Central Pneumatic 47016 Assembly instructions

Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
ITEMS 47016 67181
20 oz. high volume, low pressure
gravity feed spray gun
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright©2002 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product
described herein. Tools required for assembly and service may not be included.
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-800-444-3353 as soon as possible.
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
Owner’s Manual & Safety Instructions
REV 12c
NOTICE
CLEAN IMMEDIATELY
Clean the Spray Gun
IMMEDIATELY after use.
Delayed or inadequate cleaning will
permanently clog the Spray Gun.

Page 2 For technical questions, please call 1-800-444-3353. Item 47016
67181
NOTICE
Clean the Spray Gun IMMEDIATELY after use.
Delayed or inadequate cleaning will permanently clog the Spray Gun.
Table of Contents
Safety .................................................2
Specifications .....................................5
Setup ..................................................6
Operation............................................9
Maintenance......................................12
Parts List and Diagram......................15
Warranty ............................................16
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY TO PERSONS
The warnings and precautions discussed in this manual cannot cover all possible conditions and
situations that may occur. It must be understood by the operator that common sense and caution
are factors which cannot be built into this product, but must be supplied by the operator.
WARNING – When using tools, basic precautions should always be followed, including the following:
Work Area
a. Keep the work area clean and well lighted.
Cluttered benches and dark areas
increase the risks of electric shock,
fire, and injury to persons.
b. Keep bystanders, children, and
visitors away while operating the tool.
Distractions are able to result in
the loss of control of the tool.
SAFETY OPERATION MAINTENANCESETUP

Page 3For technical questions, please call 1-800-444-3353.Item 47016
67181
NOTICE
Clean the Spray Gun IMMEDIATELY after use.
Delayed or inadequate cleaning will permanently clog the Spray Gun.
Personal Safety
a. Stay alert. Watch what you are
doing and use common sense when
operating the tool. Do not use the
tool while tired or under the influence
of drugs, alcohol, or medication.
A moment of inattention while operating the
tool increases the risk of injury to persons.
b. Dress properly. Do not wear loose clothing
or jewelry. Contain long hair.
Keep hair, clothing, and gloves away
from moving parts. Loose clothes, jewelry, or
long hair increases the risk of injury to persons
as a result of being caught in moving parts.
c. Do not overreach. Keep proper
footing and balance at all times.
Proper footing and balance enables better
control of the tool in unexpected situations.
d. Use safety equipment.
Wear heavy-duty work gloves and
a NIOSH-approved respirator
during use. Non-skid safety shoes
and a hard hat must be used for the
applicable conditions.
e. Always wear eye protection.
Wear ANSI-approved
safety goggles.
Tool Use and Care
a. Do not force the tool. Use the correct
tool for the application. The correct tool
will do the job better and safer at the
rate for which the tool is designed.
b. Disconnect the tool from the air source
before making any adjustments,
changing accessories, or storing the tool.
Such preventive safety measures reduce
the risk of starting the tool unintentionally.
Turn off and detach the air supply, safely
discharge any residual air pressure, and
release the throttle and/or turn the switch to
its off position before leaving the work area.
c. Store the tool when it is idle out of reach
of children and other untrained persons.
A tool is dangerous in the hands
of untrained users.
d. Check for misalignment or binding of
moving parts, breakage of parts, and any
other condition that affects the tool’s
operation. If damaged, have the tool serviced
before using. Many accidents are caused
by poorly maintained tools. There is a risk
of bursting if the tool is damaged.
e. Use only accessories that are identified
by the manufacturer for the specific
tool model. Use of an accessory not
intended for use with the specific tool model,
increases the risk of injury to persons.
Service
a. Tool service must be performed only
by qualified repair personnel.
b. When servicing a tool, use only
identical replacement parts.
Use only authorized parts.
c. Use only lubricants supplied with the
tool or specified by the manufacturer.
SAFETYOPERATIONMAINTENANCE SETUP

