Cateye CC-TR200DW User manual

Click the button and follow the in-
structions.
CATEYE V2c/V3
CC-TR200DW/300TW
Quick Start
START

Thank you for purchasing our cyclocomputer CATEYE V2c/V3.
This Quick Start Manual explains how to set up the computer, how to install the unit to your
bicycle, and how to wear the heart rate sensor.
Please set up the unit according to the specified procedure, then it will be ready for use as a
cyclocomputer.
•Before use, read the instruction manual that comes with the product thoroughly
to the end to understand the functions of this unit, and to use it safely in a
correct manner.
Pacemaker users must not use the heart rate sensor provided with V3•
(TR300TW).
Next

This PDF contains a movie file.
When you click on the movie screen, a message regarding security appears. Click the
“Trust in the text” or “Play” button to close the message.
Click the screen again to play the movie.
Next

CATEYE V2c / V3
Quick Start Manual Contents
Click the item you wish to view.
Return to a Cover
Setting up the computer
How to install the speed sensor (movie)
How to wear the heart rate sensor (movie) * V3 (TR300TW) only
How to install the bracket (movie)

Operation of buttons
Set up the computer by operating the buttons as follows.
Check the button position before you start setting up.
SSE
M1/+
M2/-
MENU
Front Back
Press the SSE button, the M1/+ but-
ton, and the M2/- button on the front
of the computer.
Press the MENU button on the back of
the computer.
Next

CATEYE V2c / V3
Quick Start Manual Setting up the computer
Setting the date display
Setting the month
Setting the day
Setting the clock display
Measuring screen
(Setup completed)
Restarting operation
Setting the year
Setting the hour
Setting the minute
Setting the wheel
Setting the speed unit
Preparation for setting up Preparation for setting up
Open the battery cover on the back of the computer
using a coin, and then pull out the insulation sheet.
After pulling out, replace the battery cover as before.*
Insulation sheet
Open
Close
Return to Contents
Next
Return

CATEYE V2c / V3
Quick Start Manual Setting up the computer
Setting the date display
Setting the month
Setting the day
Setting the clock display
Measuring screen
(Setup completed)
Setting the year
Setting the hour
Setting the minute
Setting the wheel
Setting the speed unit
Restarting operation
Preparation for setting up Restarting operation
Press the AC button on the back of the computer.
After full lighting of the screen, the computer changes
to the date display setting screen to start setting up.
AC
Full lighting Setting the date display
Return to Contents
Next
Return

CATEYE V2c / V3
Quick Start Manual Setting up the computer
Setting the month
Setting the day
Setting the clock display
Measuring screen
(Setup completed)
Setting the year
Setting the hour
Setting the minute
Setting the wheel
Setting the speed unit
Setting the date display
Restarting operation
Preparation for setting up Setting the date display
When the M1/+ button or the M2/- button is pressed, either
“YY/MM/DD”, “MM/DD/YY” or “DD/MM/YY” is selected
for the date display. Select the display of your choice.
After selecting, press the SSE button to proceed to the
next step “Setting the year”.
The following description is for the case when*
“YY/MM/DD” is selected.
Date display
SSE
YY/MM/DD
MM/DD/YY
DD/MM/YY
↔ ↔
To the next step
M1/+
M2/-
Return to Contents
Next
Return

CATEYE V2c / V3
Quick Start Manual Setting up the computer
Setting the month
Setting the day
Setting the clock display
Measuring screen
(Setup completed)
Setting the hour
Setting the minute
Setting the wheel
Setting the speed unit
Setting the year
Setting the date display
Restarting operation
Preparation for setting up Setting the year
Pressing the M1/+ button increases the value (“Year” of
the date) flashing, and pressing the M2/- button decreas-
es it. Enter any value.
After entering, press the SSE button to proceed to the next
step “Setting the month”.
Year
SSE
Increase the value To the next step
M1/+
M2/-
Return to Contents
Next
Return

CATEYE V2c / V3
Quick Start Manual Setting up the computer
Setting the day
Setting the clock display
Measuring screen
(Setup completed)
Setting the hour
Setting the minute
Setting the wheel
Setting the speed unit
Setting the month
Setting the year
Setting the date display
Restarting operation
Preparation for setting up Setting the month
Pressing the M1/+ button increases the value (“Month”
of the date) flashing, and pressing the M2/- button de-
creases it. Enter any value.
After entering, press the SSE button to proceed to the next
step “Setting the day”.
Month
SSE
Increase the value To the next step
M1/+
M2/-
Return to Contents
Next
Return