Changhong Electric LED22D1000S User manual

TV
Operation Manual
Tel: [phone]
Fax: [phone]
Service E-mail: [email protected]
Web site: www.changhongeurope.com
CHANGHONG EUROPE ELECTRIC S.R.O.
Argentinská 286/38, 170 00 Praha 7, Czech Republic
FR
Z
I
EN
SK
T
C
DE C
H
AT/
( )
()
Model: LED22D1000S
22

Contents
Warning……………………………………………………………………..…..……… 1
E
nglish
Safety instructions……………………………………………………....…………… 3
Main Unit Control …………………………...…………..………..……..…………… 5
Front Panel ……….......................………………………………………….……... 5
Getting Started…………………………...………………………..……..…………… 7
Rear & Sides Panel …………........................................……………..………… 6
Using the remote control…………………………………………………….……... 7
Battery replacement……………………………..……………………….………… 7
Installing Batteries in the Remote Control……………………………..………… 7
Connection and Setup…………………...…………………………………………... 8
Cable Installation……………………………………………………………………. 8
Remote Control…………………………..…………………………………………… 9
Basic Operation……………………………………………………………………...11
Programme Selection…………….……………………………………………......11
Changing the Input Source…..…………………………………………………....11
Turning on and off the TV…………………………………………………………..11
Volume adjustment……………………………………………………………….....11
Menu Operation……………………………………………………………………….12
How to Navigate Menus…………………………………………………………....12
QUICK START GUIDE……………….………………………………………….….12
Configuring the Picture Menu……..……………………………………………….13
Configuring the Sound Menu…………..……………………………………..……14
Configuring the Channel Menu……………………………………………...……..15
Configuring the Time Menu ………...……………………………………………....17
Configuring the Setup Menu……..…………………………………………..….…18
Using USB mode………………………………………….………………….….… 22
Important Unique Buttons.................................................................................25
Channel List……………………………………………………………………….…25
EPG Weekly Mode ………....………………………….………………………..…25
Favorit List……..…………………………………………………………….....……25
Teletext…………………………………………………………………………...….....26
Using the teletext feature…………………........................................................26
Troubleshooting Guide……………………………………………………...….......27
Maintenance…………………………………………………………………...........28
Troubleshooting…………….………………………………………………...….....27

Warning
REGULATORY INFORMATION
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communication. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
CAUTION
DO not attempt to modify this product in any way without written authorization
from supplier. Unauthorized modification could void the user's authority to operate
this product.
It is not recommended to keep a certain still image displayed on the screen for a
long time as well as displaying extremely bright images on screen.
Figures and illustrations in this User Manual are provided for reference only
and may differ from actual product appearance. Product design and
specifications may be changed without notice.
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the products enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
E
ngli
sh
1

Warning
WARNING
To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To
Rain Or Moisture.
The ventilation should not be impeded by covering the ventilation openings with
items, such as newspapers, table-cloths, curtains, etc.
The Apparatus shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.
Attention should be drawn to the environmental aspects of battery disposal. Don’t
throw used batteries in dustbin. Please contact your retailer in order to protect the
environment.
When you install your TV, maintain a distance of at least 4 inches between the TV
and other objects (walls, cabinet sides, etc.) to ensure proper ventilation. Failing to
maintain proper ventilation may result in a fire or a problem with the product
caused by an increase in its internal temperature.
No naked flame sources, such as lighted candles, should be placed on the
apparatus.
To prevent the spread of fire, keep candles or other open flames away from this
product at all times.
The device may be malfunction when under electrostatic discharge. It can be
manually resumed by power off and power on again.
CAUTION connecting the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a
single outlet circuit which powers only that appliance and has no additional outlets
or branch circuits.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall
outlets, extension cords, frayed power cords, or damaged or cracked wire
insulation are dangerous. Any of these conditions could result in electric shock or
fire. Periodically examine the cord of your appliance, and if its appearance
indicates damage or deterioration, unplug it, discontinue use of the appliance, and
have the cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked upon. Pay particular attention to
plugs, wall outlets, and the point where the cord exits the appliance.
The MAINS plug is used as the disconnect device, and the disconnect device shall
remain readily operable.
Operating Temperature: 5°C to 35°C Operating Humidity: ≤80%
Storage Temperature: -15°C to 45°C Storage Humidity: ≤90%

