Char-Broil TRU Infrared Patio Bistro 12601713 User manual

Assembly
Guide
GAS (LP)
(English)
42804703 • 7/5/12

2
CAUTION:
*SAFETY First…..Grill components may have sharp edges. Be careful when handling grill parts
during assembly. We suggest that you wear a sturdy pair of leather gloves while handling the grill parts.
BEFORE You Grill….
1.
2.
3. Pre– — 5 ,
TOOLS REQUIRED FOR ASSEMBLY
NOTE….
Phillips Head
(Not Supplied)
Small Adjustable
BEFORE You begin assembly of your grill….
1.
3.
2.
4.

Key Qty Description
A 1 GRILL BOTTOM
B 1 BURNER
C 1 HEAT SHIELD
D 1 CONTROL PANEL
E 1 HOSE VALVE REGULATOR
F 1 ELECTRODE
G 1 MATCH LIGHT COVER
H 1 MATCH HOLDER
I 1 ELECTRODE WIRE
J 1 FRONT LEG ASSEMBLY
K 2 FRONT LEG CAP
L 1 REAR LEG ASSEMBLY
M 2 REAR LEG CAP
N 1 COOKING GRATE
O 1 GREASE TRAY
P 1 WIND SHIELD
Q 1 WARMING RACK
R 1 TOP LID
S 1 LID HANDLE
T 2 LID BUMPER
U 1 TEMPERATURE GAUGE
V 1 BEZEL, F/ TEMPERATURE GAUGE
W 1 FLAME TAMER
X 1 CONTROL KNOB
Y 1 IGNITION MODULE
Z 1 REGULATOR HEAT SHIELD
AA 1 IGNITION HARNESS
NOT Pictured
… 1 HARDWARE PACK
… 1 ASSEMBLY GUIDE, ENGLISH
… 1 ASSEMBLY GUIDE, SPANISH - OPTIONAL
… 1 ASSEMBLY GUIDE, FRENCH - OPTIONAL
… 1 PRODUCT GUIDE, ENGLISH
… 1 PRODUCT GUIDE, SPANISH - OPTIONAL
… 1 PRODUCT GUIDE, FRENCH - OPTIONAL
… 1 GRILLING GUIDE, ENGLISH
… 1 GRILLING GUIDE, SPANISH - WEB ONLY
… 1 GRILLING GUIDE, FRENCH - WEB ONLY
… 1 GRATE CLEANING TOOL

R
C
A
E
F
VU
WB
S
Q
N
H
D
AA
I
O
L
J
M
M
K
K
X
4
P
Y
Z
G
T
T

Part Qty
A1– 1
A2–
Lower Body
1
A3– 1
Front Leg Assembly
Rear Leg Assembly
Fasteners
10-24x1/2"
(qty 4)
screw
5
A1
A2
Grill Lower Body Assembly
A2A3
A2

Fasteners
Grill Lower Body Assembly
6
(Qty 1)
10-24 Nut
10-24x3/8"
(qty 1)
screw
10-24 nut

GRILL IGNITION Assembly
7
Part Qty
B1– Electronic Ignition Module
B2– Battery
1
1
Electrode Wire
B2
B1

Fasteners
Complete Grill Lower Body Assembly
8
(Qty 2)
10-24 Nut
Part Qty
C1– 1
Heat Shield
C1

(qty 5)
Fiber Washer
(qty 3)
Fasteners
10-24x3/8"
(qty 3)
screw
10-24 Nut
(qty 2)
(qty 2)
1/4-20 Nut
screw
1/4-20x1"
GRILL LID Assembly
Part Qty
D1– Lower Body 1
D2– Wind Shield 1
D3– Grill Lid 1
D1
D2
D2
D3
9
D
10-24
Nuts
(3 each)
10-24x3/8”
Screws
(3 each)
Fiber
Washer
(3 each)
Fiber
Washer
(2 each)
1/4-20x1”
Screws
(2 each)
1/4-20
Nuts
(2 each)

4
10 GRILL FINAL Assembly
Part Qty.
E2 – 1
E3 –
Cooking Grate
1
E2
E3
E1 – 1
E1
E4
.
E4 – 1
Handle
Fasteners
(Qty 2)
Fiber Washer
10-24x3/8"
(Qty 2)
screw
E
Fiber washers
10-24x3/8” screws
Step 2 - With Grill Lid open, install the Handle (E4) to the lid. Insert fiber washer over 10-24x3/8”
screw from inside the lid through the lid holes, and into the handle. Repeat for other side - tighten
securely.
Step 1 - With Grill Lid open, screw Flame Tamer (E1) to burner. The place the Cooking Grate (E2)
into the Lower Body, allowing it to rest on the three brackets spaced around the Lower Body. The
cooking grate ridges should run from front to back of the grill as shown below. Place the Warming
Rack (E3) on to position by first hooking the center pin into the hole in the wind shield, then rotate the
warming rack down into position, with other pins secured in the slots.