Page 4 For technical questions, please call 1-800-444-3353. Item 47016
67181
NOTICE
Clean the Spray Gun IMMEDIATELY after use.
Delayed or inadequate cleaning will permanently clog the Spray Gun.
Air Source
a. Never connect to an air source
that is capable of exceeding
200 psi. Over pressurizing the tool
may cause bursting, abnormal
operation, breakage of the tool or
serious injury to persons. Use only clean, dry,
regulated compressed air at the rated pressure
or within the rated pressure range as marked
on the tool. Always verify prior to using the
tool that the air source has been adjusted to
the rated air pressure or within the rated
air-pressure range.
b. Never use oxygen, carbon dioxide,
combustible gases or any bottled
gas as an air source for the tool.
Such gases are capable of explosion
and serious injury to persons.
SAVE THESE INSTRUCTIONS.
Symbol Definitions
Symbol Property or Statement
PSI Pounds per square inch of pressure
CFM Cubic Feet per Minute flow
SCFM Cubic Feet per Minute flow
at standard conditions
NPT National pipe thread, tapered
NPS National pipe thread, straight
Symbol Property or Statement
WARNING marking
concerning Risk of Eye Injury.
Wear ANSI-approved eye protection.
WARNING marking concerning
Risk of Respiratory Injury.
Wear NIOSH-approved respirator.
WARNING marking concerning
Risk of Explosion.
SAFETY OPERATION MAINTENANCESETUP

Page 5For technical questions, please call 1-800-444-3353.Item 47016
67181
NOTICE
Clean the Spray Gun IMMEDIATELY after use.
Delayed or inadequate cleaning will permanently clog the Spray Gun.
Specific Safety Instructions
1. Do not direct spray at people or animals.
2. Do not exceed maximum air pressure.
3. Do not spray near open flames, pilot lights,
stoves, heaters, the air compressor, or
any other heat source. Most solvents and
coatings are highly flammable, particularly
when sprayed. Maintain a distance of at least
25 feet from the air compressor. If possible,
locate the air compressor in a separate room.
4. Read all of the information concerning
coating products and cleaning solvents.
Do not use chlorinated solvents
(e.g. 1-1-1 trichloroethylene and
dichloromethane, also known as
methylene chloride) to clean spray guns.
Many spray guns contain aluminum,
which reacts strongly to chlorinated
solvents. Contact the solvent or coating
manufacturer as needed regarding
potential chemical reactions.
5. Industrial applications must
follow OSHA requirements.
6. Spraying hazardous materials may
result in serious injury or death.
Do not spray pesticide, acid, corrosive
material, fertilizer, or toxic chemicals.
7. Paints and solvents may be harmful or fatal if
swallowed or inhaled. Avoid prolonged skin
contact with solvents or paints as they will
irritate skin. After any contact, immediately
wash off exposed area with hot, soapy water.
8. Attach all accessories properly to the
tool before connecting the air supply.
A loose accessory may detach
or break during operation.
9. Install an in-line shutoff valve
to allow immediate control over
the air supply in an emergency,
even if a hose is ruptured.
10. Air hose fittings may get hot during use.
Allow fittings to cool before disconnecting.
11. WARNING: Some dust created by power
sanding, sawing, grinding, drilling, and
other construction activities, contains
chemicals known [to the State of California]
to cause cancer, birth defects or other
reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement or
other masonry products
• Arsenic and chromium from
chemically treated lumber
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and
work with approved safety equipment, such as
those dust masks that are specially designed
to filter out microscopic particles.
(California Health & Safety Code
§ 25249.5, et seq.)
WARNING: The brass components of
this product contain lead, a chemical
known to the State of California to cause
birth defects (or other reproductive harm).
(California Health & Safety Code
§ 25249.5, et seq.)
Specifications
Maximum Air Pressure 70 PSI
Air Inlet 1/4 IN. - 18 NPS
Cup Capacity 20 fl. oz.
Air Consumption 6 CFM @ 40 PSI
SAFETYOPERATIONMAINTENANCE SETUP

