Masport FireGenie FG39-NG Quick start guide

01/06/05
PLEASE KEEP THESE INSTRUCTIONS
FOR FUTURE REFERENCE
Owners &
Installation
Manual
LISTINGSANDCODEAPPROVALS
These gas appliances have been
tested in accordance with AG 103,
NZS5262andhavebeencertifiedby
the Australian Gas Association for
installation and operation as
described in these Installation and
Operating Instructions.
Your unit should be serviced
annually by an authorised service
person.
918-280
Models: FG39-NG
FG39-LPG
Freestanding Gas Stove
Head Office - New Zealand
1-37 Mt Wellington Hwy.Panmure,
P.O. Box 14349
Auckland 6.
Australia
P.O. Box 533
Braeside, Victoria, 3195
WARNING:
Improper installation, adjustment,
alteration, service or maintenance can
cause injury or property damage. Refer to
this manual. For assistance or additional
informationconsultanauthorisedinstaller,
service agency or the gas supplier.
FORYOURSAFETY
Do not store or use gasoline or other
flammablevapoursandliquidsinthevicinity
of this or any other appliance.
Installation and service must be performed
byan authorisedinstaller, serviceagency or
the gas supplier.
FORYOURSAFETY
What to do if you smell gas:
Donottrytolightanyappli-
ance
Do not touch any electrical
switch: do not use any
phone in your building.
Immediately call your gas
supplierfromaneighbour's
phone. Follow the gas sup-
plier'sinstructions.
If you cannot reach your
gas supplier, call the fire
department.

2Masport FG39 FireGenie Freestanding Gas Stove
To the New Owner:
Congratulations! You are the owner of a state-of-the-art Masport Room Sealed Gas Stove by FPI Fireplace
ProductsInternationalLtd.TheMasportGasSeriesofhandcraftedapplianceshasbeendesignedtoprovide
youwithall thewarmthandcharmofawoodstove. ThemodelsFG39-NGandFG39-LPGofthisserieshas
beenapprovedbyAGA.Asitalsobearsourownmark,itpromisestoprovideyouwitheconomy,comfortand
security for many trouble free years to follow. Please take a moment now to acquaint yourself with these
instructions and the many features of your Masport Room Sealed Freestanding Gas Stove.
FG39-NG & FG39-LPG
UNIT SPECIFICATIONS

Masport FG39 FireGenie Freestanding Gas Stove 3
TABLE OF CONTENTS
Page Page
Operating Instructions
OperatingInstructions ............................................ 23
LightingInstructions ............................................... 23
ResettingtheUnit .................................................. 23
ShutdownInstructions............................................ 23
First Fire ................................................................ 23
FanOperation ........................................................ 23
AdjustingFlameHeight .......................................... 23
SummaryofControls ............................................. 24
Pilot Adjustment .................................................... 24
NormalOperatingSoundsof GasAppliances........ 24
CopyofLightingPlateInstructions ......................... 25
Maintenance
MaintenanceInstructions ....................................... 26
GoldPlatedDoors.................................................. 26
LogReplacement ................................................... 27
DoorGasket........................................................... 27
LatchAdjustment................................................... 27
GlassReplacement................................................ 27
FanMaintenance ................................................... 28
RemovingValve...................................................... 29
Replacement PartsList.......................................... 30
Warranty
Warranty ................................................................ 35
Safety Label
SafetyLabel............................................................ 4
Installation
Specifications ..........................................................5
BeforeYouStart ......................................................5
GeneralSafetyInformation ....................................... 5
InstallationChecklist ................................................6
ClearancestoCombustibles ....................................6
LocatingYourMasportGasStove ............................ 6
CombustionandVentilationAir ................................6
LouverInstallation.....................................................7
FlueingIntroduction ..................................................7
InstallationPrecautions ............................................7
SafetyPrecautionsfortheInstaller ...........................7
ExteriorFlueTerminationLocations .........................8
FlueingArrangements-Horizontal
Terminations: All Systems.................................9
FlueingArrangements-VerticalTerminations .......... 9
- Straight Vertical...............................................9
-OffsetVertical.................................................. 9
Flue Restrictor Position............................................9
DVStoveHorizontalFlue Kit .................................. 10
Dura-FlueTerminationKit....................................... 12
PlanningYourDura-FlueInstallation....................... 12
Dura-FlueFluingComponentsPartsList ................ 12
Dura-FlueHorizontalInstallation............................. 13
Dura-FlueVerticalTerminationInstallation.............. 14
OffsetChart............................................................ 15
CathedralCeilingInstallations ................................ 15
SupportExtension-RoundorSquare .................... 15
GasConnection ..................................................... 16
GasPipePressureTesting .................................... 16
ValveDescription ................................................... 16
AerationAdjustment............................................... 16
System Data Chart ................................................ 16
ConversionfromNGtoLPG ................................... 17
ConversiontoLowerBTU ....................................... 19
LogInstallation....................................................... 19
FrontDoorInstallation ............................................ 21
OptionalRemoteControl ........................................ 21
FinalCheck............................................................ 21
WiringDiagram ...................................................... 22

4Masport FG39 FireGenie Freestanding Gas Stove
SAFETY LABEL
This is a copy of the label that accompanies
eachMASPORTFG39FreestandingGasStove.