This equipment is a Class Ⅱor double insulated electrical appliance. It has
been designed in such a way that it does not require a safety connection to
electrical earth.
E
nglish
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
2

Safety instructions
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
7. Do not block any of the ventilation
openings. Install in accordance with
the manufacturer's instructions.
5. Do not use this apparatus near water.
8. Do not install near any heat source
such as radiators, heat registers,
stoves, or other apparatus (including
amplifiers) that produce heat.
6. Clean only with a dry cloth. 9. Do not defeat the safety purpose of
the polarized or grounding type plug.
A polarized plug has two blades with
one wider than other. A grounding
type plug has two blades and a third
grounding prong. The wide blade or
the third prong is provided for your
safety. When the provided plug does
not fit into your outlet, consult an
electrician for replacement of the
obsolete outlet.
3
E
ngli
sh

Safety instructions
10. Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles,
and the point where they exit from
the apparatus.
13. Unplug this apparatus during
lightning storms or when unused for
long periods of time.
11. Only use the attachments/
accessories specified by the
manufacturer.
12. Use only with a cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the cart/
apparatus combination to avoid
injury from tip-over.
14. Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such as
power supply cord or plug is
damaged, liquid has been spilled or
objects have fallen into the
apparatus, the apparatus has been
exposed to rain or moisture, does not
operate normally, or has been
dropped.
ON DISPOSAL
-The fluorescent lamp used in this product contains a small amount of mercury.
-Do not dispose of this product with general household waste.
-Disposal of this product must be carried out in accordance to the regulations of
your local authority.
NOTE
-If the TV feels cold to the touch, there may be a small "flicker" when it is turned
on. This is normal; there is nothing wrong with TV.
-Some minute dot defects may be visible on the screen, appearing as tiny red,
green, or blue spots. However there has no adverse effect on the monitor's
performance.
-Avoid touching the screen or holding your finger(s) against it for long periods of
time. Doing so may produce some temporary distortion effect on the screen.
4
E
nglish

Front Panel
No. Name Description
1CH+/CH- Changes the channels.
2VOL+/VOL- Adjust the volume.
3MENU Open the menu.
4To switch among the signal source.
5Turns the unit on and off.
6 Power & Sensor Power Indicator and Infrared sensor.
6
Main Unit Control
5
E
ngli
sh
3
1
2
4
5

Rear & Sides Panel
Main Unit Control
No. Name Description
8
HDMI
Scart input/output.
10
AV AV audio/video signal input.
11
YPbPr YPbPr input.
12
PC input.
13
ANT1/2 Antenna input.
14
Ear phone output.
15
USB Connector for USB Play.
16 COMMON INTERFACE Insert CI card.
DIGITAL AUDIO OUT Digital audio output.
PC AUDIO/PC
9
Scart
HDMI input;
7
6
E
nglish
16
15
12
13
14
78 9 10 11

Getting Started
Usingtheremotecontrol
When using the remote control, aim it at remote sensor on the television. If there is an
object between the remote control and the remote sensor on the unit, the unit may not
operate.
Point the remote control at the REMOTE SENSOR located on the television.
When using this television in a very brightly lit area, the infrared REMOTE CONTROL
SENSOR may not work properly.
The recommended effective distance for using the remote control is about 7 meters.
Installing Batteries in the Remote Control
1. Open the cover at the back of the remote control.
2. Install two AAA size batteries. Make sure to match
the “+” and “-” ends of the batteries with the
diagram inside the compartment.
3. Replace the cover.
Batteryreplacement
You will need to install the batteries into the remote control to make it operate following
the instruction below.
When the batteries become weak, the operating distance of the remote control will be
greatly reduced and you will need to replace the batteries.
Notes on Using Batteries:
The use of the wrong type of batteries may cause chemical leakage and/or explosion.
Please note the following:
Always ensure that the batteries are inserted with the + and - terminals in the correct
direction as shown in the battery compartment.
Different types of batteries have different characteristics. Do not mix different types.
Do not mix old and new batteries. Mixing old and new batteries will shorten battery
life and/or cause chemical leakage.
Replace batteries as soon as they do not work.
Chemicals which leak from batteries may cause skin irritation. If any chemical matter
seeps out of the batteries, wipe it up immediately with a dry cloth.
The batteries may have a shorter life expectancy due to storage conditions. Remove
the batteries whenever you anticipate that the remote control will not be used for an
extended period.
The batteries (battery pack or batteries installed) shall not be exposed to excessive
heat such as sunshine, fire or the like.
CAUTION:
It may result in an explosion if batteries are replaced incorrectly.
Only replace batteries with the same or equivalent type.
7
E
ngli
sh