Page 6 For technical questions, please call 1-800-444-3353. Item 47016
67181
NOTICE
Clean the Spray Gun IMMEDIATELY after use.
Delayed or inadequate cleaning will permanently clog the Spray Gun.
Initial Set Up
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of
this product.
Note: For additional information regarding the parts listed in the following
pages, refer to the Assembly Diagram near the end of this manual.
Before Setup
1. This air tool may be shipped with a
protective plug covering the air inlet.
Remove this plug before set up.
2. Before first use, clean the Spray Gun using
a solvent-based thinner. If not removed,
the material used for testing and corrosion
prevention will contaminate paint.
Air Supply Setup
TO PREVENT SERIOUS INJURY FROM EXPLOSION:
Use only clean, dry, regulated, compressed air to power this tool.
Do not use oxygen, carbon dioxide, combustible gases,
or any other bottled gas as a power source for this tool.
1. Incorporate a filter, regulator with pressure
gauge, in-line shutoff valve, and quick coupler
for best service, as shown on Figure A on
page 7 and Figure B on page 8.
An in-line shutoff ball valve is an important
safety device because it controls the air
supply even if the air hose is ruptured.
The shutoff valve should be a ball valve
because it can be closed quickly.
Note: Do not use an automatic oiler system or
add oil to airline. The oil will contaminate the
material being propelled, ruining the final result.
2. Attach an air hose to the
compressor’s air outlet. Connect the
air hose to the air inlet of the tool.
Other components, such as a coupler plug
and quick coupler, will make operation
more efficient, but are not required.
WARNING! TO PREVENT SERIOUS INJURY
FROM ACCIDENTAL OPERATION:
Do not install a female quick coupler
on the tool. Such a coupler contains
an air valve that will allow the air tool to
retain pressure and operate accidentally
after the air supply is disconnected.
Note: Air flow, and therefore tool
performance, can be hindered by
undersized air supply components.
3. The air hose must be long enough to reach
the work area with enough extra length
to allow free movement while working.
4. Close the in-line shutoff valve between
the compressor and the tool.
5. Turn on the air compressor according to
the manufacturer’s directions and allow it
to build up pressure until it cycles off.
SAFETY OPERATION MAINTENANCESETUP

Page 7For technical questions, please call 1-800-444-3353.Item 47016
67181
NOTICE
Clean the Spray Gun IMMEDIATELY after use.
Delayed or inadequate cleaning will permanently clog the Spray Gun.
Figure A: Portable Air Supply Setup
C
A
E F
A
B
D
Description Function
A Air Hose Connects air to tool
B Filter Prevents dirt and condensation from damaging tool or workpiece
D Regulator Adjusts air pressure to tool
E Coupler and Plug Provides quick connection and release
C Air Cleaner / Dryer*Prevents water vapor from damaging workpiece
FAir Adjusting Valve*For fine tuning airflow at tool
*Optional components.
6. Adjust the air compressor’s output
regulator so that the air output is enough
to properly power the tool, but the output
will not exceed the tool’s maximum air
pressure at any time. Adjust the pressure
gradually, while checking the air output
gauge to set the right pressure range.
7. Inspect the air connections for leaks.
Repair any leaks found.
8. If the tool will not be used at this time,
turn off and detach the air supply and
safely discharge any residual air pressure
to prevent accidental operation.
Note: Residual air pressure should not be
present after the tool is disconnected from
the air supply. However, it is a good safety
measure to attempt to discharge the tool in a
safe fashion after disconnecting to ensure that
the tool is disconnected and unpowered.
SAFETYOPERATIONMAINTENANCE SETUP

Page 8 For technical questions, please call 1-800-444-3353. Item 47016
67181
NOTICE
Clean the Spray Gun IMMEDIATELY after use.
Delayed or inadequate cleaning will permanently clog the Spray Gun.
Figure B: Stationary Air Supply Setup
N
L
L O
M
C C
Non-lubricated
Tools
Lubricated Tools
H
I
I
J
JKH
F
G
E
Slope
F
F
B B
A A
CD
Description Function
A Vibration Pads For noise and vibration reduction
B Anchor Bolts Secures air compressor in place
C Ball Valve Isolates sections of system
for maintenance
D Isolation Hose For vibration reduction
EMain Air Line - 3/4″ min. Distributes air to branch lines
F Ball Valve To drain moisture from system
GBranch Air Line -1/2″ min. Brings air to point of use
H Air Hose Connects air to tool
Description Function
I Filter Prevents dirt and condensation
contamination
J Regulator Adjusts air pressure to tool
K Lubricator*For air tool lubrication
L Coupler and Plug Provides quick connection
and release
M Leader Hose*Increases coupler life
N Air Cleaner / Dryer*Prevents moisture contamination
OAir Adjusting Valve*For fine tuning airflow at tool
*Optional components.
SAFETY OPERATION MAINTENANCESETUP

