Chamberlain Secure home sh-9191au User manual

FEATURES

•Automaticallycomesonwhenmotionisde-

tected.

•Automaticallyturnslighto.

•Photocell keeps the light o during daylight

hours.

UNPACKING

Besuretoremoveallcontentsfrompackaging

andverifyallitemsarepresentbeforeassembling

thislightxture.ispackageincludesthefol-

lowingitems:

•Lantern

•MountingBracket(MountingBracketScrews

AreNotIncluded-Use4mmdia.(8G)x30mm

WoodScrews)

•Owner’sManual

REQUIREMENTS

•elightcontrolrequires230voltsAC.

•IfyouwanttouseManualMode,thecontrol

mustbewiredthroughaswitch.

•It is illegal for persons other than a licensed

electricianorpersonauthorizedbylegislation

to work on xed wiring or other electrical

installations.

Before installation, record the model num-

ber listed inside the xture. Attach receipt

in case of possible warranty issues.

Model Number:

Motion Sensing

Diecast Lantern

Lantern*

*Note:Illustrationsareforreferenceonlyandmay

bedierentfromactualproduct

Installation and Operating Instructions

Models: SH-9191AU, SH-9192AU,

and SH-9194AU

2201102-01

IMPORTANT SAFETY AND INSTALLATION INFORMATION

Beforeinstallingcoachlight,readallinstructionscarefullyandkeepowner’smanualforfuturerefer-

ence.

•

WARNING:Topreventelectricshock,pleaseensurethatpowerisdisconnectedbeforeinstallation.

•isxturemustbeconnectedtoa230V-240V~50Hzpowersource.

•exturemustbeproperlygrounded.

•isxtureisdesignedforoutdoorinstallationandshouldbemountedtoawall.

•Toachievebestresults,thisxtureshouldbemounted1.8meters(6feet)abovetheground.

•Donotusedimmerswitchesortimerswiththisxture.

esensoronthislightxturedetects“motion”bythemovementofheatacrossthecoveragearea.

However,followingareexamplesofobjectsthatalsoproduceheatandcancausethesensortotrigger:

•PoolsofWater •AirConditioners

•DryerVents •Animals

•HeatingVents •AutomobileTrac

Ifyoususpectthataheatsourceofthistypeistriggeringthesensor,reducethesensitivity.

esensoronthisxtureismoresensitivetothemovementofheatmovingacrossthecoveragearea

andlesssensitivetothemovementofheatdirectlytowardsit.

Least Sensitive Most Sensitive

Sensor

Motion Motion

201102-01

Bracket

Mounting

Screws (Not

Included)

INSTALLATION

This light xture must be installed by a

licensed electrician or other person autho-

rized by legislation to work on xed wiring

or other electrical installations.

IMPORTANT: Do NOT use with dimmers or

timers.

Forbestperformance,mountthextureabout

1.8meters(6feet)abovetheground.isxture

comeswithamountingbracket.Itispre-assembled

onthextureforshipping.

1. Removetwodecorativenuts.

2. Removemountingbracket.

3. Tightenxturemountingscrewsngertight

ontomountingbracket.

4. Positionmountingbracketagainstthewalland

markthepositionsforthemountingscrews.



Note:Makesurexture mounting screws are

paralleltothegroundbeforetighteningbracket

towall(seeFigure2).

5. Useapowerdrilltodrillintothewalltoprovide

asuitablemountingforthescrews.

•Bracketmountingscrewsarenotincluded.

Use4mmdia.(8G)x30mmwoodscrews.

•Careshouldbetakentoavoiddrillingor

screwingintoconcealedelectricalwiring.

•Forsolidbrickwalls,screwsandmasonry

plugsshouldbeused.

6.

Attachmountingbrackettowallwithaminimum

oftwoscrews.Note:Makesurexturemounting

screwsareparalleltothegroundbeforetighten-

ingbrackettowall(seeFigure2).

WARNING: Turn power o at circuit

breaker or fuse. Place tape over circuit

breaker switch and verify power is o at

the xture.

Note:Werecommendhavinganassistanthelphold

thelanternassemblyduringthewiringprocess.

