Cecilware GB1K User manual

HOT CAPPUCCINO & COFFEE DISPENSER
Cecilware sells value…Worldwide
45-05 20th Avenue, Long Island City, NY 11105 • 718-932-1414
FAX [phone]
NC66A 12W96
SERIES
GB1K
OCS-3
OPERATION MANUAL
Specifications
Installation &
Operating instructions
Adjustments
Care & Maintenance
Components Illustration
Parts Identification
Wiring Diagram

Electrical Specifications
Model No. Volts Phase Hz Kilo
Watts Number of Heaters Amps Receptacle Nema
No.
Circuit Breaker
GB1K, 120V 160 1.8 115 5-15R 15A
GB1K 120/240 150/60 3.0 115 L14-20R** 20A
GB1K 240 150/60 3.0 115 L6-20R* 20A
120V, 1.8 KW, 15A, Nema 5-15R standard on all models; 3.0 KW, 120/240V units available
** 120/240V, 3 pole, 4 wire grounding type Twist-Plug Receptacle.
For 240V units. Use L6-20R, 2 pole, 3 Wire Twist-Plug Receptacle. For Wiring, refer to Wiring Diagrams.
See Electrical Data Label attached to the back of the unit for proper voltages, breaker sizes and electrical outlet requirements for each model
number listed.
Mechanical Specifications
Model # # of Hoppers Hopper Ca-
pacity (lb.) Width (in.) Depth (in.) Height (in.) Tank
(gal.) Burst Capacity Lit Display Area (W x H) sq. in Ship
Weight
(lb.)
GB1K-LD 188.5 20.5 27 1.5 15 (6.75X13.5)91 70
Height: Add an additional4" when installing with 4" legs.
Add an additional14" min. for water bottle and additional height space to invert bottle over the top.
*Burst Capacities -Max. number of drinks dispensable with available hot water -based on 6 oz. cups.
** Add 2" for line cord and valve fitting clearance.
Plumbing: ¼” water line required.

INSTALLATION REQUIREMENTS:
This equipment is to be installed to comply with the applicable federal, state, or local plumbing codes having jurisdiction.
In addition:
1. A quick disconnect water connection or enough extra coiled tubing (at least the depth of the unit) so that the machine can be moved for cleaning
underneath.
2. An approved back flow prevention device, such as a double check valve to be installed between the machine and the water supply.
INSTALLATION & PRIMING:
1. Flush inlet water line thoroughly before connecting. If pipe sealant is necessary, Teflon tape is commended.
2. Connect water line to the 1/4" flare fitting located at rear of the unit. A shutoff valve in the water supply line is advisable.
3. Turn on water. Check water line and fittings for leaks.
4. Put HEATER Switch OFF.
5. Plug the power cord into a grounded 120 volt, 60 Hz 15 Amp outlet, Single use. It will take 2 to 4 minutes to fill the tank.
6. Put RINSE Switch ON.
7. Press Dispense Button until water flows out of the dispense nozzle ( 6 to 7 min.). Tank will fill up.
8. PUT RINSE Switch OFF.
9. Put HEATER Switch ON and allow 10 to 15 minutes for water to reach brew temperature.
10. Fill hopper with DRY* powdered product, while waiting for water in tank to heat up. See filling instructions.
11. Push Dispensing Button and check the operation of the hopper. A grinding noise will be heard if not properly engaged.
12. Push Dispensing Button and check drink taste. If adjustments are needed, see "Water Flow Adjustments".
NORMAL DAILY DISPENSER OPERATION
FILLING
1. Open Front Door and lift Top Cover.
2. Fill hopper to desired level with DRY powdered mix.
*Moist product will clog hopper and the unit will not operate properly.
*Never REFRIGERATE powdered product.
Do not overfill or pack product down when filling.
3. Close Top Cover and Door.
DISPENSING
1. Place cup under mixing chamber spout.
2. a) For Manual Units (without Timer): Press and hold
push button until cup is approximately 2/3 full.
b) For Automatic Units (with Timer):
Press and release push button. Cup will fill to size set on Timer.
3. Remove cup when flow from mixing chamber has stopped completely.
WATER FLOW and DRINK STRENGTH ADJUSTMENTS
The unit is factory adjusted to dispense as follows:
Water Flow Rate : 1.2 oz./sec.
Powder/Product Flow Rate: 4 oz./sec.
Corresponding Gram Throw Rate: 4 gr. product per1.2 oz. of water.
To increase or decrease Drink Strength, proceed as follows:
1. Remove right hand side Panel of unit. (looking from the front).
2. Locate Flow Adjustment Key inside unit mounted above water valve.
3. Engage Flow Adjustment Key into Flow Controller and rotate counterclockwise (CCW) to
decrease and clockwise (CW) to increase drink strength. When making strength
adjustments, do not turn
Adjustment Key more than 1/8" turn at a time without checking drink strength.
4. Return Adjustment Key back into keyholder. If after maximum adjustment.
3