Connection and Setup
CableInstallation
installation and use.
1. Take out the TV from the package and put it in a drafty and flat place.
NOTE:
signal cable, please hold the plug
(the insulated part), do not draw the body of the cable.
2. The RF output terminal can be connected with the RF input port of the TV.
3. The output AV terminal of DVD can be connected with the AV input port of the TV
through AV cable.
NOTE:
4. The output COMPONENT (YPbPr) terminal of DVD can be connected with the
COMPONENT (YPbPr) input port of the TV through AV cable.
5. Connect one end of the VGA cable with the VGA port on computer, connect the other
end
each end of VGA cable.
NOTE:
the pin might be broken.
HDMI cable with the HDMI port on the TV.
NOTE:
the pin might be broken.
8. Sending the TV's audio signal to external audio equipment via the Digital Audio
Output port.
9. Check and make sure that all AV cables are connected with the corresponding ports
correctly.
10. Connect the power cable with 100-240V~ power supply.
NOTE:
The range of power input for the TV is 100-240V~ 50/60Hz; do not connect the TV
power input port with the power cable out of the above range.
not touch directly the metallic part of the cable.
Please read the relevant content in “Warning and Safety instructions” carefully before
the
When you plug or unplug the TV, computer or other equipment, you must make
sure that the power cable has been already shut down;
When unplugging the power cable or
Component and AV can not be used at same time for they share of one audio
channel.
of the VGA cable with the VGA port on the TV, and tighten the bolts clockwise on
the
While connecting the 15-pin VGA, please do not insert the plug overexerted, for
fear
6. Connect one end of the HDMI cable with HDMI output port; connect the other end of
the
While connecting the HDMI, please aim at carefully, do not insert overexerted, for
fear
Please hold the insulated part of the plug when you are unplugging the power cable,
do
If COMPONENT (YPbPr) and AV works as mini terminal, and shared same audio,
please choose to use a one-to-three audio&video cable.

7. Connect SCART socket input or output from an external device to these jacks.

8
E
nglish

Remote Control
The buttons of the original remote control are as following:
1. : Power, switch on or off TV set.
2. : Press to mute or restore sound.
3. II: Pause (in USB/PVR mode). Press
to enter the Time shift menu.
: MIX the teletext and signal in
teletext page.
4. : Stop (in USB/PVR mode).
: Hold the teletext page on display,
press again to release.
5. : Play (in USB/PVR mode).
: Enter the Teletext, press again
for MIX mode, and press this button
again to exit.
6. : Press button to start recording
(in DTV mode).
: Change size of teletext screen in
display mode.
7. : Previous (in USB mode).
i
: Go to the index page.
8. : Next (in USB mode).
?
:Reveal the hidden information of
some teletext pages.
9. : Fast reverse (in USB/PVR mode).
: Enter subtitle mode or subpage.
10. : Fast forward (in USB/PVR mode).
: Cancel the teletext but not to exit
teletext, press again to exit.
11. EPG: Electronic Programme Guide,
use in the DTV mode.
12. SUBTITLE: Select the subtitle
language of available.
13. INFO: Press to display the current
program information on the screen.
14. AUDIO: The button can be used to
switch between DUAL I/ DUAL II/
DUAL I+II/MONO/Stereo and switch
Audio language in DTV mode.
4 5 6
7 8 9
0
MENU EXIT
FAV
1 2 3
INFO EPG
12
3
6
7
4
5
8
910
11 12
13 14
15
16 17
18
19
20 21
22
23
24
25
26
27 28
LIST
CH
CH
SAT.LIST
9
E
ngli
sh