Mounting

Bracket

Decorative Nut

Fixture

Mounting Screw

Fixture

Mounting

Screws

Mounting

Bracket

Figure 1

Figure 2

4201102-01

FINAL ASSEMBLY

1. Doublecheckallwiringconnections.

2.

Slidethextureassemblyontothemounting

screwsasshownonoutercartonpackaging.Make

surewiresdonotobstructmountingscrews

(see

Figure4)

3. Tightendecorativenutsremovedinstep1ofIn-

stallation sectionsecurelyagainstxturebase.

4. Caulkaroundxturebasewithsiliconeweather

sealant.IMPORTANT:Ensurethatthedrainhole

atthebottomoftheunitisnotblocked.

5. Installbulb.Do not exceed wattage rating on

xture label.

6. If applicable, install xture top using two

decorativescrews(seeFigure5).

WIRING

WARNING: Turn power o at circuit

breaker or fuse. Place tape over circuit

breaker switch and verify power is o at

the xture.

Terminal Block

From Fixture From AC Source

Green/YellowGreen/Yellow

Blue Blue or Black

Brow

ed or Brown

Figure 3

Wall

Mounting Bracket

Mounting Screw

Decorative Nut

Figure 4

Connectthexturewirestotheterminalblock

accordingtodiagram.Make sureallscrews on

terminalblockaretightenedsecurelyandterminal

blockinsulatorisfoldedoverterminalblock.

WARNING: Risk of electric shock.

Terminal block insulator must cover

terminal block after wiring is complete.

Terminal Block Insulator

201102-01

Decorative

Screw

Fixture Top

TESTING AND ADJUSTMENTS

1. Turn on the circuit breaker and light

switch.

Note:Sensorhasa11/2minutewarmupperiod

beforeitwilldetectmotion.Whenrstturned

onwait11/2minutes.

2. Set:

•ON-TIMEswitchtoTEST

•SENSITIVITYtoMid(M)position

3.

Walkthroughthecoverageareanotingwhere

youarewhenthelightsturnon.InTESTmode,

lightwillstayonfor5secondsaftermotionhas

stoppedandthenturno.

4.

Increaseordecreasethesensitivityasneeded.

Toomuchsensitivitymaycausefalsetriggering

duetoheatsourcesinthecoveragearea(see

Troubleshootingsection).

5. SettheamountofON-TIMEyouwantthe

lighttostayonaftermotionisdetected(1,5,

or10minutes).etimerwillresetaslong

asthereismotionpresent.Oncemotionhas

stopped, the timer will time-out after the

selectedamountoftime.

Figure 5

9.1 m

(30 ft.)

1.8 m

(6 ft.)

Maximum

Maximum Range Coverage Angle*

(Side View) (Top View)

180°

TEST 1 5 10 MIN

ON-TIME

LO - M - HI

SENSITIVITY

6201102-01

Note:Whenrstturnedonwaitabout11/2minutes

forthecircuitrytocalibrate.

*resetstoAutoModeatdawn.

OPERATION

MANUAL MODE

... back on.

1 Second

OFF then...

Manual mode only works at

night because daylight returns

thesensortoAUTO.

Flipthelightswitchoforone

second then back on to toggle

betweenAUTOandMANUAL

MODE.

Manualmodeworksonlywith

theON-TIMEswitchinthe1,

5,or10position.

SPECIFICATIONS

Range.................................................Upto9.1m(30ft.)[varieswithsurroundingtemperature]

SensingAngle.....................................Upto180°

ElectricalLoad...................................Seelabelonxtureformaximumwattagerating

BulbType...........................................E27ScrewBase,Type“A”

SensorCapacity..................................Upto360Watts(1.5A)maximumtungstenincandescent

PowerRequirements...........................230VAC,50Hz

OperatingModes...............................TEST,AUTO,andMANUALMODE

ON-Timer..........................................1,5,10minutes

TestTimer..........................................5Seconds

ManualModeTimer..........................Dusk-to-Dawn

IngressProtection...............................IP23

MANUAL MODE

AUTO

TEST

ON-TIME Switch at 1, 5,

or 10 minutes

MODE SWITCHING SUMMARY

Flip light switch

o for one second

then back on*

*Ifyougetconfusedwhileswitchingmodes,turn

thepoweroforoneminute,thenbackon.After

thecalibrationtimethecontrolwillbeintheAUTO

mode.

eChamberlainGroupreservestherighttodiscontinueproductsandtochangespecicationsat

anytimewithoutincurringanyobligationtoincorporatenewfeaturesinproductspreviouslysold.

