Cellinx CamPilot URH900A User manual

CamPilot URH900A
CamPilot URH900A
Before installing and using the product, please read this
manual carefully.
Be sure to keep it handy for later reference.
The adaptor and LAN cable are sold separately.
1
Full HD 1ch. Network Video Server
User Manual

Precaution
WARNING
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Do not disassemble or modify the product
If the product is used in an arbitrary manner, it may cause damage to the
product and its surrounding connections.
CAUTIONS
■ Do not open or modify
Do not open the case, as it may be dangerous and cause damages.
■ Do not put objects inside the unit
Make sure that no metal objects or flammable substances get inside the camera. It
could cause fire, short-circuits or damages.
■ Be careful when handling the unit.
To prevent damage, do not drop the camera or subject it to strong shock or
vibration.
■ Install away from electric or magnetic fields.
■ Protect from humidity, dust and high temperature.
An additional case that is temperature-controllable, damp-proof and waterproof is
required for outdoor use.
■ Cleaning
Dirt can be removed from the case only by wiping it with a soft cloth moistened
with a soft detergent solution.
■ Mounting Surface
The mounting surface material must be strong enough to support the product.
■ CamPilot URH900A can be used for surveillance purpose.
Be thoroughly informed of related regulations prior to installation to ensure
compliance with such regulations.
2

Features
CamPilot URH900A is a Network Video Server that transmits real-time high-resolution
digital video and audio data with H.265 / H.264 high compression rate over Internet or
Intranet.
Appearance
1. USB : Reserved
2. RS232
3. ALARM IN / OUT, RS422
4. LED (STREAM, VIDEO, SD CARD)
- STREAM (Yellow) : ON on the accessing status
- VIDEO (Green) : ON when the HD-SDI is inputted.
- SD (Red) : ON when the local storage is detected.
5. SD / SDHC CARD (slot)
1. Reset (factory Default switch)
2. Audio – MIC IN (Ø3.5 stereo jack)
3. Audio – LINE IN (Ø3.5 stereo jack)
4. Audio – LINE OUT (Ø3.5 stereo jack)
5. Video output (HD-SDI, BNC connector)
6. Video input (HD-SDI, BNC connector)
7. Ethernet (10/100/1000 Base-T LAN)
8. Power (Ø5.5x2.1,12V 1A)
1
| Front
| Top | Side
| Rear
8 Pin connector
Overview
3
2 3 4 5
1 3 4 5 6 7 82

Specification
Items Specifications
Video
Video Input HD-SDI
Compression Type H.265, H.264, MJPEG
Resolutions 1080p, 720p, D1 ~ QCIF
Bitrate 32Kbps ~ 10Mbps
Frame Rate 30 fps @ all resolutions
Streaming H.265 Dual Stream or Simultaneous H.265 / H.264 / MJPEG
Output HD-SDI repeated Video Out
Audio
Bi-Directional Audio Two way, full duplex
Audio Input Compression G.711
Audio Line Input Line level input. Nominal 0-dB input level is 1.0 VRMS.
Audio Output Compression G.711
Audio Line Output Line level output. Nominal output level is 1.0 VRMS.
External
I/O
Alarm Input (Digital Input) 1ch
Alarm Output (Digital Output) 1ch
Factory Default Button Restore to default setting (Network, Password and etc.)
RS422 (RS485) 1Ch. for External Device Control like a Serial Device (RS422-RS485
Auto-Sensing)
RS232 RS232C Level
SD Card SD Card Interface Support
USB Host 1 port, USB 2.0 Memory Stick
Network
Ethernet Ethernet(10/100 Based-T), Auto MDI
Protocol
TCP, UDP, IP, HTTP, DHCP, DNS, ICMP, ARP, IPv4 / IPv6, DDNS, NTP,
SNMP, Syslog, UPnP, Bonjure, ZeroConf, RTP/RTSP, Onvif, Genetec
Protocol
Software
Web Browser IE 8.0 or above
SDK Cellinx SDK 4.0
Security MD5 Password / iptables (firewall) / SSL
Operating Temperature 0°C ~ 40°C / 32°F ~ 104°F
Power Power Requirement DC 12V 1.0A / PoE (IEEE802.3af )
Power Consumption Max 8.0W
Physical Dimensions 169(W) x 117(D) x 31(H) mm
Weight / Material 400g / Aluminum
4

Connection
Basic connection
(1) POWER – DC 12V 1A
(2) ETHERNET - LAN cable (RJ45 jack), The opposite side is connected to the PC or
network device like HUB.
(3) Video Input – video signal by HD-SDI output (coaxial cable, BNC jack)
Expert connection
(1) RS232 : an external device control (ex. electronic display (board))
(2) Sensor (Alarm Input) : dry contact (N.O or N.C are available.)
(3) Alarm (Alarm Output) : relay switch (Nominal Voltage 5VDC, 1A)
(4) SD / SDHC card slot : 4GB~16GB SD / SDHC is available
(5) RS422 (RS485) : an external device control (PTZ driver ▶ TX + / - is used)
(6) MIC IN : microphone input
(7) LINE IN : Line Level input (Ø3.5 stereo jack, use amplified mic.)
(8) LINE OUT : Line Level ouput (Ø3.5 stereo jack, 8Ω)
(9) Video Output : for maintenance (BNC jack)
Device control
(ex. Display board)
PTZ control by RS422 (485)
Condensor Mic.
Amplified Mic. Amplified Speaker
Video Output
(for test)
Power
PTZ camera
(HD-SDI output)
5
CamPilot URH900A
Peripheral Connection
HUB

6
Connection
Network Connection Configuration Diagram
Camera
(HD-SDI output)
PTZ Camera
(HD-SDI output)
HUB
CamPilot URH900A
CamPilot URH900A
Router Router
Monitoring
PC
Monitoring
PC
(Coaxial Cable)
(LAN)
(LAN)
(LAN)
(LAN)
(WAN)
(WAN)
(Coaxial Cable)
(Coaxial Cable)
Internet
(Intranet)

7
Network
Setting an IP address
Change the network setting value with the program “NVTManagement”
1. NVTManagement execution
• Execute the file “NVTManagement.exe”
2. IP address set-up
• Click the button “Discovery”, select the model.
• Input the IP address, Subnet Mask, Gateway and DNS Server IP address, click the button
“Apply”
• If you don’t have a proper IP address, ask the network administrator.
| NVTManagement

8
Network
3. Accessing to CamPilot URH900A with a web browser
• Open a web browser on a monitoring PC and enter the IP address assigned to a CamPilot
URH900A as following
Example> http://192.168.1.2
• The page as below shows up after the connection is completed.
ID / Password :
root / pass (Initial Value)
Login button :
it enables you to move to the Web
Monitoring Page. On checking the
Setting box and clicking the button,
you can move to the Web Setting
Page.
Guest Login :you can move to the
Web Monitoring Page as “guest”
| Initial Access Page
| Web Monitoring Page
Refer to the document “URH900A_Web_Manual.pdf” for the Web server.