Wehaveprinted a copy of thecontents here for
your review. The data plat is located on the
inside of the drop down pedestal door.
NOTE: Masport units are constantly being im-
proved. Check the label on the unit and if there
isadifference,thelabelontheunitisthecorrect
one.
(AustraliaOnly)
Gas Type NG LPG
Model
Gas Consumption 40 . 38 .
Manifold Pressure .94 2.55
Injector Size 1x 1x 50
FG39-NG FG39-LPG
mj mj
kPa kPa
##
32
Electrical: 240VAC 50Hz 1.0 amp max.
Serial
Number
918-281
Model
N2134
Masport Gas Fireplace
2.95mm 1.78mm
AGA Approval number to
Code AG103 6240 6240
274
To be installed by an
authorised person in
accordance with
installation instructions
provided with the appliance
Masport Ltd.
1-37 Mt. Wellington H/Way
Auckland 6
New Zealand
Masport Pty. Ltd.
PO Box 533
Braeside, Victoria. 3195
Distributed by:

Masport FG39 FireGenie Freestanding Gas Stove 5
IMPORTANT:
SAVE THESE
INSTRUCTIONS
TheMASPORTRoomSealedFreestandingGas
Stove must be installed in accordance AG601
and NZS 5261 and with these instructions.
Carefullyreadalltheinstructionsinthismanual
first.Consult the building authority having juris-
diction to determine the need for a permit prior
to starting the installation.
Note: Failure to follow the instructions
could cause a malfunction of the
heater which could result in death,
serious bodily injury, and/or prop-
erty damage. Failure to follow
these instructions may also void
your fire insurance and/or war-
ranty.
Note: These instructions take prece-
dence over Simpson Dura-Flue in-
structions.
SPECIFICATIONS
Fuels: FG39-NG is approved for use with NG.
FG39-LPG is approved for use with
liquefied petroleum gases (LPG).
Electrical: 240V A.C. system.
Circulation Fan: Variable speed, 125/75.
Log Sets: Ceramic fibre, 7 per set.
Flue System: Coaxial (6-5/8" outer / 4" inner
liner) rigid flue and termination cap.
BEFORE YOU START
Safeinstallationandoperationofthisappliance
requires common sense, however, we are
required by the Canadian Safety Standards
and ANSI Standards to make you aware of the
following:
INSTALLATION
ING,ETC. ITISIMPERATIVETHAT
THECONTROLCOMPARTMENT,
BURNERSANDCIRCULATINGAIR
PASSAGEWAYS OF THE APPLI-
ANCEBEKEPTCLEAN.
DUE TO HIGH TEMPERATURES,
THEAPPLIANCESHOULDBELO-
CATED OUT OF TRAFFIC AND
AWAY FROM FURNITURE AND
DRAPERIES.
WARNING:FAILURETOINSTALL
THIS APPLIANCE CORRECTLY
WILLVOIDYOURWARRANTYAND
MAY CAUSE A SERIOUS HOUSE
FIRE.
CHILDRENANDADULTSSHOULD
BE ALERTED TO THE HAZARDS
OF HIGH SURFACE TEMPERA-
TURES, ESPECIALLY THE FIRE-
PLACE GLASS, AND SHOULD
STAY AWAY TO AVOID BURNS
ORCLOTHINGIGNITION.
YOUNG CHILDREN SHOULD BE
CAREFULLY SUPERVISEDWHEN
THEYAREINTHESAMEROOMAS
THEAPPLIANCE.
CLOTHINGOROTHERFLAMMA-
BLEMATERIALSHOULDNOTBE
PLACEDONORNEARTHEAPPLI-
ANCE.
INSTALLATION AND REPAIRS
SHOULDBEDONEBYANAUTHOR-
IZEDSERVICEPERSON.THISAP-
PLIANCESHOULDBEINSTALLED,
REPAIRED,INSPECTEDBEFORE
USE AND AT LEAST ANNUALLY
BYANAUTHORIZEDSERVICEPER-
SON. MORE FREQUENT CLEAN-
ING MAY BE REQUIRED DUE TO
EXCESSIVELINTFROMCARPET-
page 6. This unit is approved for manufac-
tured home installations, see page 9 for the
required flue arrangements. If installed into
a manufactured home the unit must be
bolted down to the floor.
