Cedar Ridge CRHFD400RT-M-M User manual

ITEM #0328248
WOOD FIREPLACE MANTEL
Questions, problems, missing parts? Before returning to your retailer, call our
customer service department at 1-866-573-0674, 8:00 a.m - 4:30 p.m., EST,
Monday - Friday or e-mail [email protected].
LS-FBD400-M3-1101
MODEL #CRHFD400RT-M-M
Español p. 17
Cedar Ridge
h e a r t h
®

2
PRODUCT SPECIFICATIONS
16.18 in
21.53 in
44.52 in
42.83 in

3
PART DESCRIPTION Quantity
A Top 1
B Panel 1
C Left Upper Panel 1
D Right Upper Panel 1
E Left Lower Panel 1
F Right Lower Panel 1
G Base 1
H Top Triangle Panel 1
I Backboard 2
J Set Square Support 1
PACKAGE CONTENTS


4
HARDWARE CONTENTS
AA
ST5 Screw
2⅜ in.
16
2Wall Anchor
20
ST4 Screw
1 3/16 in. ST4 Screw
1 9/16 in.
M6 Screw
1 ⅜in.
ST4 Screw
⅝in.
16
Mounting
Bracket
Cam Lock
Cam Dowel
WARNINGS AND CAUTIONS
WARNING
• When tightening screws, do not overtighten. This may cause threads to strip. We recommend
using a hand-powered screwdriver rather than a power screwdriver.
• Do not force screws into holes.
CAUTION
• Forcornerinstallations(optional);ifbaseboardsareinstalledwherethereplaceisintended
tobedisplayed,thenthereplacewillnottushagainstthewall.Foraproperusht,you
may need to remove part of the baseboard moulding if necessary.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt to
assemble the product. Contact customer service for replacement parts.
Estimated Assembly Time: 60 minutes
Tools Required for Assembly: Philips Screwdriver, Flathead Screwdriver, Drill, and Tape
Measure
BB
CC
DD
Picture
Part Description Quantity (Shown to size)
3
18
GG
EE
(not actual size)
Picture
Part Description Quantity (Shown to size)
1
8
4
White Key
HH

(not actual size) (not actual size)
(not actual size)
FF
II
JJ
(not actual size)
2

5
Fig.1
1. Fasten the Left Upper Panel (C) and the
Left Lower Panel (E) with M6 Screw 1-3/8 in.
(JJ) as shown in Fig 1. Do the same thing for
the Right Upper Panel (D) and the Right Lower
Panel (F).

Hardware Used
M6 Screw
1 ⅜in. x4

JJ
2. After assembling the mantel (C, D, E, F),
insert Cam Locks (BB) into Panel (B), screw in
Cam Dowels (AA) into the Left Upper Panel(C)
and the Right Upper Panel (D). Attach Panel
(B) into assembled frame (C, D, E, F) by
tightening the Cam Locks (BB) as shown in
Fig 2.
Fig. 2

Hardware Used
Cam Dowels x4
x4
AA
BB Cam Locks
ASSEMBLY INSTRUCTIONS

6
Hardware Used
Cam Dowels x6
x6
AA
BB Cam Locks
3. Insert Cam Locks (BB) into the Left Lower
Panel (E) and the Right Lower Panel (F),
screw in Cam Dowels (AA) into Base (G).
Attach Base (G) into assembled frame (B, C,
D, E, F) by tightening the Cam Locks (BB)
as shown in Fig 3.
Fig. 3

Skip to step 11 for Corner Mantel Installation.
4. Fasten the batten with ST4 Screw 1-9/16 in.
(II) to the Base (E) as shown in Fig. 4
Fig. 4

Hardware Used
ST4 Screw - 1 9/16 in. x4
II

7
Hardware Used
Cam Dowels x6
x6
AA
BB Cam Locks
5. Insert Cam Locks (BB) into Panel (B), the
Left Upper Panel (C) and the Right Upper
Panel (D), screw in Cam Dowels (AA) into Top
(A). Attach Top (A) into assembled frame (B,
C, D, E, F) by tightening the Cam Locks (BB)
as shown in Fig 5.
Fig. 5

6. Fasten the batten with ST4Screw 1-9/16 in.
(II) to the Top (A) as shown in Fig 6.
Fig. 6

Hardware Used
ST4 Screw - 1 9/16 in. x4
II

8
Fig. 7
Fig. 8
7. After assembling the mantel, lift upright
and push the insert from the front of the
mantel as shown in Fig 7.

8.Positionthereplacetothedesiredplace
as shown in Fig 8.


