Charlton & Jenrick ES100 Quick start guide

Homeowner’s
Installation Instructions &
Operating Manual
Model: ES100
These Instructions cover Charlton & Jenrick
“E”Stove
Quality Products Produced by Charlton & Jenrick Ltd
Your product may differ slightly from this illustration
Please read the instructions carefully before installation or
use of this electric fire and retained for future reference.

APPLIANCE DATA
Supply Voltage AC 220-240V, 50Hz
Heating Element 2000W
Mains Cable 1 x 1.8m (approx)
TYPICAL FUEL BED ARRANGMENT
DIMENSIONS : Units in mm
IMPORTANT INFORMATION
Do not use this heater in the immediate surroundings of a bath, a shower or a
swimming pool.
This heater must be earthed. If in any doubt consult a suitable competent person.
In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this
appliance must not be supplied through an external switching device, such as a timer,
or connected to a circuit that is regularly switched on and off by utility.
This heater must not be located immediately below a socket-outlet.
Children shall not play with the appliance.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Cleaning and user maintenance shall not be carried out by children.
The Fuel bed contains some small glass beads which could be harmful to children if
swallowed, it is recommended that these are not used if children can access this
appliance
Some parts of this product can become very hot and cause burns. Particular attention
has to be given where children and vulnerable people are present.
The meaning of figure in marking is “WARNING: DO NOT COVER”.
If the power cord is damaged, it must be repaired by the manufacturer, its authorized
service centre or a professional person.

490
280
25
583
292.5
327
(490)
440 260
455
120
403
PARTS AND HARDWARE LIST
Part
Quantity
Stove with insert
1pc
Instruction Manual
1pc
Remote Control
1pc
AAA Battery
2pcs
Vermiculite
1pack
Clear Stones
1pack
Imitation Logs
4 pcs
INSTALLATION
NOTE:
Do Not use this Electric Stove if any part has been under water. Immediately call a
qualified service technician to inspect and to replace any part of the electrical system if
necessary. Keep plastic wrapping away from children.
Unpacking the heater carefully, make sure that the appliance is intact with no signs of
damage caused by transport. If in doubt, do not use the appliance and contact an
authorised service centre. Please save the original packaging as this may be required
in the event of a service complaint with the product.
Make sure that the plug or switched fused spur is accessible after the electric fire is
fitted.
If the supply cord is damaged, it must be replaced by a special cord or assembly
available from the manufacturer or its service agent.
Before connecting the appliance make sure that its rating corresponds to that of the
mains supply and the fuse is the correct rating.
The appliance should be located close to a suitable mains socket or fused spur to
enable connection and isolation. The electrical socket must be easily accessible to
allow disconnection.

Installation of stove:
Step1: Unpack and take away
the stove and parts.
Step2: Put the stove in the required position. Adjust feet
to ensure it is level.
Open the door of the stove and arrange the vermiculite,
clear stones and imitation logs on the plastic surface in
a pleasing arrangement of your choice. See Typical Fuel
Bed Arrangement for a guide
OPERATION
This appliance can be operated by both remote control and manual button. Once the
unit has been properly connected to an earthed electrical outlet, turn on the main
switch. A beep should be heard when the power is first applied.
NOTE: To use both remote and manual functions the main on/off switch must be
in ‘on’ position.
Operating by Manual Button
Flame Button
Heater Button
Main Switch
NOTE：The flame will always operate when the appliance is turned on.
Main switch
The main switch supplies power to all of the functions of the fireplace. This switch must
be in the “ON” position for any of the functions including the remote to operate.
Flame button
By pressing the FLAME button, the unit will cycle through four flame effects.
Heater button
Press once turns Fan on, and 10s later Low heat on. (Pilot lights illuminated●○)
Press again turns on High heat. (Pilot lights illuminated ●●)
Press third time turns heat off. 10s later fan off (Pilot lights illuminated ○○)
There are 3 levels you can cycle through including the OFF setting.