Page 9For technical questions, please call 1-800-444-3353.Item 47016
67181
NOTICE
Clean the Spray Gun IMMEDIATELY after use.
Delayed or inadequate cleaning will permanently clog the Spray Gun.
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this
product.
Inspect tool before use, looking for damaged, loose, and missing parts.
If any problems are found, do not use tool until repaired.
Workpiece and Work Area Set Up
1. Designate a work area that is clean
and well-lit. The work area must not
allow access by children or pets to
prevent distraction and injury.
2. Route the air hose along a safe
path to reach the work area without
creating a tripping hazard or exposing
the air hose to possible damage.
The air hose must be long enough to reach
the work area with enough extra length
to allow free movement while working.
3. Before spraying, mask nearby
objects not being sprayed and lay
cloths (not included) on the floors.
Nozzle
Trigger
Lock Ring
Fluid
Knob
Pattern
Adjustment
Knob
Air Inlet
Air Knob
Cup
Figure C: Components and Controls
Spray Gun Setup Adjustment
TO PREVENT SERIOUS INJURY:
Do not adjust or tamper with any control or component in a way not specifically explained
within this manual. Improper adjustment can result in tool failure or other serious hazards.
CAUTION! Keep hands away from Trigger while making adjustments.
1. Thread the Cup to the top of the Gun Body
and tighten until the Cup is securely in place.
Note: This Spray Gun is meant for spraying
oil-based paints. It is not recommended for
regular wall paint or thin coatings of any type.
While these products can be used with
this Spray Gun, coverage will not be even.
Paint Preparation and Filling
Note: Proper paint mixture is essential.
Follow the manufacturer’s directions. Most paints
will spray easily if they are thinned properly.
2. Thin the paint according to manufacturer’s
directions and mix thoroughly.
3. Carefully strain the paint through
a paint strainer or a piece of cheesecloth.
SAFETYOPERATIONMAINTENANCE SETUP

Page 10 For technical questions, please call 1-800-444-3353. Item 47016
67181
NOTICE
Clean the Spray Gun IMMEDIATELY after use.
Delayed or inadequate cleaning will permanently clog the Spray Gun.
4. Fill the Cup to 3/4 full. Close Cup.
5. Start the air compressor and set
the regulator to needed pressure.
Do not exceed maximum air pressure.
6. Test the consistency by spraying
on a piece of scrap material.
If it still appears too thick, add a very
small amount of thinner (not included)
and mix thoroughly. Use the proper
thinner for the type of paint. Thin
CAUTIOUSLY. Proceed slowly,
adding minimal amounts at a time.
DO NOT exceed the manufacturer’s
thinning recommendations.
Fan Direction
7.
Figure D: Fan Direction
Horizontal Fan
Vertical
Fan
Nozzle
Lock Ring
To change the direction of the
fan from horizontal to vertical,
loosen the Lock Ring and turn the Nozzle 90°.
8. After the adjustment, tighten
the Lock Ring by hand.
Pattern Adjustment
WARNING! Do not exceed the Maximum Air
Pressure shown on the Specification chart.
9. Adjust the air supply pressure during
operation with the Trigger fully depressed and
the Air Knob fully open.
If reducing air pressure for specific areas,
use the Air Knob.
10. Use the Pattern Knob to
adjust the spray pattern.
Turn Pattern Knob counterclockwise
(all the way open) to flatten the spray pattern.
Turn it clockwise for a round spray pattern
- see Figure E: Pattern Adjustment.
Figure E: Pattern Adjustment
Flat/
Open
Round/
Closed
Fluid Adjustment
11. Turn the Fluid Knob clockwise
until it is fully closed.
12. After setting up a piece of scrap
material, squeeze the Trigger in short
bursts while turning the Fluid Knob
counterclockwise to set the amount of fluid
- see Figure F: Fluid Adjustment.
Too Fine
(Decrease
air flow)
Too Coarse
(Increase
air flow)
Correct
Figure F: Fluid Adjustment
If spray is too fine:
Reduce the air pressure or allow more paint
to come out by opening the Fluid Knob.
If spray is too thick (globs of paint):
Close the Fluid Knob slowly,
checking the pattern after each adjustment.
SAFETY OPERATION MAINTENANCESETUP