ITEM NO: DESCRIPTION PART NUMBERS QTY
1TANK TOP ASS'Y 97127 1
2TANK BAFFLE ASS'Y 97128 1
3TANK BAFFLE SEAL 20039 1
4TANK CLAMP ASS'Y 97131 1
5HEATER ELEMENT1750W120V G0140 1
6WASHER, FOR HEATER ELEMENT 07059 2
7NUT, FOR HEATER ELEMENT 03051 2
8TANK WELDMENT ASS'Y 97293 1
9ELBOW, MALE 1/8 NPT, WATER INLET FITTING K330A 1
10 THERMOSTAT 59016 1
11 HI-LIMIT (TEMPERATURE SAFETY GUARD) 59024 1
12 DIRECT MOUNTING SEAL / SILICONE FITTING(.461 ID) M461A 1
13 DRAIN TUBE K525A 1
14 PLUG, SILICONE , FOR DRAIN HOSE M391A 1
15 DRAIN HOSE M483A 1
16 SILICONE HOSE -TANK WATER INLET TO WATER FLOW CONTROL -VALVE M483A 1
17 SILICONE HOSE -TANK TOP TO DISPENSE GROMMET M550A 1
18 HOSE BARB FITTING K435C 1
19 ADJUSTER VALVE ASS'Y #H5107 NPT (ADJUSTMENT KEY INCLUDED) K415A 1
20 HOSE NUT ASS'Y/ WATER INLET K178A 1
21 SOLENOID/ WATER INLET VALVE L477A 1
22 BLOWER DUCT HOSE 16"x(1 " DIA) CD 107 1
23 ELBOW INSERT CD 108 1
24 ELBOW CUP CD 1081
25 FAN / BLOWER DRYER ASS'Y CD56A 1
26 MOUNTING CLIP (VENT. MOTOR) RA67A 1
27 POWER/ ELECTRICAL CORD C035A 1
28 TERMINAL BLOCK 120V OR 240V B117A OR B116A 1
29 BALLAST CE221 1
30 RELAY, (NORMALLY OPEN) OR TIMER (OPTIONAL )1 20V B129A OR 58017 1
31 GB1K FRAME WELDMENT ASS'Y RC85Q 1
32 POWER SWITCH (120V) OR (120/240 V) L069A OR L299A 1
33 RINSE SWITCH L446A 1
34 LEGS (SET OF 4) M172A 1
35 DRIPTRAY PAN metal RM21Q 1
36 DRIP TRAY GRILL RL78A 1
37 HEATER INDICATOR LIGHT (amber) C002A 1
38 HEATER SWITCH, 30A SPST (120V) OR (120/240V) L299A 1
39 WHIPPER MOTOR short shaft CD75A 1
40 SLINGER DISC CD 126 1
41 CHAMBER MOUNTING GROMMET CD66A 1
42 CHAMBER MOUNT CD65A 1
43 "0"RING #125 (used w/ grommet) M379A 1
44 WHIP BLADE CD64A 1
45 EXTENSION TUBE M467A 1
46 WHIP CHAMBER CD63A 1
47 MIXING CHAMBER CD62A 1
48 DISPENSE CUP CD61A 1
49 "O"RING ((#110)(used w / socket CD67A) M378A 1
50 MIXING BOWL SOCKET CD67A 1
51 DOOR PLASTIC COVER/PANEL. BLACK M450A 1
52 DISPENSE BUTTON / SWITCH L455A 1
53 BRACKET, DOOR SWITCH PANEL RF77A 1
54 STARTER BASE (for lamp inside door) B128A 1
55 STARTER, TYPE FS -5, 5-6-8WATT L396A 1
56 DOOR HARNESS ASSY CF19A 1
57 BULB, TYPE F8T5/CW CE76A 1
58 LAMP HOLDER CE220 1
59 300R WELDMENT ASSEMBLY, less components RF73Q
60 LABEL PANEL, CLEAR M464A 2
61 PRODUCT GUIDE CD70A 1
62 NYLON AUGER CD130 1
63 AUGER BUSHING, FRONT CD102 1
64 HOPPER ASS'Y W/COVER (SQUARE 8 LB) CD99A 1
65 AGITATOR CD141 1
66 AUGER BUSHING, BACK CD138 1
67 NUT (FLANGE) CD136 1
68 SCREW, FOR AUGER MOTOR P443A 2
69 AUGER MOTOR (90 RPM) CD150 1
70 SIDE PANELS R046A 2
* Recommended spare parts 5

