Celebrations Home 9016668 User manual

9016668
12 ft ILLUMINATED GRAND FIR TREE
A
B
C
D
E
TREE - TOP
TREE - CENTER, STICKER 5
TREE - CENTER, STICKER 4
TREE - CENTER, STICKER 3
TREE - CENTER, STICKER 2
1
1
1
1
1
PART DESCRIPTION QUANITY
F
G
H
I
TREE - BOTTOM, STICKER 1
TREE STAND
POWER ADAPTER
SPARE PARTS PACKET
1
1
1
1
PART DESCRIPTION QUANITY
Please check to make sure you have the following parts
Before You Begin
When using electrical products, basic precautions should always be
followed, including the following:
• Do not use seasonal products outdoors unless marked suitable for
indoor and outdoor use. When products are used in outdoor
applications, connect the product to a Ground Fault Circuit Interrupting
(GFCI) outlet. If one is not provided, contact a qualified electrician for
proper installation.
• This seasonal product is not intended for permanent installation or use.
• Do not mount or place the product near gas or electric heaters,
fireplaces, candles, or other similar sources of heat.
• Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
• Do not let lamps rest on the supply cord or on any wire.
• Unplug the product when leaving the house, when retiring for the night,
or if left unattended.
• This is an electric product and not a toy! To avoid risk of fire, burns,
personal injury and electric shock it should not be played with or placed
where small children can reach it.
• Do not use this product for other than its intended use.
* Do not hang ornaments or other objects from cord, wire, or light string.
• Do not close doors or windows on the product or extensions cords as
this may damage the wire insulation.
• Do not cover the product with cloth, paper, or any material that is not a
part of the product when in use.
• This product is equipped with push-in type lamps. Do not twist lamps.
Read and follow all instructions that are on the product or provided with
the product. SAVE THESE INSTRUCTIONS.
CAUTION: USE ONLY POWER ADAPTER THAT WAS PROVIDED
WITH THIS PRODUCT. USING A DIFFERENT POWER ADAPTER
WILL DAMAGE THE LIGHTS AND CAUSE FIRE, ELECTRICAL
SHOCK HAZARD.
FCC NOTICES:
WARNING: Changes or modifications to this unit not expressly approved
by the party responsible forcompliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference
that may cause undesired operation.
IMPORTANT SAFETY INSTRUCTIONS - READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

ASSEMBLING THE TREE
Step 1. Remove the protective caps from the tree bottom and insert the pole into
the tree stand.
Step 2. Continue by inserting the upper tree section(s) to the lower section(s)
until inserting the tree top.
Step 3. Shape the branches to your preference by working from the bottom to
the top. When adjusting branches, ensure that all wires are free of
branch hinges.
Step 4. Insert the green label adapter plug into the wall outlet. All your lights
should now be lit.
Step 5. Shape the tree from the bottom to the top. Start with the branches
farthest from the pole – fan out in a star shape, and continue until
the entire tree is shaped.
Step 6. This is a Simple Shape®tree and no shaping is required. Just slightly
upsweep and shift branches to fill in any gaps for a fuller, uniform look.
Your Christmas tree is now ready to be decorated.
Assembly / Operation Instructions / Troubleshooting
ASSEMBLING THE TREE STAND
Step 1. Choose a location near a wall outlet.
Step 2. Unfold the legs of the tree stand (G) and lay the stand on the floor.
Step 3. Slide the locking disk of the tree stand (G) down until it snaps into place.
Top view Side view
*ELECTRICAL RATING FOR THE TREE
(FOR INDOOR USE ONLY)
Input: 120V, 60Hz, 0.45A
Output: 29V 0.9A
Section 3
Section 1
Section 2
Section 4
Section 5
Tree Top
100S
50S
100S
100S
50S
100S
100S
50S
100S
100S
100S
100S
100S
50S
100S
100S
100S
Adapter
to be plugged
into wall
outlet
Do Not Tamper
Internal Parts
Open the
protective
cap
REPAIRING LOOSE HINGES
Step 1. Place the branch into the slot of the bracket.
Step 2. Insert a new hinge pin through the holes of
the bracket and secure with a washer.
LAMP REPLACEMENT
Step 1. Grasp the power adapter or power
cord plug, and then unplug from the
power outlet. Do not pull the power cord.
Step 2. Lift up lamp lock tab, then pull the lamp
and plastic lamp base straight out of
the lamp-holder.
Step 3. Replace with a new lamp.
TROUBLESHOOTING TIPS
FOR PRE-LIT TREES, IF THE TREE DOES NOT ILLUMINATE
1. Please check to make sure that all connectors are properly connected and
the power adapter cord is plugged into the wall outlet.
2. Turning the poles gently to make sure pole to pole are connected into place.
3. Check for loose connection between light string plugs and extension cords.
4. Please check for loose, broken or missing light bulbs and replace as needed.
Reference figure only
Eye Bolt
Click
Eye Bolt
Do Not Tamper
Internal Parts
Open the
protective
cap
Do Not Tamper
Internal Parts
Open the
protective
cap
Insert Green
Label Extension
Cord into Adapter

MAINTENANCE
SPARE PARTS: This tree package includes hinge pins, washers, bulbs for any replacement or repair that you need to perform on your tree. If extra parts
are needed, contact the Customer Service Team at 1-888-919-0070 between the hours of 8 am and 5 pm MST, Monday through Friday.
STORAGE INSTRUCTIONS
1. Unplug the adapter from the wall outlet first and then remove all ornaments and decorations.
2. Disassemble the tree from the top to the bottom. Start with the tree top and gently lift straight up to remove
from section below and fold all branches toward the pole.
3. Continue by gently lifting straight up each section(s) from the section below and fold all branches toward the
pole until the bottom section is removed from the tree stand. Cover the cap on the poles to avoid damaging
the internal parts.
4. Carefully place all tree sections into shipping box and tape it shut.
5. When not in use, please store your tree in a cool, dry place away from sunlight. Exposing your tree to
excessive heat or humidity may damage your tree.
6. Keep out of reach of pets and children.
Storage / Maintenance Instructions