Casio fx-9750G PLUS User manual

C asio fx 9750 G PLUS
User’s guide
For estimation of isolation and ventilation parts
1. Pipe bend partition to 12 or 24
2. T-connector straight on regular pipe partition to 12 or 24
3. T-connector warped on regular pipe
4. T-connector not centric on regular pipe
5. Cone, long parted to several cones
6. Cone with triangles
7. Cone with radius
8. Cone end
9. Zeppelin
10. Insertion
11. Change angular to round
12. Measure of angle in degrees 200-200 method
13. Medium part to 45 degrees bend on ventilation (spiro)
14. EURO > currency

Casio fx-9750 G PLUS
ON and OFF CASIO:
ON Press (AC)
OFF Press (Shift and AC)
Open program: Drive with arrowbutton black cursor to (PRGM)
Choose from MAIN MENU………….
Press – BLUE EXE…………………Press
LANGUAGE Press
Start program: Press – Choose language Press
Now you have started!!
Read text and press Press
Now you have come to program-menu
Choose the number you wish
And press Press
Answers to questions and press Press
If it is written down to the right on the screen
(Disp) read and Press
If you have problems you can call me??
Veli Orre phone [phone] E-mail: [e-mail] Web: www.bisab.no
AC/ON
SHIFT
AC/ON
EXE
EXE
EXE
EXE
EXE
[email protected]
http://botnia.no

Estimation of BEND
Note! Sections in 4 parts are: 3 whole and 2 halfsections
You get the next measure:
Partition to 12 or 24
The figure measured from the lower edge and up with measuring tape
Partition to 12 parts: start from mark 4
Partition to 24 parts: start from mark 7.
The holes are marked the same as figure, as 1, 2 and 3.
The partition starts from left or right edge and follows the middle line,
measures get bigger, at the end the last is overlapping.
Partition direction
You use only measuring tape during the whole estimation!!
Overlappin
g
Center radius
Half section
from the edge
Full section
Keep distance
Middle line
Figure to pattern
The distance of the holes from the edge
Pattern length with overlapping

T-connector
Combined:
Straight T-connector
Warped T-connector
Side T-connector
You get the next measure:
Partition to 12 or 24
Middle line
difference
Diameter
Regular pipe
Angle to
regular pipe
Figure to patter
The figure is
measured from
below
Partition direction
Diameterr T-connecto

Page 5
Long cone: several cones in a row
Large diameter Center difference
Partition
Small diameter
Whole length to cone
Thereafter, the program goes to program: “Cone with triangles”.
Measure to cone come after each other continuously, starting from small cone and ending
with the last large cone.
Please remember partition, (even numbers) and look for or overlap to all cones.

Cone with triangles
You can choose partition yourself
Here is only half part of the cone, so you have to draw a similar part to get the
whole cone.
Small diameter
Length
to cone
Large diameter
Center difference
Small
diameter
parted to 6
Large
diameter
parted to 6

Cone with radius
Partition is 12 or you can choose quantity of partitions yourself.
Small
diameter
Large
diameter
Length to
crossing
Small radius
Large radius

Conical end or finish.
Casio asks about isolation diameter or pipe diameter.
You get large radius or small radius.
Draw a big circle and a small circle, take away ¼ part from the drawing and overlap.
Small
diameter
Large
diameter
Overlapping
¼ part

Diameter
Attention: Even numbers
Please remember !!! Quantity of sections should be even numbers
Figures on the sides Straight
Partition to pattern

Insertion
Measure to
insertione
Shorter
Shorter
Diameter
Length to straight line
Length to straight line
Turning-point
Measre to insertone
Shortened length
Shortert
Shortert