Page 11For technical questions, please call 1-800-444-3353.Item 47016
67181
NOTICE
Clean the Spray Gun IMMEDIATELY after use.
Delayed or inadequate cleaning will permanently clog the Spray Gun.
Spraying Technique
IMPORTANT: Proper spraying technique
is ESSENTIAL to achieve good results.
1. First, prepare the Spray Gun
according to the instructions under
Spray Gun Setup Adjustment on page 9.
2. Keep the Spray Gun upright and
at a right angle to the workpiece -
See Figure G and Figure H.
Figure G: Spray Gun Angle - top view
Incorrect
Gun
Angle Do not pivot your wrist
or wave the gun like a
fan towards the wall.
Move your arm, not just your wrist.
Point gun directly towards the surface and
maintain an even, steady distance and speed.
Correct Gun Angle
Figure H: Spray Gun Angle - side view
Correct Gun Angle Incorrect Gun Angle
3. Using two hands, one to steady the Cup
and the other to operate the Spray Gun,
aim Nozzle at the workpiece.
CAUTION: DO NOT STOP WHEN SPRAYING.
Spraying materials will start to set and dry
as soon as they come in contact with the air.
They will cause a permanent clog if not cleared
immediately. If discontinuing spraying for
more than half an hour, turn off the air supply,
disconnect Cup from Gun Body and thoroughly
rinse Cup and Gun Body with fresh, clean water.
4. Pull Trigger slowly and move Spray Gun
in parallel strokes to the workpiece.
Keep the distance from the workpiece
at about 6″to 9″, depending on the
flow adjustment and the paint.
5. To avoid paint build up, start moving the
Spray Gun before squeezing the Trigger.
When finished with the stroke,
release the Trigger while still moving
the Spray Gun - see Figure I. Doing this
will produce a smoother finish. Do not stop
moving the Spray Gun while spraying.
If the Spray Gun stops even briefly
while spraying the paint will build up
and run down the workpiece.
Figure I: Paint Stroke Triggering - top view
End
Stroke
Begin
Stroke
Release
Trigger
Squeeze
Trigger
Note: The stroke speed, the Fluid Knob
adjustment, and the distance from the workpiece,
will determine how much paint is being applied.
Apply two thin coats rather than one thick coat.
CAUTION! Air hose fittings may get hot.
Allow fittings to cool before disconnecting,
or wear gloves to prevent burns.
6. To prevent accidents, release trigger, detach
air supply, safely discharge any residual air
pressure, and again release trigger after use.
7. Clean Spray Gun thoroughly immediately
after EVERY use, according to
instructions on the following pages.
SAFETYOPERATIONMAINTENANCE SETUP