4) This appliance is Listed for bedroom instal-
lations when used with a Listed Millivolt
Thermostat. Some areas may have further
requirements, check local codes before
installation.
5) This appliance is Listed for Alcove installa-
tions,maintain minimum Alcoveclearances
asfollows, minimumwidthof48"(1219mm),
a maximum depth of 36" (914mm), and
minimum ceiling height of 64"(1626mm).
6) We recommend that you plan your installa-
tion on paper using exact measurements
for clearances and floor protection before
actually installing this appliance. Have an
authorized building inspector review your
plans before installation.
GENERAL SAFETY
INFORMATION
1) The appliance shall be installed in accord-
ance with the manufacturer's installation
instructions,localgasfittingregulations,mu-
nicipal building codes, water supply regu-
lations, electrical wiring regulations, with
AG 601 (AGA gas installation code) NZS
5261 (New Zealand)
2) Installation and repair should be done
ONLY by an authorised person.
3) DONOTCONNECTTOMASONARYFLUE.
4) This appliance must be connected to
the specified flue and termination cap
to the outside of the building enve-
lope. Never flue to another room or
inside a building. Make sure that the
flue is fitted as per Flueing instruc-
tions.
5) Inspect the flueing system annually for
blockage and any signs of deterioration.
6) Flueing terminals shall not be recessed into
a wall or siding.
7) Any safety glass removed for servicing
must be replaced prior to operating the
appliance.
8) To prevent injury, do not allow anyone who
is unfamiliar with the operation to use the
fireplace.
9) Wear gloves and safety glasses for protec-
tion while doing required maintenance.
1) Provide adequate clearances for servicing,
proper operation and around the air open-
ings into the combustion chamber.
2) The appliance may be installed on a flat,
solid, continuous surface (e.g. wood, met-
al,concrete). This may bethe floor, orit can
be raised up on a platform to enhance its
visual impact. The appliance may be in-
stalled on carpeting, tile, wood flooring or
other combustible material, because the
appliance's metal pedestal base extends
the full width and depth of the appliance.
The Masport Room Sealed Freestanding
Gas Stove can be installed in a wide variety
of ways and will fit nearly any room layout.
It may be installed in a recessed position,
framed out into the room, or across a cor-
ner.
3) The Masport Room Sealed Freestanding
Gas Stove is approved for alcove installa-
tions, which meet the clearances listed on

6Masport FG39 FireGenie Freestanding Gas Stove
INSTALLATION
2) If required, adjusting the primary air to
ensurethattheflamedoesnotcarbon.First
allow the unit to burn for 15-20 min. to
stabilize.
CAUTION: Any alteration to the product
that causes sooting or carboning that
results in damage is not the responsibil-
ity of the manufacturer.
CLEARANCES TO
COMBUSTIBLES
TheclearanceslistedareMINIMUMdistances.
Measure the clearance to both the appliance
and the chimney connector. The farthest
distance is correct if the two clearances
do not coincide.
Forexample,iftheapplianceissetasindicated
in one of the figures but the connector is too
close, move the stove until the correct clear-
ance to the connector is obtained.
This appliance may be installed only with the
clearances as shown in the situations pic-
tured. Do not combine clearances from
one type of installation with another in
order to achieve closer clearances.
Thisunitcanbeinstalledonasolidcombustible
surface like a wood floor. This unit can also be
installeddirectlyoncarpeting orvinyl when the
bottom pedestal cover plate (provided with
unit) is installed.
Use the minimum clearances shown in the
diagrams below:
FG39-NG & FG39-LPG Clearances
A Side Wall to Unit 190mm
B Back Wall to Unit 150mm
E Side Wall to Unit 50mm
10)Be aware of electrical wiring locations in
walls and ceilings when cutting holes for
termination.
11)Under no circumstances should this appli-
ance be modified. Parts that have to be
removed for servicing should be replaced
prior to operating this appliance.
12)Installationandanyrepairstothisappliance
should be done by an authorised service
person. An authorised service person
should be called to inspect this appliance
annually. Make it a practice to have all of
your gas appliances checked annually.
13)Do not slam shut or strike the glass door.
14)Under no circumstances should any solid
fuels (wood, paper, cardboard, coal, etc.)
be used in this appliance.
15)The appliance area must be kept clear and
free of combustible materials, (gases and
other flammable vapours and liquids).
INSTALLATION
CHECKLIST
1) Check Clearances to Combustibles (page
6), location of unit (page 6) and fluing
requirements (pages 8 to 10).
2) Install Louvers, page 7.
3) Install fluing, either with the DV Stove Hor-
izontal Flue Kit (page 10) or the Dura-Flue
Terminationkits(page12).SetFlueRestric-
tors, page 9.
