Chargery C3060A User manual

© 2017 Chargery Power Co., Ltd. July 16, 2020
Add: Room 212-216, Zhongx ng Industr al Zone NanShan 518052 ShenZhen, Ch na
Tel: [phone], Fax: [phone], Email: [email protected]
C3060A/B v1.0
PFC programmable charger
High efficiency wide input voltage
90V~26 VAC Input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
T hanks for your purchasing the intelligent and powerful charger.
R ead the ENTIRE instruction manual to ecome familiar with the features/functions of the device
efore operating.
F eel free to send an email to j[email protected] or call at 86 755 2643 6165 should you have
any questions and suggestions.
Jason Wang

C3060A v1.0, C3060B V1.0
High efficiency wide input voltage
PFC programmable Charger
90V~26 VAC input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
www.chargery.com page 2 total 19
Features
The Battery Charger has been des gned to prov de rel able, qual ty charg ng for battery systems n
electr c dr ve veh cles. It s a h gh eff c ency w de nput voltage charger, the charger can output 1500W at
AC90V~265V n a smaller s ze. Many creat ve technology help to real ze up to 94% of eff c ency, and the
nternal temperature s st ll under 50℃. The follow ng are some new features:
 Intell gent control output voltage and current by m croprocessor, 100% cal brat on before
del very
 ±1% voltage and current accuracy
 Active PFC: smaller AC nput current less nterference, and Conform to European Comm ss on
Regulat on no 278/2009 and Energy Star Vers on 2.0
 AC 90-265V worldw de operat on: need not any alternat ve sw tcher, worldw de safe operat on.
 Low power consumpt on (less than 1W) at dle mode and standby mode
 Up to 94% of convert eff c ency.
 Programmable output voltage from 10V to 30V
 Programmable output current from 1A to 60A
 TFT color LCD d splay output Voltage, current, power and nternal temperature on t me.
 Over current, over voltage, over load, over temperature, and short c rcu t protect on
 Short-c rcu t protect on on output, safer and more rel able.
 2 Intell gent cool ng fans turned on and adjust speed upon the temperature automat cally
 ZVS/ZCS and Synchronous Rect f cat on assure the h ghest eff c ency.
 H gh power dens ty: 652W/Kg
 Start at no load or full load
 Approved by CE
 24 months warranty
Application
 Home appl cat on
 Electr c dr ve veh cles

C3060A v1.0, C3060B V1.0
High efficiency wide input voltage
PFC programmable Charger
90V~26 VAC input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
www.chargery.com page 3 total 19
Protection functions
1. Over current protection
2. Over voltage protection
3. Charge power protection
4. Over temperature protection
. Low battery voltage protection
6. Anti spark on battery connection even 100V battery connect to charger
7. Reverse polarity protection of battery connection
8. Prevent any cell from over charging, adjust charge current automatically fit with Chargery BMS
Main attery type and cell count
Battery
Type
Cell
Count
Output
Voltage/V
Terminal charge Voltage per cell
Charge
current
Terminal
charge
current/A
Charge
Mode
Min. Type Max.
LiPo 1S-7S 10-30 2.7 4.20 4.2
1.0-60A -60%
Pre-charge
CC/CV and
maintain
Li-ion 1S-7S 10-30 2. 0 4.10 4.1
LiFe 1S-8S 10-30 2.00 3.6 3.70
LiTo 2S-11S 10-30 1. 0 2.70 2.70
Pb 2S-12S 10-30 1.7 2.40 2. 0
- delta Voltage /mV
Min. type Max.
NiMH
/NiCd Auto 10-30 100 300 1000
CC

C3060A v1.0, C3060B V1.0
High efficiency wide input voltage
PFC programmable Charger
90V~26 VAC input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
www.chargery.com page 4 total 19
Warning
1. For any lithium battery, such as LiPo, LiFePO4, Li-ion, LiTo and other Li battery, the PCM
(Protection Circuit Module), BMS, cell monitor, saver etc. must be built-in the battery pack,
because the charger don’t monitor each cell voltage, even the total battery voltage don’t be
over charged, the single cell voltage is possible be over charged, special for larger impedance
cell. So if no PCM or BMS protect each cell from over charged, it is very dangerous.
2. Before charge, the cell count must be setup correctly, it is very important. Cell count is not the
cell quantity in a battery pack, it means cell count of connection in series, even cells
connected in parallel, the cell count is 1 NOT . Please according to your battery pack rated
voltage and the following table get the cell count.
Battery type, cell count and rated voltage ta le
cell count/Battery
rated voltage LiPo,V Li-ion,V LiFePO4,V
LiTo,V
P /VRLA/Gem
attery,V
1 3.8 3.7 3.2 2.4 2.0
2 7.7 7. 6.4 4.8 4.0
3 11. 11.2 9.6 7.2 6.0
4 1 .4 1 .0 12.8 9.6 8.0
19.3 18.8 16.0 12 10.0
6 23.1 22. 19.2 14.4 12.0
7 27.0 26.3 22.4 16.8 14.0
8 2 .6 19.2 16.0
9 21.6 18.0
10 24.0 20.0
11 26.4 22.0
12 24.0