Multifunction Infrared Remote Handset.
To Reset the Heater
Your heater includes a protection system that shuts off the heater if it overheats for any
reason:
1) Turn unit to off.
2) Unplug unit wait 5 minutes.
3) Plug in and turn on.
●Operating by Remote Handset
In order to protect the product from becoming too hot, there is a 10s delay when
turning on the heater; also there is a 10s delay when turning off the heater fan.
Make sure the batteries are installed properly in the remote control.
The effective range of the remote control is up to 4 meters or 13 feet.
MAINTENANCE
Warning: Before any maintenance and/or cleaning the exterior of the
fireplace, disconnect the unit from the power supply and leave until cooled
off.
Remote Handset Battery Replacement
Replace with two AAA batteries. Make sure the batteries are installed correctly in the
remote control.
Maintenance of Motors
The motors used on the fan and flame effect are pre-lubricated for extended bearing life
and require no further lubrication. However, periodic cleaning/vacuuming of the
fan/heater unit is recommended.
ICON
TITLE
FUNCTION
POWER
Press once turns appliance and flame effects on. Press again
turns appliance and flame effects off.
FLAME
The fire has four flame effects, by pressing the flame effect
button the unit will cycle through each effect.
HEATER
Press once turns Low heat on. (Pilot lights illuminated●○)
Press again turns High heat on (Pilot lights illuminated ●●)
Press third time turns heater off. (Pilot lights illuminated ○○)
TEMP
Digital display shows the TEMP setting 23°C (default), with 14
settings circle from “OFF”, “16°C”to ”28°C”.
The TEMP will increase by 1°C up to 28°C when pressed each
time.
By pressing the TEMP for 3S, the digital display can show
between °C and °F.
TIMER
Cycles from OFF, 0.5H, 1H, 2H, 3H, 4H, 5H, 6H, 7H, 8H, to 9H.

Resetting the Thermal Cutout Switch
The appliance is fitted with an Electronic Safety Control (E.S.). This is a safety device,
which switches off the fire if, for any reason, the appliance overheats, e.g. when
covered. If the heater stops operating whilst the flame effect continues normally, this
indicates that the E.S. Control is in operation. The E.S. Control can only be re-set after
the appliance has cooled down, in order to re-set the E.S. Control proceed as follows:
Switch off the appliance (Manual On/Off switch) and leave for approximately
10-15 minutes.
Remove any obstruction to the fan heater outlet or fan blades etc. Make sure
that the power supply is disconnected at the plug socket outlet whilst you do
this.
Switch on appliance and the E.S. Control will re-set.
Ensure that the appliance is functioning correctly. If the E.S. Control operates
again, the appliance should be checked by a competent Electrician.
Cleaning the Fireplace
You can clean the exterior of the fireplace with a soft, damp, lint-free cloth. Do not use
cleaning or polishing products. To remove fingerprints or other marks on the front glass
panel, use a soft, damp, lint-free cloth with a good quality household glass cleaner. The
front glass panel should always be completely dried with a clean, lint-free cloth or paper
towel.
Caution: Do not use abrasive cleaners on the glass panel. Do not spray
liquids directly onto any surface of the unit.
Warning: An authorized service representative should perform any
other servicing.
Environment
Meaning of crossed –out wheeled dustbin:
Do not dispose of electrical appliances as unsorted municipal waste,
use separate collection facilities. Contact your local government for
information regarding the collection systems available. If electrical
appliances are disposed of in landfills or dumps, hazardous
substances can leak into the groundwater and get into the food
chain, damaging your health and well-being. When replacing old
appliances with new ones, the retailer is legally obligated to take
back your old appliance for disposals at least free of charge.
This appliance complies with the European Safety Standards (LVD) EN 60335-
2-30 and the European Electro Magnetic Compatibility (EMC) EN 55014-1, EN
55014-2 and EN 61000-3-2 and EN 61000-3-3 which covers the essential
requirements of the EC Council Directives and 2004/108/EC.