Page 12 For technical questions, please call 1-800-444-3353. Item 47016
67181
NOTICE
Clean the Spray Gun IMMEDIATELY after use.
Delayed or inadequate cleaning will permanently clog the Spray Gun.
User-Maintenance Instructions
Procedures not specifically explained in this manual
must be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY:
Detach the air supply and safely discharge any residual air pressure in the tool
before performing any inspection, maintenance, or cleaning procedures.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise, vibration, or leaking
air occurs, have the problem corrected before further use.
Inspection
Note: These procedures are in addition to the regular checks and maintenance
explained as part of the regular operation of the air-operated tool.
BEFORE EACH USE, inspect the general condition of the tool. Check for:
• loose screws,
• misalignment or binding of moving parts,
• clogged nozzle,
• damaged air supply hose,
• cracked or broken parts,
• damaged electrical wiring, and
• any other condition that may
affect its safe operation.
Cleaning
Solvent Selection
Follow the paint manufacturer’s
recommendations for cleaning, solvent type,
and disposing of used solvent.
•Latex Paints: Do not use
this Spray Gun with latex paint.
IMPORTANT: Do not use mineral spirits
on latex paints or the mixture will congeal,
making it very difficult to remove.
•Oil Based Paints: Use mineral spirits.
WARNING! TO PREVENT FIRE,
IF A FLAMMABLE SOLVENT
NEEDS TO BE USED,
ADHERE TO THE FOLLOWING:
a. Follow solvent manufacturer’s clean up
instructions and safety precautions.
b. Flush Spray Gun a full hose
length from air compressor.
c. If collecting flushed solvents in
metal container, transfer to nonmetal
container, and flush metal container.
d. Work far away from any ignition
sources in a vapor free area.
e. Keep class ABC fire extinguisher nearby.
After each use:
1. Empty the Cup and clean it with the solvent.
2. Fill the Cup with solvent and spray it through
the Spray Gun into a container, while shaking
the Spray Gun. Once the Cup is empty, repeat
the process until the solvent comes out clean.
3. Disconnect from the air source.
4. After disconnecting, point the Spray Gun into
the spent solvent container and squeeze the
Trigger again to make sure no air remains.
SAFETY OPERATION MAINTENANCESETUP

Page 13For technical questions, please call 1-800-444-3353.Item 47016
67181
NOTICE
Clean the Spray Gun IMMEDIATELY after use.
Delayed or inadequate cleaning will permanently clog the Spray Gun.
5. Remove Nozzle and soak it in solvent
until it is clean. Use old toothbrush
and toothpicks to remove any paint.
CAUTION: Do not immerse Spray Gun.
Note: Do not use metal objects to clean the
Nozzle to prevent damage to the passages.
6. Inspect fluid needle and make sure
it is not bent. If it is bent, have it
replaced by a qualified technician.
7. Use appropriate solvent
(see Solvent Selection, left)
to wipe down Spray Gun body.
8. Lubricate Spray Gun after cleaning.
A non-silicon oil or a light lubricant may be
used on threaded connections before storing.
Solution Disposal
After cleaning, dispose of cleaning solution
according to the solution manufacturer’s
directions and local hazardous waste standards.
Air Supply Maintenance
Every day, perform maintenance on the air supply according
to the component manufacturers’ instructions.
Storage
Store in a dry, secure area out of reach of children.
General Troubleshooting Chart
Problem Possible Causes Likely Solutions
Sputtering Spray 1. Low paint level.
2. Cup tipped.
3. Clogged Air Vent.
4. Loose fluid inlet connection.
5. Loose/damaged fluid tip/seat.
1. Refill.
2. Hold upright.
3. Clean Air Vent hole.
4. Tighten fluid inlet connection.
5. Adjust or replace fluid tip.
Will Not Spray 1. No pressure at Spray Gun.
2. Fluid Knob not open enough.
3. Fluid too thick.
1. Check air hoses.
2. Open Fluid Knob.
3. Thin fluid or increase air pressure.
(Do not exceed maximum.)
Overspray
(Paint drifting
to unintended
objects.)
1. Improper application speed.
2. Improper distance from workpiece.
3. Too much air pressure.
1. Move moderately and parallel.
2. Adjust distance.
3. Reduce air pressure.
Fluid Tip
Leakage
1. Dirty tip.
2. Broken fluid needle spring.
3. Worn or damaged tip.
1. Clean tip.
2. Replace fluid needle spring.
3. Replace tip and/or needle.
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect air supply before service.
SAFETYOPERATIONMAINTENANCE SETUP