C3060A v1.0, C3060B V1.0
High efficiency wide input voltage
PFC programmable Charger
90V~26 VAC input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
www.chargery.com page 5 total 19
Operation Instructions
1. Connect C3060A/B to AC 110 / 220V outlet by the spec al heavy power cable, f use other brand
cable, please note the w re AWG must be AWG14 at least.
2. Connect battery to charger.
3. Connect Chargery BMS8T to charger f poss ble.
4. 2 seconds later, the dle nterface s d splayed; the charger s ready to charge. Actual output voltage,
current and nternal temperature s also d splayed, but C3060A/B s at dle mode (no output) to save
power consumpt on.
5. Press knob shortly can choose Battery type; press aga n on
Battery type such as L Po can enter nto L Po charge setup
nterface. Here, you can setup cell count, charge current,
charge term nal current, and charge term nal voltage per
cell, and then press knob for 3 seconds start charg ng.
6. Stop charg ng, the battery voltage w ll goes down because
of self-d scharge, f need ma nta n battery voltage, please setup the Restart Charge YES (only for
C3060B), the charger w ll cont nue to charge when battery
voltage goes down to 5% of total battery voltage.
If set up to YES, the charger d splay KEEP after charge
f n shed.
If set up to NO, the charger d splay DONE after charge
f n shed.

C3060A v1.0, C3060B V1.0
High efficiency wide input voltage
PFC programmable Charger
90V~26 VAC input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
www.chargery.com page 6 total 19
7. Setup the charger work at Auto mode (only for C3060B),
F n sh all charge sett ngs, alternate Auto charge YES and press Knob for 3 seconds, the charger w ll
start to charge, and work at Auto mode n future t ll d sable t.
When the charger work at Auto mode, what you need to do s connect the AC power and battery to
the charger. The charger w ll operate at last sett ngs.
On Auto nterface, press Knob for 3 seconds alternate to Idle mode.
If need not charge as last settings, pleaser set up Auto Charge is NO
8. Dur ng charge, many charge nformat on s d splayed as below
9. S m lar w th L Po charge setup, you can setup L Io, L Fe, L To, Pb battery and N MH/N Cd.
10. At any t me Press knob shortly stop charg ng. The charger w ll work at dle mode to save power
consumpt on. Generally you needn’t d sconnect t from AC outlet, because t only consume under
1W power at dle mode.
Tips
 All parameters w ll be remembered by the C3060A/B t ll next change.
 Choose battery type, and press knob for 3 seconds start to charge at last setup
Battery voltage
Charge current
Capacity charged
Charge time
Internal temperature
Cell count, Battery Type, Charge status

C3060A v1.0, C3060B V1.0
High efficiency wide input voltage
PFC programmable Charger
90V~26 VAC input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
www.chargery.com page 7 total 19
Auto mode operation instructions
When you need charge same one battery repeat, you can set up Auto Charge s yes (Only for
C3060B), the charger w ll charge automat cally next t me, need not setup any parameters. At AUTO
charge, press Knob button shortly stop charg ng at any t me, and press t aga n start to charge. Or
dur ng charge, d sconnect battery stop charg ng, and connect t, start to charge aga n automat cally.
When need to charge new battery at d fferent parameters, d sconnect battery at AUTO nterface,
press Knob button for 3 seconds alternate dle nterface, the charger w ll work at ntell gent operate
mode, all parameters can be setup n th s mode.
for more deta ls about auto mode, Please watch the v deo on
http://www.chargery.com/V deo/C3060_Automode.mp4 .

