cctv camera pros HCPRO-420SC User manual

For information relating to video surveillance, please contact us, via email at [e-mail],
or by phone at 561-433-8488 / 888-849-2288; or visit our Website: www.cctvcamerapros.com
HCPRO-420SC Fire Sprinkler Security Camera
Hidden CCTV Spy Camera with 680TVL
OSD Manual
More information about this product can be found online on the HCPRO-420SC product page.

HCPRO-420SC Fire Sprinkler Camera
OSD Manual
1. LENS
The LENS menus MANUAL,DC,VIDEO.
2.EXPOSURE
LENS
- Selection of LENS modes.
- The MANUAL means fixed lens
mode.
- DC modes use DC-IRIS lens ,VIDEO
modes use VIDEO-IRIS lens and they control
AE.
The EXPOSURE menus SHUTTER controls, BRINGHTNESS, AGC, D-WDR.
EXPOSURE - SHUTTER
- Setting value of electronic shutter.
- Select mode ：AUTO, FLK,1/50, 1/250,
1/500,1/2000,1/4000,1/5000,1/10000,
1/100000sec.
- When selecting in Auto mode :
The shutter mode from 1/50 to 1/100000, is
controlled with automatic.
- After adjusted data, exit OSD

EXPOSURE - BRIGHTNESS
- BRINGHTNESS : For target
brightness control.
- AE controls this in compliance with a
set bright control. Bright control from 0 to 255.
EXPOSURE – AGC
- AGC : Auto Gain Control level set
OFF/ LOW/ MIDDLE/ HIGH.
EXPOSURE - DWDR
- D-WDR: Digital Wide Dynamic Range
OFF/ ON (LEVEL : 0 to 63).

3.WHITE BAL
The white balance mode.
WHITE BAL
- White Balance control mode selects
ATW1/ATW2/AWC-SET/MANUAL
- ATW ：Auto Tracking White Balance
mode.
- AWC : Auto White Balance Control
mode.
- AWC-SET : When pushing ENTER,
The white balance operate automatically in
fixed color temperature area.
WHITE BAL-MANUAL-COLOR TEMP
INDOOR/ OUTDOOR/ MANUAL
MANUAL : BLUE/ RED
- BLUE : if it higher than default(64), the
white point moves toward BLUE. And it is
lower than it moves toward YELLOW..
- RED : if it higher than default(64),the
white point moves toward RED. And it is lower
than it moves toward GREEN.

4 .BACK LIGHT
BLC and HLC
BACK LIGHT – BLC
- BLC : Back Light Compensation.
- BLC area and GAIN setting.
- HEIGHT/ WIDTH/ LEFT & RIGHT/
TOP & BOTTOM.
BACK LIGHT- HLC
- HLC : High Light Compensation
It is a function which reverses the
area about strong light.
- LEVEL : Setting of HLC level.
- MODE : ALL DAY/ NIGHT ONLY
ALL DAY : Always operating HLC.
NIGHT ONLY : Only night
environment operating. But if day condition,
not operating HLC.

5.DAY & NIGHT
DAY & NIGHT
- D & N change mode sets
- Select of AUTO/ COLOR/B&W/EXT
- AUTO mode: D&N is decided by
AGC gain level.
- COLOR mode: only color mode
operates.
- B/W mode: only B&W mode
operates.
- EXT mode: D&N decision by
external CSD signal.
DAY & NIGHT – AUTO
- D→N LEVEL: It controls gain
level for changing Night mode.
- D→N DELAY: Set the delay time
of DAY to NIGHT.
- N→D LEVEL: It controls gain
level
f
ELAY；Set the delay time
f NIGHT to DAY.
DA
or changing DAY mode.
- N→D D
O
Y & NIGHT – B/W
- BURST: When it is night mode,
color burst signal selects ON/ OFF.
- IR SMART: IR SMART changing
ON/ OFF mode.
- IR LEVEL: HIGH/ LOW.

6.DP
DPC : Dead Pixel Compensation
- Cover the lens then press enter
key.
- Sets for CAM TITLE, MOTION,
ACY, PARK.LINE, IMAGE ADJ,
E.
er can write text 55 characters
- ←,→: When it modify, user can
- CLR: User can remove all text.
-
OS: The text move to the
- END: After finishing CAM TITLE
C
7.SPECIAL
PRIV
LANGUAG
SPECIAL – CAM TITLE
- Us
move revision text.
position.
to the upper menu.

SPECIAL- MOTION
The function is alarm on camera when
being moving by the screen. The setting
zone are 4 area.
area.
- AREASTATE:ON/OFF.
- HEIGHT/WIDTH/LEFT&RIGHT/
TOP&BOTTOM/ DEGREE/: Set the area.
- VIEW: Control alarm display
when MOTION indicates.
ask color can control.
d
- LT/ LB/ RT/ RB/ F/ N / T/: Adjust the
s position and width.
- AREASEL：Select each
SPECIAL- PRIVAC
- The mask controls about the zone
where the privacy is necessary.
- The total mask is 8 zones.
- The each m
SPECIAL-PARK.LINE
- Monitor in the video if the car parke
at right position.
line’

SPECIAL- IMAGE ADJ.
- LENS SHAD: Lens Shading
Compensation.
- 2DNR : 2 Dimension Digital Noise
Reduction.
- MIRROR: Image change mirror
ON/ OFF mode.
- FONT COLOR: Set font color.
- CONTRAESS,SHARPNESS,DISP
LAY,NEG.IMAGE.
setting Camera ID, 485
n set camera ID of each
BAUD RATE:2400/ 4800/ 9600/
38400/ 57600. Unit: bps.
- PROTOCOL: Supporting for
PELCO-D,PELCO-P.
- DISPLAY ID: ON/ OFF.
IDPOS:IDPOSITION
f OSD
SPECIAL – COMM ADJ.
- The
comm.
- CAM ID: When user set a couple
of camera, it ca
camera.
-
19200/
-
SPECIAL – LANGUAGE
- User can set language o
menu.
- VERSION: Version information.

8.RESET
RESET- FACTORY
- FACTORY initial data mode set.
EXIT
- After adjusted data, exit OSD
menu.
9.EXIT