Cellinx CamPilot STH320 User manual

1
Full HD IP IR Dome Camera
CamPilot STH320
User Manual
CamPilot STH320
Before installing and using the product,
please read this manual carefully.
Be sure to keep it handy for later reference.
An adaptor and a LAN cable are not included in the product
Overview
Accessories
•1/3" Sony Exmor CMOS sensor
•x3 Optical Zoom Auto Focus(3mm~9mm)
•Day & Night (ICR) / WDR / DNR / HLC / De-Fog
•IR LED ( 22 EA)
•1920x1080 resolution at 30 FPS
•Multi-codec support : H.264 / MJPEG / MPEG4
•Multi-stream with variable resolution & frame
- 1st stream : H.264 or MJPEG @ 1080p~VGA
- 2nd stream : H.264, MPEG4 or MJPEG @ D1~CIF
- 3rd stream : H.264, MPEG4 or MJPEG @ CIF~QCIF
•Stream based motion detection
•Multi-codec audio support : G.711 / G.726
•Two-way audio supported (Full Duplex)
•Alarm Input (1ch) / Output (1ch)
•SD / SDHC card support
•Power : DC 12V / PoE (IEEE802.3af)
3 screws
for mounting
Dome cover
wrench
Pin connector
(2pins-power, 4pins-DIO)
Cable hole cover and
assembly hardware

2
Precaution
WARNING
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTIONS
■ Do not open or modify
Do not open the case, as it may be dangerous and cause damages.
■ Do not put objects inside the unit
Make sure that no metal objects or flammable substances get inside the camera. It could cause
fire, short-circuits or damages.
■ Be careful when handling the unit.
To prevent damage, do not drop the camera or subject it to strong shock or vibration.
■ Install away from electric or magnetic fields.
■ Protect from humidity, dust and high temperature.
An additional case that is temperature-controllable, damp-proof and waterproof is required for
outdoor use.
■ Cleaning
Dirt can be removed from the case only by wiping it with a soft cloth moistened with a soft
detergent solution.
■ Mounting Surface
The mounting surface material must be strong enough to support the camera.
■ CamPilot STH320 can be used for surveillance purpose.
Be thoroughly informed of related regulations prior to installation to ensure compliance with such
regulations

3
Overview
Features
STH320 is an IP camera that transmits real-time high-resolution digital video and audio
data with H.264 high compression rate over Internet or Intranet.
▶Body
▶Ceiling Mount Bracket
▶Wall Mount Bracket 1
▶Wall Mount Bracket 2
In case that the
cables are
installed inside
the wall
In case that the
cables are
installed along
the wall

4
Overview
Specification
Specifications
Device Sony Exmor CMOS
Size 1/3 inch
Resolutions 1080p/30fps, 720p/60fps
Active Pixels 1,936(H) x 1,105(V), 2.12MPixels
Min. Illumination Color : 1.0 lux , BW : 0.5lux
Color DSS : 0.002 lux , BW DSS : 0.001 lux
S/NRatio more than 50dB (AGCoff)
Shutter Speed 1/30(25) ~ 1/60,000 sec
Function
TDN/ DNR/ Defog / HLC/
Focusing Mode (Auto / One Push / Manual) / WDR/BLC(OFF/ WDR/ BLC) /
Privacy mask (Off / 24 positions)
Lens 3x Optical Zoom, f=3.0mm(wide) ~ 9.0mm(tele), F1.2 to F2.1
IRLED 22EA
Compression Type H.264(MPEG4 AVC) @L3.0 / MJPEG / MPEG4
Resolutions 1080p / 720p / D1 / 4CIF / VGA / CIF / QVGA / QCIF
Bitrate 32Kbps ~ 6Mbps
Frame Rate 30FPS @1920x1080p
Streaming H.264 Triple Streamor Simultaneous H.264 / MPEG4 / MJPEG
Bi-Directional Audio Two way, full duplex
Audio Compression G.711 / G.726
Audio Line Input Line level input. Nominal 0-dB input level is 1.0 VRMS.
Audio Line Output Line level output. Nominaloutput level 1.0 VRMS.
AlarmInput / Output 1 ch / 1ch
RS422 (RS485) -
Local Storage Micro SD/ SDHCCard support up to 32 GB
Reset Button Restore to default setting (Network, Password and etc)
Ethernet Ethernet(10/100 Based-T), RJ-45 Connector
Protocol
TCP, IP, HTTP, DHCP, FTP, DNS, DDNS, NTP, ICMP,
SNMP, SMTPE, UPnP, RTP, RTSP, Onvif
OS Embedded OS (Linux)
Web Browser IE8.0 or above
SDK Cellinx SDK 4.0
Security MD5 Password / iptables (firewall) / SSL
Operating Temperature TBD
Power Power Requirement DC12V / PoE(IEEE802.3af)
Physical Weight TBD
Case Material Aluninum(IP66)
Items
Video Compression
Software
Camera Module
Audio Streaming
Network
External I/O

5
Connection
1. Mounting and Assembling
Wall Mount Bracket 1 (DSB-210)
Wall Mount Bracket 2 (DSB-310)
Ceiling Mount Bracket (CPA-310)
Insert the cable onto the
mount and attach it on
the wall.
Assemble the dome-camera
installation mount
and insert the cable into the
mount.
Insert the cable into the
camera adaptor and
assemble it to the mount.
Connect the vandal dome camera.
Check the hole size as per vandal
dome series.
Connect the calbe in the Vandal
dome camera
and assemble the camera base
with the camera adaptor .
Attached the mount on to the wall
and insert the cable into
the mount and pipe.
After assemble the pipe
onto the mount, wrap the
teflon tape on the gap.
Assemble the adaptor
flange with the camera
adaptor and insert the cale into the
camera adaptor.

6
Connection
2. Connectors
•DC12V : Power (DC12V 1 A (or above) adaptor)
(If a PoE network device( by IEE802.3af) is used, it is not necessary to connect the power.)
•ETHERNET : LAN cable (RJ45 jack), The opposite side is connected to the PC or network
device like HUB.
•AUDIO : audio connection, Ø 3.5 jack
- OUT : Line Level ouput (Ø3.5 stereo jack, 8Ω)
- IN : Line Level input (Ø 3.5 stereo jack, use amplified mic.)
•DIO : Digital Input / Output
- IN : Digital input, dry contact (N.O or N.C are available.)
- OUT : Relay switch (A relayed equipment is required.)
3. IP address setup
•Refer to p.7~8 (Network)
▶Connectors

7
Network
Setting an IP address
Change the network setting value with the program “NVTManagement”
1. NVTManagement execution
• Execute the file “NVTManagement.exe”
2. IP address setup
• Click the button “NVT Scan”, select the model.
• Input the IP address, Subnet Mask, Gateway and DNS Server IP address, click the button
“Apply”
• If you don’t have a proper IP address, ask the network administrator.

8
Network
3. Accessing to CamPilot STH320 with a web browser
Open a web browser on a monitoring PC and enter the IP address assigned to a CamPilot
STH320 as following
Example> http://192.168.1.2
• The page as below shows up after the connection is completed.
ID / Password :
root / pass (Initial Value)
Login button :
it enables you to move to the Web
Monitoring Page. On checking the
Setting box and clicking the button,
you can move to the Web Setting
Page.
Guest Login :
you can move to the Web Monitoring
Page as “guest”
Refer to the document “STH320_Web_Manual.pdf” for the Web server.
< 초기 접속화면 >
▶The Initial Page
▶Web Monitoring Page