C3060A v1.0, C3060B V1.0
High efficiency wide input voltage
PFC programmable Charger
90V~26 VAC input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
www.chargery.com page 8 total 19
Remote control charge Mode
COM1 is on the ottom of charger, connect to Chargery BMS, the charge current w ll be controlled by
BMS when any cell voltage reach OVP.
Battery connector s as below, two heavy term nal connect to battery pos t ve and negat ve separately,
there are two sl m term nal n m ddle of connector, t connect to external dev ce. The charge current can
be controlled by remote s gnal. The s gnal should be 1KHz 5V or 3.3V square
Note:
1. To real ze remote control charge by external dev ce, please purchase C3060A.
2. If don’t connect external dev ce, the charger can be operated by manual, f connect to the external
dev ce, and send a su table s gnal, after press Knob for 3 seconds start to charge, the charge current
w ll be adjusted accord ng to external s gnal. External s gnal can turn off charge (charge current s
zero, the charge status d splay KEEP), and control charge current at range 1A to 60A.
Warning
PWM s gnal adjust charge current, ncrease or decrease 10% max mal each
t me per one second.
Battery connector

C3060A v1.0, C3060B V1.0
High efficiency wide input voltage
PFC programmable Charger
90V~26 VAC input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
www.chargery.com page 9 total 19
Remote control operation instructions
1. Connect to AC source, turn on the charger
2. After f n sh n t al zat on, the C3060A enter nto dle model
3. Connect battery and external s gnal to the charger. Exclude battery
pos t ve and negat ve, the external s gnal must be connected to m ddle
two term nals. The battery voltage w ll be d splayed, but t s less than
battery voltage , t s normal, when start to charge, the battery w ll be
d splayed accurately.
4. Press Knob enter nto battery type nterface, alternate battery type and press Knob, enter nto
charge setup nterface,
a) Set up cell count,
b) Set up charge current, t should be the max mal current that the battery can be charged, when
PWM fa led, the charger w ll charge at th s current.
c) Set up end current. At CV phase (constant voltage), when the charg ng current s lower than
sett ngs, the charger stop charg ng and the battery fully charged, d splay KEEP charge status.
The end current s a percentage (1-60%) of charge current sett ng . Such as f the charge current
sett ng s 10A, end current s setup to 10%, the end current s 1A.
d) Set up end voltage, the voltage s cell voltage NOT battery pack total voltage, t must be under
or same as OVP on BMS. C3060A w ll charge at constant voltage when total battery voltage
reach cell count*setup value.
Note: On the charge mode, cannot setup restart charge and Auto charge.
9. Press Knob for 3 seconds, the charger w ll start to charge, the charge current w ll be mod f ed
accord ng to the Duty cycle of PWM from external dev ce. The h gher Duty cycle, the h gher current.
The current range s 1A-60A. need decrease the current, please decrease the Duty Cycle and then
ncrease t.
10. F n sh charge, the beeper sounds 10 t mes, charge current s zero, and d splay KEEP status. If need
cont nue to charge, adjust duty cycle to under 3% then ncrease gradually to adjust charge current,
start to charge aga n.
11. Dur ng charge, press Knob stop charg ng at any t me.
Please watch the operat on v deo on https://youtu.be/KDD-QWLkFQc

C3060A v1.0, C3060B V1.0
High efficiency wide input voltage
PFC programmable Charger
90V~26 VAC input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
www.chargery.com page 10 total 19
Program Setup
1. In charger dle nterface, press kno button for 2 seconds enter
nto Program Setup menu.
2. LCD d splay the follow ng nformat on n sequence and you can
mod fy ts value. When you want to alter a parameter value, press
the kno button make the value bl nk then mod fy the value by
rotate the button. The new value w ll be conf rmed and saved by
press ng the button aga n.
3. Press kno qu t the setup menu.
Note:
 All parameters w ll be remembered by the C3060A/B t ll next change.
Picture 3 Program setup
Setup the Temperature un t, ℃ or ℉, default ℃ .
Temp. Un t
---> ℃
Setup the max mal charge current, range from 1A~60A, step 0.1A, default
60A. It s only act ve for power supply.
Max current
---> 60A
Setup the fan start ng temperature, range from 30~50℃, step 1℃,
default 35℃. The fan speed will increase with the temperature go
up.
Fan ON Temp.
---> 40℃
The beeper sounds for each button press to conf rm your act on. These
sounds can be ON or OFF. Default ON.
Buzzer
---
>
ON
Th s menu sets the back-l ght t me of LCD screen backl ght.
Opt ons: 1MIN, 5MIN, 10MIN, 20MIN and Always on, default 5MIN. At
default 5m n, LCD back-l ght w ll be off to save the power, press kno
resume the ack-light.
BACK-LIGHT TIME
---> 5MIN
Setup over temperature protect on, range from 70~90℃, step 1℃,
default 8
0
℃
.
O
ver the temperature,
the
charge
r
will power off
Shut Down Temp.
---> 80℃

C3060A v1.0, C3060B V1.0
High efficiency wide input voltage
PFC programmable Charger
90V~26 VAC input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
www.chargery.com page 11 total 19
As power supply
On Battery type nterface, choose power supply setup output voltage
and max mal output current, the charger w ll work as a programmed
power supply; you can set up the output voltage and max mal output
current, and then press Knob for 3 seconds power on the charger.
 Output voltage adjustment range: 10V~30V,
 Output current adjustment range: 5A~60A.