4) Make gas connections, page 16. Test the
pilot. Must be as per diagram.
5) If necessary, convert to LPG (page 17) or
convert to lower Btu rating (page 19).
6) Test Gas Pressure, page 16.
7) Install log set, see page 19.
8) Install Front Door Front, page 21.
9) Install optional Remote Control, page 21.
10)Final check, page 21.
Before leaving this unit with the customer, the
installer must ensure that the appliance is firing
correctly and operation fully explained to
customer.
This includes:
1) Clockingtheappliancetoensurethecorrect
firing rate (rate noted on label) after burning
appliance for 15 minutes.
FG39-NG & FG39-LPG
Reference Dimensions
C Back Wall to Flue Centerline 11" / 280 mm
D Side Wall to Flue Centerline 521mm
F Side Wall to Flue Centerline 280 mm
Minimum ceiling
height is 914 mm
from top of unit.
LOCATING YOUR
MASPORT GAS STOVE
When selecting a location for your stove,
ensure that the clearances listed above are
met as well as ensuring that there is adequate
accessibility for servicing and proper opera-
tion.
A) Cross Corner
B) RoomDivider
C) Island
D) Flat on Wall
E) Flat on Wall Corner
F) Flush with Wall/ Alcove
ForFlueTerminationrequirements,seepage8.
COMBUSTION AND
VENTILATION AIR
Thecombustionairfromthisapplianceisdrawn
fromoutsidethebuildingthroughtheouterflue.
Extra provision for combustion air inside
the room is not required.
12’ (4m)
A
C
D
E
F
B
12’ (4m)
Max.
Max.

Masport FG39 FireGenie Freestanding Gas Stove 7
LOUVER
INSTALLATION
1) Attachthetop&bottomlouvrestothe
side stove panel using 2 screws per
side.
INSTALLATION
FLUEING
INTRODUCTION
TheDVStoveHorizontalFlueKitandtheSimp-
sonDura-FlueRoomSealedSystemModelDV-
GS fluing systems, in combination with the
MasportRoomSealedFreestandingGasStove,
FG39-NG, and FG39-LPG, have been tested
and listed as direct flue heater systems by
AGA.
Theseunitsusethe"balanced flue" technology
Co-Axial system. The inner liner flues products
of combustion to the outside while the outer
pipe draws outside combustion air into the
combustion chamber thereby eliminating the
needtouseheatedroomairforcombustionand
losing warm room air up the chimney.
Note: These flue pipes must not be con-
nected to any other appliance.
The gas appliance and flue system must be
flueeddirectlyto theoutsideofthebuilding,and
never be attached to a chimney serving a
separate solid fuel or gas burning appliance.
Eachdirectfluegasappliancemustuseit'sown
separate flue system. Common flue systems
are prohibited.
IMPORTANT
Read all instructions carefully before starting
the installation. Failure to follow these instruc-
tions may create a fire or other safety hazard,
and will void the warranty. Be sure to check the
fluing and clearance to combustible require-
ments.Consultyourlocalbuildingcodesbefore
beginning installation.
The location of the termination cap must con-
form to the requirements in the Exterior Flue
Termination Locations diagram on page 8.
INSTALLATION
PRECAUTIONS
These fluing systems are engineered products
that have been designed and tested for use
with the FG39-NG, and FG39-LPG. The war-
ranty will be voided and serious fire, health or
other safety hazards may result from any of
the following actions:
1) Installation of any damaged Room Sealed
component
2) Unauthorized modification of the Room
Sealed System
3) Installationofanycomponentpartnotman-
ufactured or approved by Simpson Dura-
FlueorFPIFireplaceProductsInternational
Ltd.
4) Installation other than as instructed by
SimpsonDura-FlueandFPI FireplaceProd-
ucts International Ltd.
Warning: Alwaysmaintainrequired
clearances (air spaces) to nearby
combustibles to prevent a fire haz-
ard.Do notfill airspaces withinsu-
lation.
Besure to check theflueterminationclearance
requirements from decks, windows, soffits,
gas regulators, air supply inlets and public
walkways as specified in the Exterior Flue
Terminal Locations on page 8 and in your local
building codes.
The gas appliance and flue system must
be flueed directly to the outside of the
building, and never be attached to a chim-
ney serving a separate solid fuel or gas-
burning appliance. Each direct flue gas ap-
pliance must use it's own separate flue sys-
tem. Common flue systems are prohibited.
SAFETY
PRECAUTIONS FOR
THE INSTALLER
1) Wear gloves and safety glasses for
protection.
2) Exercise extreme caution when us-
ing ladders or on roof tops.
3) Be aware of electrical wiring loca-
tions in walls and ceilings.

