15

LIMITED WARRANTY
!
!
2. Cleaning, initial set-up, check-ups with no defects found, or charges incurred for installation,
removal or reinstallation of the product.
3. Any product, on which the serial number has been defaced, modified or removed.
4. Batteries.
5. Accessories, including but not limited to, batteries, cables, mounting hardware and brackets,
cleaning accessories, antenna and detachable power cords.
6. Warranty is void if purchase was made from anyone other than directly from Cary Audio or
an authorized Cary Audio dealer.
Who May Enforce the Warranty?
This warranty extends to products purchased directly from Cary Audio or an authorized Cary Audio
dealer. Purchasers should inquire of the dealer regarding the nature and extent of the dealer’s
warranty, if any.
To obtain such warranty service, the original purchaser must complete and send in the Warranty
Registration Card within 15 days of purchase.
What Will We Pay For?
We will pay for all labor and material expenses for items covered by the warranty. Payment of
shipping charges is discussed in the next section of this warranty.
How Can You Get Service?
In the event that the owner needs to return the unit to Cary Audio for service or repair of a
possible defect, he must follow the following steps:
1. Create a new account or login to our Customer Service Center (www.caryaudio.com) to
obtain a Return Merchandise Authorization (RMA) number. Once the account is set up or
you have logged in, click on “Open New RMA” to begin entering the information to create an
RMA that is needed to return or exchange a product. You will be given an RMA number,
which must appear on the label of the box you ship back.
2. Submit a copy of the original sales receipt. Blank receipts will not validate the limited
warranty for service by Cary Audio. The original sales receipt must contain the following
information:
a. The authorized Cary Audio dealer’s name
b. The date of purchase
c. The unit’s sales price
d. The buyer’s name and address
e. Describe in detail the problem.
f. Note the unit’s model number and serial number.
3. Deliver by either of these methods:
a. With all freight and insurance charges prepaid and in its original packing container
or equivalent, ship the component to Cary Audio, 6301 Chapel Hill Road, Raleigh,
NC 27607.
16

LIMITED WARRANTY
!
!
b. Hand-deliver the product to Cary Audio (address noted above) or the nearest
authorized service facility.
Limitation of Implied Warranties
All implied warranties, including warranties of merchantability and fitness for particular purpose,
are limited in duration to the length of this warranty.
Exclusion of Damages
Cary Audio’s liability for any defective product is limited to repair or replacement of the product at
Cary Audio’s option. Cary Audio shall not be liable for damage to other products caused by any
defects in Cary Audio products, damages based upon inconvenience or loss of use of the product
or any other damages, whether incidental, consequential, or otherwise.
How State Law Relates to the Warranty
Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitations or
exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
International Purchasers (Export Markets)
Cary Audio warrants its merchandise to purchasers within the United States and Canada exclusively
for use within the United States or Canada. It provides no other warranties, expressed or implied.
If you are living outside of the United States and Canada, please consult your local dealer or
distributor to determine the details of your local warranty.
17

LIMITED WARRANTY
!
!
18

!
!
19