Cassia X2000 User manual

CASSIA X2000 Bluetooth Router
QUICK START GUIDE
Copyright © 2021 Cassia Networks, Inc. Cassia Networks and the
Cassia Networks logo are trademarks of Cassia Networks, Inc.

I. INCLUDED IN PACKAGE
GETTING STARTED - ENGLISH
2. Pole Mounting Straps (2) 3. Extra Top Screw Covers (2)1. X2000 Router (1)
4. Cable Glands (2) 5. USB Hole Silicone Plug (1) 6. Mounting Bracket (1)
7. Slotted Screwdriver (1) 8. Anchors with Screws (2*4) 9. Quick Start Guide (1)
1
4
3
2
6
5
87
9
CASSIA X2000 Bluetooth Router
QUICK START GUIDE
1

II. HEAD & BASE
CON USB
ETH/PoE
BT0 BT1
RESET DC 12V
BT1 BT0 AC 4G WiFi ETH SYS PWR
Ground Cable
Ethernet and PoE
USB 2.0
Not used
Reset
12V DC
LED Lights
Opt. external Bluetooth
antenna connectors
2

Please select the corresponding steps according to your router configurations.
III. MOUNTING & INSTALLATION
1) Install USB Cellular modem inside X2000
Step 1：Remove the top screw cover Step 2：Use cross screwdriver to open
the top cap
Step 3: Connect USB cellular modem
to USB port
Step 4: Install the top cap, tighten the
screws and insert the top screw cover
CON
USB
4G
top screw cover
top screw cover
3

Step 3: Connect USB cable to USB
port
Step 4: Pass the USB cable through the USB
hole, install the top cap, install the silicone
plug in USB hole, and then connect the USB
cellular modem to USB cable
2) Install USB Cellular modem outside X2000
Step 1：Open the top cap Step 2：Use slotted screwdriver to remove
the USB hole plug (M20X1.5. Please don’t
mix with the ETH/PoE plug)
CON
USB
Remove
4G
4

NOTE: The side of the mounting bracket facing the wall and pole is sharp. Please
don’t hurt your hands.
Wall Mount Pole Mount
3) Mount the X2000 mounting bracket in a vertical orientation onto a
wall or pole with the supplied mounting kit
4) Slide X2000 down on the X2000 mounting bracket
Pole Mount
Wall Mount
5

NOTE: In order to remove the Ethernet cable once it's been installed, please use the
supplied screwdriver in the X2000 box or a small pointed tool of your choosing to
depress the plastic release tab on the cable. See image below.
5) Connect Ethernet cable and PoE
abc
Remove the ETH/PoE plug (M22X1.5. Please don’t mix with the USB hole plug),
pass the Ethernet cable through the cable gland, insert the RJ-45 connector into
the Ethernet port of X2000, and tighten the cable gland in the order of a, b, c. The
torque of step c should be less than the torque of step a.
NOTE: When removing the cable gland, please follow the order of c, b, a. Otherwise
X2000 will be damaged.
b
ETH/PoE
a
ETH/PoE
c
ETH/PoE
ETH/PoE
6

7) For outdoor X2000 installations, please connect the ground
cable to ensure X2000’s safety
ETH/PoE
BT0 BT1
RESET DC 12V
BT1 BT0 AC 4G WiFi ETH SYS PWR
Ground Cable
6) Connect 12V DC power cable and cable gland to X2000 in the
same way as step 5
abc
DC power adapter
DC 12V
7

IV. SETUP BLUETOOTH ROUTER
1) Setup using Wi-Fi Hotspot
a. The Cassia Bluetooth router provides a Wi-Fi hotspot for initial
setup. Its SSID is cassia-xxxxxx. The xxxxxx is the last 6-digits of
router MAC ID. The default password of the Wi-Fi hotspot is the
same as SSID.
b. Power on the Cassia router, search Wi-Fi hotspot SSID on your
computer, then connect to the Wi-Fi hotspot.�
c. Please open an Internet browser on your computer, then enter
the router’s default IP address: 192.168.40.1. The default login is
admin/admin.
2) Setup using Ethernet connection
a. Connect the Cassia Bluetooth router to a managed Ethernet
switch and access the DHCP table or scan using a port scanning
tool to locate the IP address assigned to the router’s MAC ID.�
b. Open an Internet browser on a computer that is connected to
the same network and enter the IP address discovered above. The
default login is admin/admin.
As part of your first login, you will be prompted to change the default
password. If you forget your password or can’t find the Wi-Fi hotspot,
please reset the router to default settings by pressing and holding the reset
button for 10 seconds.
After login the router’s configuration webpage, please follow Router Quick
Start Guide in
https://www.cassianetworks.com/knowledge-base/general-documents/
to finish the router configuration.
�
8

Bluetooth Low Energy: 4.0/4.1/4.2/5.0
Wi-Fi: 802.11 a/b/g/n/ac, 2.4GHz and 5GHz ISM band
Ethernet: 10/100 Base-T
USB 2.0: supports USB cellular modem
Opt. external Bluetooth antenna connectors: 50 Ohm N type
female connector
Reset button: Factory reset.Please remove the reset plug (M12X1.5) first
LED lights: BT/AC/4G/Wi-Fi/Ethernet/System/Power
V. PRODUCT INTERFACE
Power over Ethernet: 802.3af/at compliant source
Optional: 12V DC power adapter [1]
NOTE: Please don't use two power sources at the same time
[1] Connector type: Interior diameter 2.5 mm / outside diameter 5.5 mm, center +v / outer –v
Output voltage: 12V
Output power: Equal or larger than 12 W
VI. POWER
Operating temperature: -40℃ to +65℃ (-40°F to +149°F)
Humidity: 0% to 90% non-condensing
Storage and transportation temperature: -50℃ to +70℃ (-58°F to
+158°F)
Wind resistance: up to 85-MPH sustained winds & 135-MPH gusts
IP rating: IP66
For additional assistance, please email:
[email protected]
VII. ENVIRONMENTAL
9