8Masport FG39 FireGenie Freestanding Gas Stove
INSTALLATION
EXTERIOR FLUE TERMINATION LOCATIONS
Minimum clearances required for balanced flue terminals or
the flue terminals of outdoor appliances
according to AG 601 (AGA gas installation code) or NZS 5261 (New Zealand)
Minimum
Clearance (mm)
a Below eaves, balconies or other projections:
- Appliances up to 50 MJ/h input 300
- Appliances over 50 MJ/h input 500
b From the ground or above a balcony 300
c From a return wall or external corner 500
d From a gas meter (M) 1000
e From an electricity meter or fuse box (P) 500
f From a drain or soil pipe 150
g Horizontal from any building structure (unless appliance is approved
for closer installation) or obstruction facing a terminal 500
h From any other flue terminal, cowl or combustion air intake 500
j Horizontally from an openable window, door, or non-mechanical air inlet, or
any other opening into a building, with the exception of sub-floor ventilation
(see also Note (I)):
- Appliances up to 150 MJ/h input 500
- Appliances over 150 MJ/h input 1500
k Vertically below an openable window, door, or non-mechanical air inlet,
or any other opening into a building, with the exception of sub-floor ventilation
(see also Note (I)): see table below
Clearance 'k' in mm
Space Heaters All Other Appliances
Up to 50 MJ/h Up to 50 MJ/h input Over 50 MJ/h input Over 150 MJ/h input
input to 150 MJ/h input
150 500 1000 1500
NOTES:
(I) For mechanical air inlets, including spa blowers, the clearance 'j' and 'k' shall be 1500 mm in all cases.
(II) All distances shall be measured vertically or horizontally along the wall to a point in line with the nearest
par to of the terminal.
(III) Prohibited area below electricity meter or fuse box extends to ground level.
(IV)A flue terminal of this type shall not be located under a roofed area unless the roofed area is fully open on
at least two sides and a free flow of air at the appliance is achieved.

Masport FG39 FireGenie Freestanding Gas Stove 9
INSTALLATION
FLUEING ARRANGEMENTS
Vertical Terminations Using
Dura-Flue Fluing System for
Residential Manufactured and Mobile Homes
The shaded area in the diagram below shows all allowable
combinations of straight vertical and offset to vertical runs
with vertical terminations. Maximum two 45oelbows.
IftheflueisENCLOSEDinachase(min.size9"x9"/229mmx229mm)
maintain a 1-1/4" (38mm) clearance to combustibles.
May be installed in Manufactured (Mobile) Homes after first sale.
Horizontal Terminations for All Fluing Systems
The shaded areas in the diagram below show all allowable
combinations of vertical runs with horizontal terminations.
Maximum one 90Oelbow (two 45o elbows equal one 90oelbow).
LPG and NG:
Residential, Manufactured and Mobile Homes
Installations
The fluing arrangements diagrammed below, have a min. of 75% (flue
loss) efficiency with Fan Off, as required for manufactured homes.
(Actual efficiency may be as high as 85%)
May be installed in Manufactured (Mobile) Homes after first sale.
FlueRestrictorPosition
To set the Flue restriction as indicated in the diagram, simply loosen the
screws and push the flue restrictor plate to the correct position. Tighten
the screws.
Flue Restrictor setting at
40 Mj/h Flue Restrictor setting at
31 Mj/h

10 Masport FG39 FireGenie Freestanding Gas Stove
INSTALLATION
DV STOVE HORIZONTAL FLUE KIT (#946-112) INSTALLATION
MinimumInstallationHeight: FG39: 59-3/4" ( 1518mm)
Review the following sequence of instruc-
tions which are typical of most installations.
The sequence may vary depending on wall
thickness. Refer to flue location and clear-
ance dimensions on pages 8 to 9.
1) Set the unit in its desired location. Check
todetermine if wall studswill be inthe way
ofthefluingsystem,adjustlocationuntilall
clearances are met and there are no
obstructions.
Note: A 1-1/2"(38mm) clearance around
the outer pipe must be main-
tained except that only a 1"
(25mm) clearance is needed at
the termination end.
IMPORTANT:
Do not locate termination hood where
excessive snow or ice buildup may oc-
cur. Be sure to check flue termination
area after snow falls, and clear to pre-
vent accidental blockage of fluing sys-
tem. When using snow blowers, make
sure snow is not directed towards flue
termination area.
2) Assemble a trial fit to determine the ver-
tical center-line for the flue termination.
a) Cuta 241mmroundholeonboththe
interior and exterior wall.
b) Attach the 2 ft. (.6m) pipe section to
the flue terminal and slide into posi-
tion from the exterior. The larger
diameter end of the adjustable
pipe goes to the flue terminal.
c) Install the 90oelbow onto the adjust-
able pipe to determine the vertical
centerline of the starter collar on the
unit.