Mode: On-Time Works: Day Night

Test 5Seconds x x

Auto 1,5,or10

Minutes x

Manual ToDawn* x

201102-01

SYMPTOM POSSIBLE CAUSE SOLUTION

Lightwillnotcome

on.

1. Lightswitchisturnedo.

2. Bulbislooseorburnedout.

3. Fuseisblownorcircuitbreakeristurnedo.

4. Daylightturn-oisineect.

5. Incorrectcircuitwiring,ifthisisanewinstallation.

1. Turnlightswitchon.

2. Checkbulbandreplaceifnecessary.

3. Replacefuseorturncircuitbreakeron.

4. Recheckafterdark.

5. Verifywiringiscorrect.

Lightcomesonin

daylight.

1. Light control may be installed in a relatively dark

location.

2. LightcontrolisinTEST.

1. e xture is operating normally under these

conditions.

2. SetON-TIMEswitchto1,5,or10minutes.

Lightcomesonfor

noapparentreason.

1. Lightcontrolmaybesensingsmallanimalsorautomobile

trac.

2. Sensitivityissettoohigh.

1. Reducesensitivity.

2. Reducesensitivity.

Lightstayson

continuously.

1. esensormaybepickingupaheatsourcelikeanair

vent, dryer vent, or brightly painted, heat-reective

surface.

2. LightcontrolisinManualmode.

3. Sensitivityissettoohigh.

1. Reducesensitivity.

2. SwitchtoAuto.

3. Reducesensitivity.

Lightasheson

ando.

1. LightcontrolisintheTESTmodeandwarmingup.

2. Heatbeingreectedfromotherobjectsmaybeaecting

thesensor.

1. Flashingisnormalundertheseconditions.

2. Re-aimsensor.Reducesensitivity.

TROUBLESHOOTING GUIDE

8201102-01

CHAMBERLAIN LIMITED WARRANTY

Lighting and Chime Products

ChamberlainAustraliaPtyLimited/Chamberlain NewZealandLimited(Chamberlain)is committed tomanufacturingandsupplyinghighquality goods.As

partofthiscommitment,weseektoprovidereliableserviceandsupportforourgoodsandarepleasedtoprovideyou,theoriginalpurchaser,withthisChamberlain

LimitedWarranty.

WealsoprovidethefollowingstatementasrequiredbytheAustralianConsumerLaw:InAustralia,inadditiontoyourrightsunderthisChamberlainLimitedWar-

ranty,ourgoodscomewithguaranteesthatcannotbeexcludedundertheAustralianConsumerLaw.Youareentitledtoareplacementorrefundforamajorfailureand

forcompensationforanyotherreasonablyforeseeablelossordamage.Youarealsoentitledtohavethegoodsrepairedorreplacedifthegoodsfailtobeofacceptable

qualityandthefailuredoesnotamounttoamajorfailure.

Chamberlain’s warranty

Chamberlainwarrantstotheoriginalpurchaserofthelightingorchimeproduct(includinganyLEDlightswhichareprovidedbyChamberlainaspartofthegoods)

(Unit)thattheUnitisfreefromdefectsinmaterialsandworkmanshipforaperiodof12monthsfromthedateofpurchase.

DuringtheapplicableChamberlainLimitedWarrantyperiod,ifyouareconcernedthattheUnitmaybedefective,contactyourretailerwhowillprovideyouwitha

replacementUnitorreferyoutoourservicecentreforafactoryrepairorreplacement.

Ifyourretailerrefersyoutous,callourservicecentreonthetollfreenumberbelowandaChamberlaintechnicianwilldiagnosetheproblem.Oncetheproblemhas

beendiagnosed,subjecttoyourrightsundertheAustralianConsumerLawwithrespecttomajorfailures,Chamberlainwillprovideyouwithshippinginstructions

forafactoryrepairorreplacement.