C3060A v1.0, C3060B V1.0
High efficiency wide input voltage
PFC programmable Charger
90V~26 VAC input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
www.chargery.com page 12 total 19
Environment Requirements
 Amb ent Temperature : -10--45℃
 Amb ent Hum d ty ：5%--95%
 Storage Temp. ：-20℃--70℃
 Storage Hum d ty ：30%--90%
Input
 Rated Voltage ： AC110 / 220V
 Voltage allowed：AC90 ~ 265V
 Rated Freq. ：50/60Hz
 Freq. Allowed ：47~63Hz
 Max Current : 18A @90V, 7.5A @220V
 Eff c ency: 94% at 65% load and 220Vac nput.
 Act ve PFC: PF>0.99 at 90VAC and 100% of load; PF>0.97 at 220VAC and 100% of load
Output
 Voltage ：10 ~ 30V programmed
 Voltage accuracy: ±1%
 Current accuracy: ±1%
 R pple voltage: 150mV.
 Charge Current：1 ~ 60A
programmed
 Power: 1500W ma .
Protection
 Over voltage protect on, over 2V setup value.
 Under voltage Protect on, battery voltage s under 2V, don’t charge.
 Over current protect on, over 2A setup value.
 Over charge power protect on, 1500W max.
 Over temperature protect on, 90℃ max.
 Short- c rcu t protect on on output.
 Prevent any cell from over charg ng, adjust charge current automat cally f t w th Chargery BMS
Mechanical Characteristics
 S ze：278*145*68 (L*W*H, mm) or 10.8 * 6.7 * 2.7 (L*W*H, nch)
 We ght: 2.46Kg w thout nput cable
 Input power cable: AWG14 w re, 1.5m length
 Output DC connector: XT-90I male connector on C3060B or XT-90 male connector on C3060B

C3060A v1.0, C3060B V1.0
High efficiency wide input voltage
PFC programmable Charger
90V~26 VAC input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
www.chargery.com page 13 total 19
Packaging Information
 C3060A/B base un t: 1pcs
 Power cable: 1pcs
 Commun cat on w re: black, 1pcs
 XT-90 female connector: 1pcs, for C3060A
 XT-90I female connector:1pcs, for C3060B

C3060A v1.0, C3060B V1.0
High efficiency wide input voltage
PFC programmable Charger
90V~26 VAC input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
www.chargery.com page 14 total 19
Total solution on E-Vehicle application
Chargery BMS is a successful combination with the charger C3060. When all cell voltage reach setup
value, BMS communicate with charger, the charger continue to charge at a smaller current rather than
stopping charging.
It is very important at large current charge application. Because Start and Stop charging repeat by
Close or Open relay or MOSFET, not only cause battery voltage fluctuation at a large range, shorten
mechanical switch or electronic switch life, but also extend charging time notably.
Chargery BMS and charger as a total solution can charge and monitor each cell voltage, temperature,
charge and discharge current, short circuit even cell voltage difference, and charge each cell to any
voltage you want, such as you can set up the charge terminal voltage 3.8 V per LiPo cell, when charge
is done, the battery pack will be storage at safe status,
NOTE
Chargery charger decrease charge current according to “Over Charge Protection (P) Voltage” on BMS
setup, so please setup the charge terminal voltage in accordance with Over Charge Protection (P)
Voltage on BMS.