Page 14 For technical questions, please call 1-800-444-3353. Item 47016
67181
NOTICE
Clean the Spray Gun IMMEDIATELY after use.
Delayed or inadequate cleaning will permanently clog the Spray Gun.
Problem Possible Causes Likely Solutions
Air Leaking
from Nozzle
1. Dirty air valve/seat.
2. Sticking air valve.
3. Damaged air valve spring.
4. Worn/damaged air valve/seat.
5. Bent valve stem.
1. Clean air valve/seat.
2. Lubricate air valve/seat.
3. Replace air valve spring.
4. Replace air valve.
5. Replace valve stem.
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect air supply before service.
Troubleshooting - Spray Pattern Diagnosis
Note: The drawings on the left below resemble symptoms of spray pattern problems.
Refer to the accompanying possible causes and likely solutions to the right.
Problem Possible Causes Likely Solutions
Heavy
center
pattern
1. Pattern Knob partially closed.
2. The paint is too thick.
3. The air pressure is too low.
1. Open Pattern Knob more.
2. Thin paint according to the
manufacturer’s instructions.
3. Increase air pressure within
the Operating Air Pressure.
Light
center
pattern
1. High air pressure.
2. Fluid Knob not open enough.
3. Pattern Knob open too far.
1. Reduce air pressure.
2. Open Fluid Knob.
3. Partially close Pattern Knob.
Heavy top/
bottom
pattern
1. Nozzle plugged.
2. Nozzle loose or dirty seal.
3. Dried paint on fluid tip.
4. Damaged Needle.
1. Clean Nozzle.
2. Clean and tighten Nozzle and seal.
3. Use a nonmetallic point
to clean Nozzle.
4. Have qualified technician
replace Needle.
Pattern
on right or
left only
1. Dirt on one side of fluid tip.
2. Holes on one side of
Nozzle are plugged.
3. Damaged Needle.
1. Clean fluid tip.
2. Clean Nozzle with nonmetallic point.
3. Have qualified technician
replace Needle.
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect air supply before service.
General Troubleshooting Chart (cont.)
SAFETY OPERATION MAINTENANCESETUP

Page 15For technical questions, please call 1-800-444-3353.Item 47016
67181
NOTICE
Clean the Spray Gun IMMEDIATELY after use.
Delayed or inadequate cleaning will permanently clog the Spray Gun.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Parts List and Diagram
Part Description Qty
1 Nozzle 1
2 Lock Ring 1
3 Ring Washer 1
4 Sealed Ring 1
5 Fluid Nozzle 1
6 Nozzle Seat 1
7 Nozzle Seat Gasket 1
8 Spacing Ring 1
9 Screw Washer 1
10 Washer 2
11 O-Ring 1
12 Gun Body 1
13 Screw 1
14 Washer 1
15 O-Ring 1
16 Air Valve 1
17 Valve Shaft 1
18 Valve Gasket 1
19 Switch Spring 1
20 Air Inlet 1
21 Fixing Screw 1
22 Adjustment Nut 1
23 Pattern Knob 1
24 O-Ring 1
Part Description Qty
25 Adjustment Seat 1
26 Split Washer 1
27 Needle 1
28 Needle Spring 1
29 Adjusting Knob 1
30 Adj. Knob Screw 1
31 Split Washer 2
32 Trigger 1
33 Trigger Pin 1
Part Description Qty
34 Needle Pin 1
35 Fluid Inlet Screw 1
36 Washer 1
37 Filter Connection 1
38 Connection Nut 1
39 Cup 1
40 Cup Lid 1
41 Vent Cap 1
15
7
34
8
32
31
2
33
9
19
12
45
1
3
6
10 11 10
18
20
17
21
16
14
13
39
36
22
23
24
25
26
27
28 29 30
37
35
40
41
38
SAFETYOPERATIONMAINTENANCE SETUP

3491MissionOaksBlvd.•POBox6009•Camarillo,CA93011•(800)444-3353
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER
OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE
BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE
MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS
REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS,
AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase.
This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence
or accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection verifies the defect, we will either repair or
replace the product at our election or we may elect to refund the purchase price if we cannot
readily and quickly provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted from causes not
within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.