MAINTENANCE INSTRUCTIONS (See Illustration A):
LIT DISPLAY LAMP AND STARTER REPLACEMENT
1. To replace the lamp, first remove the upper inside door panel. Turn the lamp and pull it out of the lamp holder,
then place the new lamp into the lamp holder and turn it until it snaps into position.
2. To replace the starter,remove the upper inside door panel, turn the starter slightly counter-clockwise and take it
out of the starter base. To install the new starter, snap the starter into the starter base and turn it slightly clockwise
into position.
RECOMMENDED DAILY CLEANING
1.Turn the power switch to OFF.
2.Remove the drip tray with grill and empty the contents. Wash with mild dishwasher detergent and dry.
Cleaning the Hopper
1.Open the cabinet door and raise the top cabinet lid.
2.Take the hopper out of the cabinet.
3.Pull off the elbow chute and remove the hopper cover.
4.Rinse each item thoroughly.
5.Dry all items and reassemble.
Filling the Hopper
1. Open the cabinet door, raise the top cabinet lid.
2. Fill the hopper with the correct product. Note: The Hopper can also be removed for filling.
3. Reposition hopper in the hopper compartment, making sure the hopper is properly seated.
Flushing the Whipper Chamber
1. Turn the POWER switch and RINSE switch to ON.
2. Place a container under dispense nozzle and push the Dispense Button.
Note: On manual dispense machines, push and hold the dispense buttons for 10 seconds.
3. Turn the Rinse switch back to OFF.
Removing and Cleaning the Cappuccino Whipper Chamber
1. Remove the dispense cap by pulling it forward and at the same time twisting it clockwise.
2. Pull the mixing bowl out of the mixing bowl socket.
3. Twist the whipping chamber clockwise and pull it off the mounting plate.
4. Pull the Whipper blade off the motor shaft. Notice the flat keyway on the shaft and the
matching keyway inside the Whipper blade shaft. It is important that these two keyways are lined up when re-assembling the
components.
5. Twist the mounting plate clockwise and pull it off the motor shaft.
6. Slip off the o-ring from the Whipper chamber mounting plate and clean o-ring and o-ring seat.
Removing and Cleaning Mixing Chambers
1. Remove the dispense cap.
2. Pull the mixing bowl out of the mixing bowl socket.
3. Take out the extension tubes.
4. Rinse thoroughly.
6

QUICK START-UP PROCEDURE
1. Flush inlet water line thoroughly before connecting. If pipe sealant is necessary, Teflon tape is commended.
2. Connect water line to the 1/4" flare fitting located at rear of the unit. A shutoff valve in the water supply line is advisable.
3. Turn on water. Check water line and fittings for leaks.
4. Put HEATER Switch OFF.
5. Plug the power cord into a grounded 120 volt, 60 Hz 15 Amp outlet. Single use. It will take 2 to 4 minutes to fill the tank.
6. Put RINSE Switch ON.
7. Press Dispense Button until water flows out of the dispense nozzle ( 6 to 7 min.). Tank will fill up.
8. PUT RINSE Switch OFF.
9. Put HEATER Switch ON and allow 10 to 15 minutes for water to reach brew temperature.
10. Fill hopperwith DRY* powdered product, while waiting for water in tank to heat up. See filling instructions.
11. Push Dispensing Button and check the operation of the hopper. A grinding noise will be heard if not properly engaged.

8