VIII. Federal Communications Commission (FCC)
Interference Statement
IX. RF Exposure Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This equipment must be installed and operated in accordance with provided instructions and the antenna(s)
used for this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
End-users and installers must be provided with antenna installation instructions and transmitter operating
conditions for satisfying RF exposure compliance.
For additional information, please go to: https://www.cassianetworks.com
NOTE: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
X. EU Regulatory Conformance
Cassia Networks Inc., hereby declares that Cassia X2000 Series Bluetooth Router is in compliance with directives
listed below:
EMC Directive 2014/30/EU
Low Voltage Directive 2014/35/EU
RED Directive 2014/53/EU
REACH European Regulation (EC) No 1907/2006
RoHS Directive 2011/65/EU & 2015/863/EU
WEEE Directive 2012/19/EU
A Declaration of Conformity for these directives is available for viewing at
https://www.cassianetworks.com
Cassia Networks, Inc.
10

Routeur Bluetooth CASSIA X2000
GUIDE DE DÉMARRAGE RAPIDE
Copyright © 2020 Cassia Networks, Inc. Cassia Networks et le logo
Cassia Networks sont des marques déposées de Cassia Networks, Inc.

I. INCLUS DANS L'EMBALLAGE
DÉMARRER - FRANÇAIS
2. Brides de fixation poteau (2)1. Routeur X2000 (1)
3. Couvre-vis supérieurs supplémentaires (2) 4. Presse-étoupes (2)
5. Prise en silicone pour trou USB (1) 6. Support de montage (1)
7. Tournevis à fente (1) 8. Ancrages avec vis (2*4)
9. Guide de démarrage rapide (1)
1
4
3
2
6
5
87
9
Routeur Bluetooth CASSIA X2000
GUIDE DE DÉMARRAGE RAPIDE
1

II. TÊTE ET BASE
CON USB
ETH/PoE
BT0 BT1
RESET DC 12V
BT1 BT0 AC 4G WiFi ETH SYS PWR
Câble de masse
Ethernet et PoE
USB 2.0
Non utilisé
Réinitialiser
12V DC
Lumières LED
Connecteurs d'antenne
Bluetooth externes facultatifs
2

III. MONTAGE ET INSTALLATION
1) Installez le modem cellulaire USB à l'intérieur du X2000
Étape 1: Retirez les couvercles de vis
supérieurs
Étape 2: Utilisez un tournevis cruciforme
pour ouvrir le capuchon supérieur
Étape 3: Connectez le modem
cellulaire USB au port USB
Étape 4: Installez le capuchon supérieur,
serrez les vis et insérez les couvercles de
vis supérieurs
CON
USB
4G
Veuillez sélectionner les étapes correspondantes en fonction de la configuration de
votre routeur.
Couvercle de
vis supérieur
Couvercle de
vis supérieur
3

Étape 3: Connectez le câble USB au
port USB
Étape 4: Faites passer le câble USB à travers
le trou USB, installez le capuchon supérieur,
installez la fiche en silicone dans le trou USB,
puis connectez le modem cellulaire USB au
câble USB
2) Installer le modem cellulaire USB en dehors du X2000
Étape 1: Ouvrez le capuchon superieur Étape 2: Utilisez un tournevis plat pour
retirer la fiche du trou USB (M20X1.5.
Veuillez ne pas mélanger avec la fiche
ETH/PoE)
CON
USB
Supprimer
4G
4

Montage mural Montage sur poteau
3) Montez le support de montage X2000 dans une orientation
verticale sur un mur ou un poteau avec la trousse de montage
fournie.
REMARQUE: Le côté du support de montage faisant face au mur et au poteau est
tranchant. S'il vous plait, ne vous blessez pas les mains.
4) Faites glisser X2000 vers le bas sur le support de montage
X2000.
Montage sur poteau
Montage mural
5

5) Connectez le câble Ethernet et PoE
abc
Retirez la prise ETH/PoE (M22X1.5. Veuillez ne pas mélanger avec la prise USB),
passez le câble Ethernet à travers le presse-étoupe, insérez le connecteur RJ-45
dans le port Ethernet du X2000 et serrez le presse-étoupe dans l'ordre de a, b, c.
Le couple de l'étape c doit être inférieur au couple de l'étape a.
REMARQUE: Lors du retrait du presse-étoupe, veuillez suivre l'ordre ou c, b, a.
Sinon, X2000 sera endommagé.
REMARQUE: afin de retirer le câble Ethernet une fois qu'il a été installé, veuillez
utiliser le tournevis fourni dans la boîte X2000 ou un petit outil pointu de votre
choix pour appuyer sur la languette de dégagement en plastique sur le câble. Voir
l'image ci-dessous.
b
ETH/PoE
a
ETH/PoE
c
ETH/PoE
ETH/PoE
6

7) Pour les installations X2000 a l’extérieur, veuillez connecter le
câble de masse pour assurer la sécurité du X2000.
6) Connectez le câble d'alimentation 12V DC et le presse-étoupe
au X2000 de la même manière qu'à l'étape 5
abc
Adaptateur d'alimentation DC
DC 12V
ETH/PoE
BT0 BT1
RESET DC 12V
BT1 BT0 AC 4G WiFi ETH SYS PWR
Câble de masse
7