Cerio FPOE-PE-E90 User manual

v1.6
FPOE-PE-E90
4Pair 90Watt Force Power Gigabit Edge PoE Adapters
User’s Guide
FCC Certifications
This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received; including
interference that may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class A for ITE,
the essential protection requirement of Council Directive 89/336/EEC on the approximation of the laws of the
Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible that information in this document
is not up-to-date. Please check with your local distributors for the latest information. No part of this document can be
copied or reproduced in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
Copyright © 2016, All Rights Reserved.
Unpacking Information
Thank you for purchasing our Force Power Edge PoE series products.
Before installation, please check that your package contains the
following items.
Open the shipping cartons of the Edge PoE Adapters and carefully
unpack its contents. The carton should contain the following
items:
1. FPOE-PE PSE (Unit1) x 1
2. FPOE-PE PD (Unit2) x 1
3. Inside diameter 2.1 (PHY) mm DC to DC cable x 1
4. 90W Power Adapter x1
5. Quick Installation Guide x 1
6. Warranty Card x 1
Hardware Overview
Introduction
The CERIO FPOE-PE-E90 is a Passive type Gigabit Edge PoE
Adapters. It provides DC 50-57V over Ethernet cables. Provides a
reliable hardware solution for demanding of 802.3bt Type3/Class5
45Watt
、
Class6 60Watt and Type4/Class7 72Watt
、
Class8 90Watt
PoE power level PoE/PD powered devices. Simultaneously transmit
network data and power to the PD equipment through the 4Pair UTP
Ethernet Cable transmission. This Force Power PoE++ Injector series
provides entry-level applications.
Functionality
The Cerio FPOE-PE-E90 are able to extend PoE to the Edge PoE
equipment (Such as small PoE Switch) to delivery power and data to
PD device through the 4Pair UTP Ethernet cable connecting the PSE
(Unit1) and PD(Unit2). Moreover, It’s compatible with IEEE 802.3bt
Type3 /Class5 45Watt、Class6 60Watt and Type4 /Class7 72Watt、
Class8 90Watt high power requirements PD device, such as the
"PoE IP Speed Dome PTZ CAM " and “the latest WiFi 6 generation
802.11ax WiFi AP provide a stable high power PoE powered solution.
Highlight Features
Supports 10/100/1000Mbps Gigabit Ethernet and
Complying with IEEE 802.3 10Base-T, IEEE 802.3u
100Base-TX, IEEE802.3ab 1000Base-T standard
Provides Force Power PoE++ output ability, and low
cable-loss which can maintain 90Watt PoE power up to
100 meters distance when using CAT 6 or up cabling
PSE Unit supports PSE/PoE function, max PoE output up
to 802.3bt Type4 Class 8 (90Watt) power level
PD Unit supports PD/PoE function, max PD power up to
802.3bt Type4 Class 8 (90Watt) power level when
bundle use with PSE unit
Supports ESD , Electro Static Discharge protection
includes Over Voltage protection and Short Circuit
Protection ensuring device safety
Some additional benefits of Cerio Force Power Gigabit
Edge PoE Adapters include cost saving, convenience in
network planning, and higher reliability.
Supports desktop, wall mounting installation and
multiple units combination easy to use

v1.6
Installation
Before Installation
Cerio Force Power Gigabit Edge PoE Adapters are able to
extend PoE to the Edge PoE equipment (Such as small PoE
Switch) to delivery power and data to PD device through the
4Pair UTP Ethernet cable connecting the Unit-1 and Unit-2.
Cables Installation
Cerio Force Power Gigabit Edge PoE Adapters can provide both
data and power for distances of up to 100 meters from the
power source (90Watt) and without cable-loss when using
CAT 6 or up cabling.
The setup of the Edge PoE Adapters can be performed using the
following steps:
Unit-1 ( PSE for Uplink Source and POE Downlink connection ):
Connect the included 90Watt power supply DC power Cable to
the “DC Jack Port” of Unit1
Connect your Ethernet cable (Cat6 or up cable) from your data
source to the “Data In port” of the Unit-1
Connect an Ethernet cable (Cat6 or uplink cable) from the "PWR
+ Data Output Port" of "Unit-1" to your “Unit-2” with an
extended distance (Max.100 meters) for Get power extension to
end device enable devices.
Unit-2 ( PD for POE receive and DC / DATA splitter connection ):
Connect “Power+Data” port on "Unit-2" and “PWR+ Data Out”
port form "Unit-1" with Ethernet cable, make sure “Power” LED
of "Unit-2" is on.
Connect “Power OUT” cable on "Unit-2" to power DC Jack of the
network end device and connect “Data OUT” cable on "Unit-2" to
RJ45 port of network end device. (Ex. Edge. POE Switch for end
POE Device such as POE IPCAM or POE WIFI AP )
Check whether the network device is LED on. If not, please make sure that
power is on for Unit-1 and Unit-2, and all cables are connected correctly.
Units Combination
This device can be locked on the wall, (Does not have screw
attachment, you must prepare it yourself) or it can be
combined with multiple units for easy to bundles organize the
Ethernet cables.
Product Application
Notice: Cable and Power Loss
@ 100Meter : Keep power source ability (90Watt) with Cat.6 or up Cable
@ 100Meter : “ 14Watt “ with Cat.5e Cable
Product Specifications
Standards & Hardware Specifications
Standard
IEEE802.3 10BASE-T
IEEE802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-T
Network Media
10BASE –T: UTP Cat. 3 or up
100BASE-TX: UTP Cat.5 or up
1000BASE-T: UTP Cat. 6 or up
Data Transfer Rate
10/100/1000Mbps (Half-duplex),
20/200/2000Mbps (Full-duplex)
PoE Type
Passive POE
Data PIN PIN 1/2, 3/6 & 4/5, 7/8
Power PIN
End-span (Type-A): PIN 1/2,3/6
Mid-span (Type-B): PIN 4/5,7/8
Ethernet Connector
RJ-45 x1 for Power + Data
RJ-45 x1 for Data
Power Connector DC Jack
ESD Protection
Over Voltage protection &Short Circuit
Protection
Environmental & Mechanical Characteristics
Max Power Output
90Watt
Power Requirement
56V 90Watt External Power Supply
PoE Input Voltage 50V~57V
Cable and Power
Loss
@ 100Meter : Keep power source ability
(90Watt) with Cat.6 or up Cable
@ 100Meter : “ 14Watt “ with Cat.5e Cable
LED Indicators
System LED: Power (Green) x1
Operating Temperature 0° to 55° C
Storage Temperature -40° to 70° C
Operating Humidity 5% to 90% non-condensing
Storage Humidity 5% to 90% non-condensing
Dimension 54 x 41 x 23mm ( W x D x H )
Unit Weight PSE Unit : 29.8g , PD Unit :29.8g
Case of Materials ABS
Production Location TW
Certification FCC, CE, RoHS-compliant