Ifafactoryrepairorreplacementisrequired,providedthedefectivepartorUnitisreturnedtoChamberlainwell-packagedandinaccordancewithChamberlain’s

shippinginstructions,Chamberlainwillrepairor,atitsoptionbutsubjecttoyourrightsundertheAustralianConsumerLawwithrespecttomajorfailures,replace

anydefectivepartorUnitandreturnittoyouatnocost.

RepairsandreplacementpartsprovidedunderthisChamberlainLimitedWarrantyareprovidedfreeofchargeandarewarrantedfortheremainingportionofthe

originalwarrantyperiod.

isChamberlainLimitedWarrantyprovidesbenetswhichareinadditiontoyourotherrightsandremediesasaconsumer.

Exclusions

Ifourservicecentredeterminesthatawarrantyclaimhasbeenmadeinrespectofafailureordefectarisingunderoroutofanyexclusiondetailedbelowsuchthatthe

claimisnotcoveredunderthisChamberlainLimitedWarranty,wemay,subjecttoyourotherrightsandremediesasaconsumer,chargeyouafeetorepair,replace

and/orreturntheUnittoyou.

Exclusions

isChamberlainLimitedWarrantydoesnotcoveranyfailureof,ordefectin,theUnitdueto:

1. non-compliancewiththeinstructionsregardinginstallation,operation,maintenanceandtestingoftheUnitorofanyproductwithwhichtheUnitisused;

2. anyattemptbyapersonotherthananauthorisedinstallertorepair,dismantle,reinstallormovetheUnittoanotherlocationonceithasbeeninstalled;

3. tampering,neglect,abuse,wearandtear,accident,electricalstorm,excessiveuseorconditionsotherthannormaldomesticuse;

4. problemscausedbyelectricalfaultsorreplacementofbatteriesorlightbulbs;

5. submersioninwaterorotheruids;

6. powersupplygreaterorlessthanwhatisspecied;

7. useofalightbulbwithahigherwattagethanthatspecied;or

8. forchimesproducts,radiointerferencefromanotherradiofrequencyappliance.

IfthisChamberlainLimitedWarrantydoesnotapply,youmayhaverightsavailabletoyouundertheAustralianConsumerLaw.

Liability – Australia only

ExceptassetoutintheAustralianConsumerLaw(beingSchedule2ofthe

Competition and Consumer Act 2010

)(asamended,consolidatedorreplaced):

1. allotherguarantees,warrantiesandrepresentationsinrelationtotheUnitoritssupplyareexcludedtotheextentthatChamberlaincanlawfullyexcludethem;

and

2. undernocircumstanceswillChamberlainbeliableforconsequential,incidentalorspecialdamagesarisinginconnectionwiththeuse,orinabilitytouse,theUnit,

otherthanthosewhichwerereasonablyforeseeableasliabletoresultfromthefailure.

Liability – New Zealand only

Exceptassetoutinthe

Fair Trading Act 1986

andthe

Consumer Guarantees Act 1993

(asamended,consolidatedorreplaced):

and

otherthanthosewhichwerereasonablyforeseeableasliabletoresultfromthefailure.

Note

Werequestthatyouretainyoursalesdocketorinvoiceasproof-of-purchaseandattachittothismanualtoenableyoutoestablishthedateofpurchaseintheunlikely

eventofawarrantyservicebeingrequired.ChamberlainreservestherighttochangethedesignandspecicationsoftheUnitwithoutpriornotication.Somefeatures

oraccessoriesoftheUnitmaynotbeavailableincertainmarketsorareas.Pleasecheckwithyourretailer.

Chamberlain service centre contact details

Australia New Zealand

Phonetollfree1800638234 Aucklandphone094772823

Faxtollfree1800888121 Phonetollfree0800653667

Email:customerser[email protected] Faxtollfree0800653663

Chamberlain Australia Pty. Ltd. Chamberlain New Zealand Limited

Unit 3, 7-9 Orion Rd 17A Arrenway Drive, Albany

Lane Cove NSW 2066 Auckland