Remote Control
NOTE:
All pictures in this manual are examples, only for reference, actual product may differ
from the pictures.
The buttons not mentioned here are not used.
15. NUMBER BUTTONS: Choose channels
or password importation.
16. MENU: Press to enter the menu screen
for various optional adjustable settings.
17. EXIT: Exit OSD Menu.
18. ▲/▼/◄/►: To select the direction.
19. ENTER: Press to execute the selected
item in the menu screen.
20.
: Return to last viewed program.
21. SOURCE: Press to select signal source.
22. VOL+/VOL-: Press to adjust the volume
level up or down.
23. LIST: Press to call up the channel list.
Press again to exit it.
24. CH+/CH-: Press to select channels in
ascending or descending order.
25. COLOR BUTTONS: Red/ green/ yellow/
blue key navigation link.
USB: Press to enter the USB mode.
ANTENNA: Press to select an antenna
source.
SAT.LIST: Press to call up the satellite
list. Press again to exit it. (Satellite
signals only)
26. REC.LIST: Press to call up the record
list. Press again to exit it.
27. ZOOM: Press to select different images
sizes.
28. FAV: Press to call up the favorite list.
Press again to exit it.
4 5 6
7 8 9
0
MENU EXIT
FAV
1 2 3
INFO EPG
12
3
6
7
4
5
8
910
11 12
13 14
15
16 17
18
19
20 21
22
23
24
25
26
27 28
LIST
CH
CH
SAT.LIST
10
E
nglish

Basic Operation
TurningonandofftheTV
• Turn on the TV
Connect the power cable. If TV has a power switch, turn it on firstly. Press the
button on remote control can turn on TV from standby mode.
• Turn off the TV
Press the button on the remote control to enter standby mode.
Do not leave your set in standby mode for long periods of time. It is best to unplug the
set from the mains and aerial.
• No signal
There is No Signal menu on screen when there is no input signal. In ATV/DTV mode,
connected, the TV turns on automatically.
ProgrammeSelection
• Using the CH+/CH- on the panel of TV or on the remote control
Press CH+ to increase channel number.
Press CH- to decrease channel number.
• Using 0- 9 digital buttons.
You can select the channel number by pressing 0 to 9. (In DTV/ATV mode)
• Example
To select - channel (e.g. Channel 5): Press 5.
To select -- channel (e.g. Channel 20): Press 2 and 0 in a short time.
Volumeadjustment
• Press the VOL+/- button to adjust the volume.
• If you want to switch the sound OFF, press the .
• You can release mute by pressing the or increase the volume.
ChangingtheInputSource
You can select the input source by pressing the SOURCE button on the remote control.
Press the▲/▼button to cycle through the input source, and press the ENTER button to
confirm your choice.
if there is no signal in 5 minutes, the TV will turn off automatically. In PC mode, the TV
set will automatically turn off in 60 seconds if no input signals. When VGA cable is
11
E
ngli
sh

Menu Operation
HowtoNavigateMenus
Please before using the TV follow the steps below to learn how to navigate the menu in
order to select and adjust different functions. The access step may differ depending on
the selected menu.
1. Press the MENU button to display the main menu.
2. Press the▲/▼button to select the desired sub item.
3. Press the ►button to access the submenu.
4. Press the ▲/▼/◄/►button to select the desired value. The adjustment in the
OSD may differ depending on the selected menu.
5. Press the MENU button to return to the previous menu.
6. Press the EXIT button to exit from the menu.
NOTE:
When an item in MENU is displayed gray, it means that the item is not available or
cannot be adjusted.
Buttons on the TV have the same function as corresponding buttons on the remote
control. If your remote control is lost or couldn’t work, you may use the buttons on the
TV to select menus. This manual focuses on operation of the remote control.
Some items in the menus may be hidden depending on modes or signal sources
used.
QUICK START GUIDE
• Connection
1. Connecting the mains and antenna.
2. If TV has a power switch, turn it on firstly. Then press Power button on the
remote to turn on the TV.
• First Time Setup
When the TV is initially powered on, a sequence of on-screen prompts will assist in
configuring basic settings.
1. Language
Press the ▲/▼button to select the desired OSD (On Screen Display) language.
2. Demo Mode
Press the ▲/▼button to select On or Off.
3. Country
Press the ▲/▼button to select the country you want to.
4. LCN
Press the ▲/▼button to select On or Off.
5. Auto Sleep
Press the ▲/▼button to select the hours you want to.
6. TV Antenna
Press the ▲/▼button to select the method of TV connection: Air , Cable or Satellite.
8. Auto Scan
Press the ▲/▼button to select mode: All, ATV, DTV.
Press the ▲/▼button to select the signal type: T, T2, T+T2.
7. T/T2
12
E
nglish