Note: if the centerline cannot be
met, the adjustable sections will
have to be cut.
DV STOVE HORIZONTAL FLUE KIT
Horizontal Stove Flue Kit (Part # 946-112) includes all the parts needed to install the FG39
Freestanding Gas unit with minimum horizontal and vertical vent dimensions. For installations that
require longer vertical and/or horizontal vents use the Dura-Vent system as shown in your manual.
Qty. Description
1) 2 Rigid Pipe Section 1.2m length, 165mm inside diameter
2) 1 Flex Liner, compressed aluminium 2 ply liner, 102mm inside diameter
3) 4 spring spacers
4) 1 90 deg. Elbow
5) 1 Decorative Wall Trim
6) 1 Adapter
7) 1AstroCap Termination Cap
8) 2 TrimCollar
9) 1 tube of Mill-Pac, high temperature sealant
10) 12 Screws, #8 x 1/2" (13mm) Self tapping, Stainless Steel
11) 14 Screws, #8 x 1/2" (13mm) Self tapping, Black
12) 4 Screws #8 x 1-1/2" (38mm)Drill Point, Stainless Steel
Optional:
946-206 Vinyl Siding Standoff for AstroCap
Note:
a) Liner sections should be continuous
without any joints or seams.
b) This is an approved system, therefore
components in this system must not be
substituted for any other manufactur-
er's products.
c) Wall Thimble is required when install-
ing through a combustible wall.

Masport FG39 FireGenie Freestanding Gas Stove 11
INSTALLATION
d) Cut the 2 ft. (.6m) section of rigid pipe
to length. Ensure that the pipe length
when cut will seat onto both the start-
er collar and the 90oelbow. Crimped
section of rigid pipe seats into
the 90oelbow. Only cut the un-
crimped side of pipe.
Dismantle all pipe sections including flue
terminal.
3) Attach the 4" (102mm) dia. flex liner to the
flue terminal ensuring that the flex overlaps
the collar of the flue terminal by a minimum
of 1-3/8"(35mm). Use Mill-Pac to seal and
secure with 3 of the #8 x 1/2" (13mm)
screws (stainless steel).
4) Attachthe 2 ft.(.6m) pipe sectionto theflue
terminalusingMill-Pac and/or high temper-
ature silicone and attach with 3 of the #8 x
1/2" (13mm) screws (stainless steel).
6) A bead of non-hardening mastic should be
run around both the termination and vinyl
siding standoff to prevent water from en-
tering and to make a tight seal between the
cap and the standoff.
7) Stretch the 4" (102mm) dia. flex liner out
fully and get a trial fit of the liner onto the 4"
dia. starter collar.
8) Cut the 4" (102mm) dia. flex liner to the
desired size.
Hint: leave an extra 12" (305mm) to 16"
(406mm) of length, this will make the final
assembly easier to work with.
9) Secure the 4" (102mm) dia. flex liner to the
4" adapter with Mill-Pac and 3 of the #8 x 1/
2" (13mm)screws (stainless steel).
10)Slide the Decorative Wall Cover over the
pipe sections.
11)Slide the 90oelbow (crimp end up) and the
2 ft. pipe section (crimp end up) over the
4" (102mm) dia. flex liner.
12) Slide the trim collar over the pipe section to
cover the joint.
13)Install the spring spacers onto the pipe
sections.
14)Secure the 4" (102mm) dia. flex liner with
adapter onto the stove collar. Put a bead of
Mill-Pac around the appliance adapter and
secure with 3 screws (#8 x 1/2" (13mm),
stainless steel).
15)Attach the pipe section onto the starter
collar by sealing with Mill-Pac and/or high
temperature silicone and securing with 3 of
the #8 x 1/2" (13mm) (black) screws. Pipe
seams should be facing the wall.
16)Attach the 90o elbow onto the pipe section
bysealingwithMill-Pacand/orhightemper-
ature silicone and securing with 3 of the #8
x 1/2" (13mm) screws (black).
17)Slide the 2 ft.(.6m)pipesectionontothe 90o
elbow. The flex may have to be com-
pressed back in order for the pipe to prop-
erly mate to the elbow. Seal with Mill-Pac
and/or high temperature silicone and se-
cure with 3 of the #8 x 1/2" (13mm) screws
(black). Pipe seams facing down.
18)Install the trim collar over the starter collar
and secure with a #8 x 1/2" (13mm)screw
(black).
If the pipe needs to be touched up, use only
Stove Brite High Temperature Metallic Black
Stove Paint.
NOTE: All inner joints must be sealed
with Mill-Pac.
All outer joints may be sealed with
high temperature silicone.
Note: The pipe seam should be facing
down.
Note: To make the instal-
lation more aes-
thetically pleasing,
we recommend
framing out a
square that the cap
can be mounted on.
