Cello W3203SH User manual

英文简易说明书
*）（

M3220G

1. Product Description
1.1 General
Introduction
Thank you for buying this Cello product, which is designed to give you many years of trouble-free
service.
You may already be familiar with using a similar unit, but please take time to read these
instructions. They are designed to familiarize you with the unit’s many features and to ensure you
get the very best from your purchase.
Safety is important
Your safety and the safety of others is important, Please therefore, ensure you read the “Safety
Instructions” before you operate this unit.
This display is a high performance display, it is controlled by MCU digital technology.
1.2 Contents
Please check all the following are in the Gift box before installing the product.
If any of the above items are missing, please contact the manufacture.
Important safety precautions
1.Please read all the instructions carefully before using this product.
2.Be sure to unplug when cleaning the LCD panel. Always clean with a special LCD panel cleaning
detergent.
3.Do not use accessories not authorised by the manufacture to prevent damage or risk of danger.
4.Do not disconnect the plug by pulling the power cable.
5.Do not use this display where it is likely to get wet, this to prevent damage or risk of danger.
6.The slits and openenings at the rear and bottom of the cabinet are there for ventilation to stop
componenents overheating. Do not block the vents with any type of soft materials such as a
blanket and place the monitor in a location with sufficient all round ventilation.
7. This display is equipped with a three pin power plug. The third pin is for the earth connection
and only applicable to sockets that are correctly earthed.
8. To prevent danger of electric shock do not remove the rear cabinet, all repairs should be done
by a qualified technician.
9. Place the display in a dry and well ventilated location.
a. Monitor including stand
b. HDMI cable
c. 12V / 4A Power pack
d. User manual
e. Warranty card

2
Mounted on wall Mounted on base
Block ventilation Block ventilation
ll ll
book case or embedded closet, unless such space is
well ventilated.
Thank you for buying this Cello product, which is designed to give you many years of trouble-free
service.
Please take time to read these instructions and familiarize yourself with this product.
Introduction
2. Installation and Connections
2.1 Display Installation instructions
2.2 Input signal connections
Connect the DP or HDMI cable to the
monitor and to the output DP or HDMI of
the connecting device. for example a PC.
2.3 Audio output
Supports headphone and external speaker.
This monitor also has built in speakers

Cursor up.UP
LEFT
RIGHT
DOWN
MENU
POWER
Press LEFT to decrease the value.
Press RIGHT to increase the value.
Button functions
Cursor down.
AUTO Press to go back to previous menu in the main Menu.
Press to change the source.
Press MENU to display the menu.
Press to confirm the selection in the main menu.
Press POWER to turn the monitor ON/ OFF (power).
The menu control buttons are shown as below, the button location my change according to
model but functions are the same.
When the display is working normally, the green indicator light is on; when the display is in
sleep mode (energy saving mode) the indicator light is red.

4
0 2
10 10 0
4 2kg
64kg
W*D*H
W*D*H
W*D*H
732 87mm×mm×440.3mm
826mm
×150mm×525mm

5
wer suppl management s stem
6. Instruction of Base Installation
Warranty
In the unlikely event that your product fails to work normally, please call the Cello Service team
on UK: 0333 433 0312, Rep Ireland: 0818 333 833 and they will provide you the services.
Mode er consumption
orking 48
0.5
1. Place the neck in position as shown, fix it with the supplied screws(ST4 x 14).(Figure 1)
2. Place the Ring(A) in position as shown.(Figure 2)
3. Put the stand to the neck of the TV set as shown below.(Figure 3)
4. Put the Ring(B) and fixing plate to the stand of the TV set as shown below.(Figure 4)
5. Attach the stand with the supplied screws(ST3 x 12).(Figure 4)
through aforesaid steps adv can remove the base.
4 x ST4 x 14
4 x ST3 x 12
Fixing plate B
Fixing plate A
(Figure 1)
(Figure 4)
(Figure 2) (Figure 3)

c of duct for
o ct i is u
n on
of W nic Products
In order to better care for and protect the earth, when this product is not needed any longe or its
service life is ended, please deliver it to a local plant with state-certified recycle and disposal
qualification pursuant to relevant laws and regulations on recycle and disposal of waste electric
and electronic products.