Menu Operation
ConfiguringthePictureMenu
• Picture Mode
You can select the type of picture
which best corresponds to your
viewing requirements.
Brightness, Contrast, Sharpness,
Color and Tint (NTSC) can be
adjusted when the picture mode is
set to User.
The manufacture's
recommendation mode is
Home.
• Brightness
Adjusts the base level of the signal in the picture.
• Contrast
Adjusts the signal level between black and white in the picture.
• Sharpness
Adjusts the level of crispness in the edges between the light and dark areas of the
picture.
• Color
Adjusts intensity of all colors.
• Tint (Only in the NTSC mode)
Adjusts the balance between red and green levels.
• Color Temp
Press the ENTER button to access the submenu.
Select the color temperature of the picture, and press the ▲/▼button to select the
Standard, Cool, Warm and User.
R Gain, G Gain and B Gain can be adjusted when the Mode is set to User.
• Aspect Ratio
You can select the picture size which best corresponds to your viewing requirements.
• NR
Reduces screen noise without compromising video quality.
• Backlight
To control the brightness of the screen, adjust the brightness of panel.
• Energy Saving
Energy Saving can be adjusted when the Picture Mode is set to Home.
Switch the Energy Saving On or Off.
• PC Setup (In PC mode)
Press the ENTER button to access the submenu.
Auto Adjust: Adjust the image automatically.
H Position: Centre the image by moving it left or right.
V Position: Centre the image by moving it up or down.
Phase: Minimize horizontal distortion.
Clock: Minimize vertical stripes in the screen image.
13
E
ngli
sh

Menu Operation
ConfiguringtheSoundMenu
• Sound Mode
You can select a sound mode to
suit your personal preferences.
Bass and Treble can be adjusted
when the sound mode is set to
User.
• Bass
Adjust the bass effect. Increases
or decreases lower-pitched
sounds.
• Treble
Adjust the treble effect. Increases
or decreases high-pitched sounds.
• Balance
You can adjust the sound balance of the speakers to preferred levels.
• Surround
Switch the Surround On or Off.
• AVL (Auto Volume Level)
AVL automatically remains on the same level of volume if you change programmes.
Because each broadcasting station has its own signal conditions, volume adjustment
may be needed every time when the channel is changed. This feature allows users to
enjoy stable volume levels by making automatic adjustments for each program.
• SPDIF
You can select a desired SPDIF Output mode.
• AD Switch (In DTV mode)
This is an auxiliary audio function that provides an additional audio track for visually
challenged persons. This function handles the Audio Stream for the AD (Audio
Description), when it is sent along with the Main audio from the broadcaster.
Press the ENTER button to access the submenu.
When the mode is On, Volume can be adjusted by users.
• Audio Delay
Correct audio-video sync problems, when watching DTV and when listening to digital
audio output using an external device such as an audio receiver (-200ms~200ms).
14
E
nglish

Menu Operation
ConfiguringtheChannelMenu
• Channel Manager
Press the ENTER button to
access the submenu.
First press the ▲/▼button to
highlight the channel you want to
delete, lock, skip or swap.
Then press the red button to
delete the channel.
Press the green button to lock the
channel.
Press the yellow button to skip the
select channel. (Your TV set will
skip the channel automatically when using CH+/CH- to view the channels.)
Press the blue button to set the channel to swap, then press the ▲/▼button to move
it to the position you want to put.
• Favorite Manager
Press the ENTER button to access the submenu.
Press the ▲/▼button to select the items.
Press the CH+/CH- button to page up or down the Favorite list.
Press red, green, yellow, blue button to select the desired favorite group.
• Country
Select the country you want.
• Antenna
Select an antenna source.
• Auto Scan
Press the ENTER button to access the submenu.
When TV signals is Air.
All: Press the ENTER button to search the digital channels and analog channels.
DTV: Press the ENTER button to search the digital channels.
ATV: Press the ENTER button to search the analog channels.
NOTE: The TV will begin memorizing all of the available Channels. Once the
progress bar is full, the found channels will be stored and the unit will proceed to the
search for ATV, DTV, Radio and Date.
When TV signals is Cable.
All: Press the ENTER button to access the submenu.
– Scan Mode: Press the ▲/▼button to select scan mode: Blind Scan or Quick Scan.
Network ID and Frequency (KHz) can be adjusted when the Scan Mode is set to
Quick Scan.
– Network ID: Press the ◄/►button to select Network ID: Auto or enter digital
numbers.
– Frequency (KHz): Press the ◄/►button to select Frequency (KHz): Auto or enter
digital numbers.
– Start: Press the ENTER button to start search channels.
• T/T2 ( In Air mode)
T,T2,T+T2.
Select the signal type:
15
E
ngli
sh