Note: If installing termination on a siding
covered wall, a vinyl siding stand-
off or furring strips must be used
to ensure that the termination is
not recessed into the siding. For
vinyl siding standoff installation
refer to the Dura-Flue Termination
instructions.
5) Slide the partially connected pipe and flue
terminal assembly through the wall (from
theexteriorintothe interior) and secure the
cap to the exterior wall with 4 of the
supplied screws (#8 x 1-1/2" (38mm0 drill
point, stainless steel).
Note: The four screws provided for the
flue cap should be replaced with
appropriate fasteners for stucco,
brick, concrete, or other types of
sidings.
Hint: Apply the
sealant (Mill-
Pacand/orhigh
temperaturesil-
icone) to the
outer pipe be-
foreconnecting
the inner pipe.
#8 x ½" (13mm) Self Tapping, Stainless Steel
#8 x ½" Self Tapping, Black(13mm)
#8 x 1½" (38mm) Drill Point, Stainless Steel

12 Masport FG39 FireGenie Freestanding Gas Stove
Pipe Length
Round Support
Box/Wall Thimble
(Part # 940)
Round
Support Box/
Wall Thimble
(Part # 940)
Vertical
Terminal
Storm Collar
Part # 953
Flashing
943 or 943S
Ceiling Firestop
(Part # 963)
24" (610mm)
Pipe Length
Adj.Pipe Length
11" - 14-5/8"
(279mm - 372mm)
90 Elbow
o
Wall Thimble
Part # 942
Vinyl Siding
Standoff (Optional)
Part #950
AstroCap
Termination Cap
(Part# 946-523)
DURA-FLUE
TERMINATION KIT
Planning Your Dura-Flue
Installation
There are two basic types of Dura-Flue Room
Sealed System installations: horizontal termi-
nation and vertical termination. Confirm the
maximum horizontal run and maximum vertical
rise from the diagrams on page 9.
When planning your installation, it will be nec-
essary to select the proper length of flue pipe
for your particular requirements. For horizontal
installations,determinetheminimumclearance
from the rear of the unit to the wall. It is also
important to note the wall thickness. (The wall
thimble is suitable for 2' x 4' or 2' x 6' / .6m x 1m
or .6m x 2m wall construction.) Select the
amount of vertical rise desired for "vertical-to-
horizontal" type installations.
Warning: Always maintain required clear-
ances (air spaces) to nearby combusti-
bles to prevent a fire hazard. Do not fill air
spaces with insulation.
Theminimumclearancerequirementsbetween
the outer wall of the flue pipe and nearby
combustible surfaces is 1-1/4 inch. Be sure to
check the flue termination clearance require-
ments from decks, windows, soffits, gas reg-
ulators, air supply inlets and public walkways
as specified in the Exterior Flue Termination
Locations on page 8 and in your local building
codes.
Todeterminethelengthofflue piperequiredfor
verticalinstallations,measurethedistancefrom
the unit flue outlet to the ceiling, the ceiling
thickness, the vertical rise in an attic or second
storey, and allow for sufficient vertical height
above the roof line.
For multi-storey applications, fire stops are
required at each floor level. If an offset is
needed, additional pipe, elbows and supports
will be required.
Donotexceedthemaximumnumberofelbows.
One90ofor horizontal terminations andtwo 45o
for vertical termination.
DURA-FLUE FLUING
COMPONENTS
You will require the following components with
your new Masport Room Sealed Freestanding
GasStove.Pleasereviewyourproducttomake
sureyou haveeverythingyouneed. Intheeflue
that you are missing any part, contact your
dealer.
Note: These are the minimum pieces
required. Other parts may be re-
quired for your particular instal-
lation. See below for a list of flue
parts.
Ifinstallingterminationonasidingcoveredwall,
a vinyl siding standoff or furring strips can be
usedinordertoensurethattheterminationisnot
recessed into siding.
The vinyl siding standoff is required for walls
with vinyl siding.
Minimum components for a Dura-Flue
Horizontal Installation:
A) Dura-FlueHorizontal Termination Kit
B) Wall Thimble (required for combus-
tible walls)
Minimum components for a Dura-Flue
Vertical Termination:
C) Dura-Flue Vertical Termination Kit
The Simpson Dura-Flue Room Sealed System
offers a complete line of component parts for
installationofbothhorizontalandverticalinstal-
lation. Many items are offered in decorative
black, as well as galvanized finish. The galva-
nized pipe and fittings are used for concealed
INSTALLATION
locations such as attics or where corrosion is
afactor, such as above the roof line. Decorative
brass trim kits are available for both wall thim-
bles and ceiling support boxes.