9
x 3
Fig.9
Fig. 10
ASSEMBLY INSTRUCTIONS CONTINUED (CORNER MANTEL)
9. Turn the Top (A) Panel over. Using the Con-
nector Brackets (GG) that supplied, connect
the Top (A) to the Top Triangle Panel (H) with
ST4 Screw 5/8 in. (FF) as shown in Fig 9.
Hardware Used
ST4 Screw - ⅝in. x 18
Mounting
Bracket
10. Insert Cam Locks (BB) into Panel (B), the
Left Upper Panel (C) and the Right Upper
Panel (D), screw in Cam Dowels (AA) into Top
(A). Attach Top (A) into assembled frame (B,
C, D, E, F) by tightening the Cam Locks (BB)
as shown in Fig 10.
Hardware Used
Cam Dowel x6
x6
AA
BB Cam Lock
FF
GG



10
11. Fasten the batten with ST4Screw 1-9/16 in.
(II) to the Top (A) as shown in Fig 11.
Fig. 11
Fig. 12

Hardware Used
ST4 Screw - 1 9/16 in. x4
12. Attach the left and right Backboard (I) trim
piecestothebackofthereplacewithST4
Screw 1-3/16 in. (DD) as shown in Fig 12.

Hardware Used
ST4 Screw - 1 3/16 in. x8
DD
II

11
41 1/2
1 9/16
Fig. 14
Fig. 13
Hardware Used
Wall Anchor x2
13. After assembling the mantel, lift upright and
push the insert from the front of the mantel as
shown in Fig 13.
14. Drill two holes (5/16 in.) in the corner
wherethereplaceistobedisplayed.Drill
thersthole395/16 in. from the ground up;
and the second hole 41 ½in. from the ground
up as shown in Fig. 14. Put the Wall Anchors
(CC) in the holes by pinching the anchor tabs
together.
Mitered Corner
Joints
CC


12
HH J
EE
31 1/2
Fig. 16
15. Attach the triangular wood block to the holes
drilled in step 8 with ST4 Screw - 2 ⅜ in. (EE) as
shown in Fig. 15. This block is used to support the
Set Square Support (J). For thin walls, insert white
key (HH) into wall anchor and push to “pop” open
anchor wings.
Fig. 15
Hardware Used
EE ST4 Screw - 2 ⅜in. x 2
16.Pushreplaceintocornersothatthe
Top Triangle Panel (H) is resting on top of the
Set Square Support (J) as shown in Fig. 16.
Baseboard
Mitered Corner
Joints
x 1White Key
HH


13
REPLACEMENT PARTS
NOTE: Use only original replacement parts. This will protect your warranty coverage for parts
replaced under warranty.
PARTS UNDER WARRANTY
Call Customer Service toll free at (1-866-573-0674) for referral information.
When calling Customer Service, have ready:
• Yourname
• Youraddress
• Modelandserialnumberofyourheater
• Howheaterwasmalfunctioning
• Typeofgasused(Propane/LPorNaturalgas/NG)
• Purchasedate
• Usually,wewillaskyoutoreturnthedefectiveparttothefactory
PARTS NOT UNDER WARRANTY
Call Customer Service toll free at (1-866-573-0674) for referral information.
When calling Customer Service have ready:
• Modelnumberofyourheater
• Thereplacementpartnumber

14
REPLACEMENT PARTS LIST
For replacement parts, call our customer service department at 1-866-573-0674,
8:00 a.m - 4:30 p.m., EST, Monday - Friday or e-mail [email protected].
Part.Description Part #
AA Cam Dowel PCAM-023
BB Cam Lock PCAM-023
CC Wall Anchor ML066 - 01
DD ST4 Screw 1 3/16 in. GB/T 951 - 4 x 30
EE ST5 Screw 2 3/8 in. GB/T950 - 5 x 60
FF ST4 Screw 5/8 in. GB/T 951 - 4 x 16
GG Corner Bracket SJ 002
HH White Key ML067 - 01
II ST4 Screw 1 9/16 in GB/T 951 4 x 40
JJ M6 Screw 1 3/8 in GB/T 818 6 x 35
PART AVAILABLE----NOT SHOWN
Hardware Package HP007
15
AA BB CC
DD EE FF
GG
HH II
JJ

15
2-YEARLIMITEDWARRANTY
The manufacturer warrants this product to be free from defects in workmanship and material
present at time of shipment from the factory for two (2) years from the date of purchase. This
warranty applies only to the original purchaser. The manufacturer agrees to correct such
defect at no charge or, at our option, replace the product with a comparable or superior model.
Toobtainwarrantyservice,callourcustomerservicedepartmentat1-866-573-0674.You
may be required to present a copy of your sales receipt as proof of purchase. All costs of
removal and reinstallation are the expressed responsibility of the purchaser. Any damage to
theproductbyaccident,misuse,improperinstallation,orbyafxingaccessoriesnotproduced
by the manufacturer, are the purchaser’s responsibility. The manufacturer assumes no
responsibility whatsoever for installation during the warranty period.
There is no further expressed warranty. The manufacturer disclaims any and all implied
warranties. The manufacturer shall not be liable for incidental, consequential, or special
damages arising at or in connection with product use or performance except as may otherwise
beaccordedbylaw.Thiswarrantygivesyouspeciclegalrights,andyoualsohaveother
rights which vary from state to state. This warranty supersedes all prior warranties.
Printed in China