C3060A v1.0, C3060B V1.0
High efficiency wide input voltage
PFC programmable Charger
90V~26 VAC input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
www.chargery.com page 15 total 19
Error Information
When the follow ng error events tr gged, the beeper w ll sound for 10 seconds and error nformat on w ll
be d splayed, you can press kno utton turn off beeper sound and back up to Idle or auto mode
nterface.
Error information DESCRIPTION
Battery Vol. low No battery connection or reverse polarity of battery
connection or short circuit on output, the charger will be
power off
Battery Vol. High Battery voltage over setup, the charger will be power off
Over Current Output current over 2A of setup for 2 seconds, C3060A/B
turn off automatically and turn on manually
Over Voltage Output voltage over 2V of setup for 2 seconds, C3060A/B
turn off automatically and turn on manually
Over temperature The heat sink temperature over setup for 2 seconds,
C3060A/B power off automatically, and turn on manually
Connection Break At normal charge, disconnect battery, the charger will stop
charging, press Knob back up to idle interface
Warnings
 Never leave the charger unattended when t power on. If any malfunct on s observed, please
press Knob button power off the charger as fast as poss ble.
 Keep away the charger from dust, damp, ra n, heat d rect sunsh ne and v brat on. Do not drop t.
 The charger should be set up on non- nflammable and non-conduct ve surface. Never place on a
car seat, carpet or s m lar.
 Keep all the nflammable volat le mater als well away from operat ng area.
 Do not attempt to charge any L th um battery not bu lt- n BMS, PCM, cell voltage mon tor

C3060A v1.0, C3060B V1.0
High efficiency wide input voltage
PFC programmable Charger
90V~26 VAC input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
www.chargery.com page 16 total 19
Related parts
The follow ng parts are s m lar to the C3060A/B and maybe of nterest:
MODEL DESCRIPTION COMMENTS
C10325 4S-24S battery charger
BMS16T 2-16S battery management system
BMS24T 2-24S battery management system
S400 H gh eff c ency w de nput voltage PFC charger 10~130V 13.5A 400W output
S600 H gh eff c ency w de nput voltage PFC charger 10~18V 33A 600W output
S1200 H gh eff c ency w de nput voltage PFC charger 12~24V 50A 1200W output
S1500 H gh eff c ency w de nput voltage PFC charger 10~30V 60A 1500W output

C3060A v1.0, C3060B V1.0
High efficiency wide input voltage
PFC programmable Charger
90V~26 VAC input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
www.chargery.com page 17 total 19
Application Notes.
Storage Energy System
If C3060A/B charger appl ed to large capac ty energy System such as PV system, C3060A s suggested, the
charge current can be controlled by remote dev ce. The C3060A can rece ve PWM s gnal and adjust
charge current.
 The current range s 1A to 60A.
 When PWM duty cycle under 10%, C3060A w ll stop charg ng.
 When PWM s gnal fa l, the charger w ll charge at the sett ngs by manual.
E-car or other E- Vehicle
When C3060A/B appl ed to E-boat or other E- Veh cle battery, C3060B s suggested, and Auto charge
mode s the best, after setup all charge parameters and setup Auto Charge YES, the charger can charge
the battery automat cally at any t me. Need not any operat on bes des connect AC power source and
battery to the charger.
RC or UAV
When C3060A/B need charge mult ply chem stry battery, C3060B s suggested, on normal work mode,
the charger s easy to set up for all k nds of battery. It s enough flex ble to meet almost challenge.

C3060A v1.0, C3060B V1.0
High efficiency wide input voltage
PFC programmable Charger
90V~26 VAC input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
www.chargery.com page 18 total 19
Order information
Function Description
MODEL
C3060A C3060B
1. Remote control charge current by external device.
√
2. Start to charge automatically (Auto charge mode) after connect to AC
source and battery to charger
√
3. Restart charge when battery voltage drop -10%
√
4. Normal charge mode, Setup battery type, cell count and all charge
parameters
√ √
. Power supply mode, 12- V adjusted, 1- A adjusted
√ √
6. BMS control charge, Charge current controlled by Chargery BMS,
prevent any cell voltage from over charged
√ √
Version history
Version
V1.0 First released

C3060A v1.0, C3060B V1.0
High efficiency wide input voltage
PFC programmable Charger
90V~26 VAC input
For 7S LiPo, 8S LiFe battery
1~60Amps 1 00W max.
www.chargery.com page 19 total 19
Warranty and Service
Chargery Power Co., Ltd. as manufacture of R/C, E-Veh cle and UAV power warrants C3060A/B charger
to be free of defects n mater al and workmansh p. Th s warranty s effect ve for 12 months from date of
purchase. If w th n the warranty per od the customer s not sat sf ed w th the products performance
result ng from a manufactur ng defect, the accessory w ll be replaced or repa red. Th s warranty does
not cover the damage due to wear, m suse, ncompetent handl ng or us ng of ncorrect accessor es.
Chargery Power Co., LTD.
Tel: [phone] , fax: [phone]
Email: [e-mail]
Homepage: www.chargery.com