Menu Operation
DTV: Press the ENTER button to search the digital channels.
– Scan Mode: Press the ▲/▼button to select scan mode: Full Scan or Quick Scan.
Network ID and Frequency (KHz) can be adjusted when the Scan Mode is set to
Quick Scan.
– Network ID: Press the ◄/►button to select Network ID: Auto or enter digital
numbers.
– Frequency (KHz): Press the ◄/►button to select Frequency (KHz): Auto or enter
digital numbers.
– Start: Press the ENTER button to start search channels.
ATV: Press the ENTER button to search the analog channels.
When TV signals is Satellite.
All: Press the ENTER button to access the submenu.
– Scan Mode: Press the ▲/▼button to select scan mode: Default, Network Search or
Blind Scan.
– Satellite: Press the ▲/▼button to select satellite names.
– Service Type: Press the ▲/▼button to select service type.: All Services or Free
Service.
– Channel Type: Press the ▲/▼button to select channel type: All or TV only.
– Start: Press the ENTER button to start search channels.
DTV: Press the ENTER button to search the digital channels.
– Scan Mode: Press the ▲/▼button to select scan mode: Default, Network Search or
Blind Scan.
– Satellite: Press the ▲/▼button to select satellite names.
– Service Type: Press the ▲/▼button to select service type.: All Services or Free
Service.
– Channel Type: Press the ▲/▼button to select channel type: All or TV only.
– Start: Press the ENTER button to start search channels.
ATV: Press the ENTER button to search the analog channels.
• DTV Manual Scan
Press the ENTER button to access the submenu.
When TV signals is Air.
Channel: Press the ▲/▼button to select the channel number.
Frequency (KHz): Display the frequency of current TV signal, or enter a user-defined
frequency.
BandWidth (MHz): Press the ▲/▼button to select the bandwidth.
Start: Press the ENTER button to start search channels.
When TV signals is Cable.
SymbolRate (KS/s): Press the ◄/►button to select SymbolRate: Auto or enter digital
numbers.
Modulation(QAM): Press the ▲/▼button to select Modulation: Auto, 16QAM, 32QAM,
64QAM, 128QAM or 256QAM.
Start: Press the ENTER button to start search channels.
Frequency (KHz): Display the frequency of current TV signal.
16
E
nglish

Menu Operation
• ATV Manual Scan
Press the ENTER button to access the submenu.
Current Channel: Press the ▲/▼button to select current channel.
Frequency: Display the frequency of current TV signal.
Scan: Press the ENTER button to enter scan, and then press ◄/►button to select
analog scan.
Fine Tune: Press the ENTER button to enter fine tune, and then press ◄/►button to
select fine tune.
Color System: Press the ▲/▼button to select Color System.
Sound System: Press the ▲/▼button to select Sound System.
Press red button to save it.
• LCN
Press the ▲/▼button to select LCN On or Off.
• Satellite System(Only In Satellite signal)
Press ENTER or ►to access the Satellite list.
• CI Information
Press ENTER or ►to access CI Information.
ConfiguringtheTimeMenu
• Auto Sync
Press the ▲/▼button to select
Auto Sync On or Off.
Set Auto Sync to Off, then you
can set the Date and Time
manually.
• Date
Press the number buttons to set
the date.
• Time
Press the number buttons to set
the time.
• Time Zone
Select your time zone.
When the Auto Sync is On, Time Zone can be adjusted by users.
• DST (Daylight Saving Time)
When Time Zone set to any time, this item is available to enable daylight saving option
or not.
• Sleep Timer
Select the time to turn the TV to standby mode automatically.
• Auto Sleep
Select the Auto Sleep time you want.
• OSD Timer
Select On-Screen Menu displaying time.
17
E
ngli
sh