Part # Description
971 Horiz.TerminationKitincludes:90o
black elbow, wall thimble cover,
horiz. square termination cap, 24"
blackpipe,11"-14"5/8"adjustable
black pipe
970 Basic Horiz. Termination Kit
includes: 90oblack elbow, wall
thimble cover, horiz. square
termination cap
978 Vert. Termination Kit includes
0/12 - 6/12 pitch adjustable
flashing, storm collar, low profile
term. cap
908B 6" (152mm) Pipe Length-Black
907B 9" (229mm) Pipe Length-Black
906 12" (304mm) Pipe Length Galv.
906B 12" (304mm) Pipe Length-Black
904 24" (610mm) Pipe Length Galv.
904B 24" (610mm) Pipe Length-Black
903 36" (914mm) Pipe Length Galv.
903B 36" (914mm) Pipe Length-Black
902 48" (1219mm) Pipe Length Galv.
902B 48" (1219mm) Pipe Length-Black
911B 11"-14 5/8" (219mm - 372mm)
Adj. Pipe Length-Black
917B 17"- 24" (432mm - 610mm)
Adj. Pipe Length Black
945 45O Elbow Galv.
945B 45OElbow-Black
945G 45O Elbow-Swivel Galv.
Dura-FlueBasic
Horizontal Kit # 970
190
oElbow
1 Wall Thimble Cover
1 Astro Cap

Masport FG39 FireGenie Freestanding Gas Stove 13
Diagram 5
Note: If installing termination on a siding cov-
ered wall, a vinyl siding standoff or furring
strips must be used to ensure that the
termination is not recessed into the siding.
The four wood screws provided should be
replaced with appropriate fasteners for
stucco, brick, concrete, or other types of
sidings.
5) Beforeconnecting the horizontal run of flue
pipe to the flue termination, slide the black
decorative wall thimble cover over the flue
pipe,thenslidetheWallThimble(Part#942)
over the flue pipe.
6) Slide the appliance and flue assembly to-
wards the wall carefully inserting the flue
pipe into the flue cap assembly. It is impor-
tant that the flue pipe extends into the flue
cap a sufficient distance so as to result in
a minimum pipe overlap of 1-1/4 inches
(32mm). Secure the connection between
the flue pipe and the flue cap using sheet
metal screws provided. See diagram 6.
FG39: 59-3/4" (1518mm)
Diagram 2
b) The location of the horizontal flue ter-
mination on an exterior wall must meet
all local and national building codes,
andmustnot be blocked orobstructed.
For External Flue Termination Loca-
tions, see diagram on page 8.
4) Ifinstallingtheflueterminationtoawallwith
vinyl siding, the Vinyl Siding Standoff must
be used. Attach the Vinyl Siding Standoff
to the Horizontal Flue Termination, but first
runabeadofnon-hardeningmasticaround
its outside edges, so as to make a seal
between flue cap and the standoff. Install
the Vinyl Siding Standoff (Part # 950) be-
tween the flue cap and the exterior wall
and attach with the four wood screws
provided. Seal around the Vinyl Siding
Standoff on all four sides. Diagram 5. The
arrow on the flue cap should be point-
ing up. Insure that the 1-1/4" (32mm)
clearances to combustible materials are
maintained. See diagram 5.
in diagram 2. Cut and frame the 10 inch
(254mm) square hole in the exterior wall
wherethefluewill be terminated. If the wall
being penetrated is constructed of non-
combustiblematerial,i.e.masonryblockor
concrete, a 7" (178mm) diameter hole is
acceptable.
Note:
a) The horizontal run of flue should have
a 1/4 inch (6mm) rise for every 1 foot
(.3m) of run towards the termination.
Never allow the flue to run downward.
This could cause high temperatures
and may present the possibility of a
fire.
INSTALLATION
DURA-FLUE
HORIZONTAL
INSTALLATIONS
1) Set the unit in its desired location. Check to
determine if wall studs or roof rafters are
in the way when the fluing system is
attached. If this is the case, you may want
to adjust the location of the unit.
2) RoomSealedpipeandfittingsaredesigned
with special twist-lock connections to con-
nect the fluing system to the appliance flue
outlet. A twist-lock appliance adaptor is
installed on the unit at the fac-
tory. Assemble the desired
combination of pipe and el-
bows to the appliance
adaptor with pipe
seams oriented to-
wards the wall or ceil-
ing, as much out of
view as possible. The
final positioning of the
pipeand90oelbowas-
sembly is deter-
mined by the
mounting orien-
tation of the
adaptor on the
stove and twist-
locked for a sol-
id connection.
Note:
a) Twist-lock procedure: Four indenta-
tions, located on the female ends of
pipes and fittings, are designed to slide
straight onto the male ends of adjacent
pipes and fittings, by orienting the four
Diagram 1
945BG 45OElbow-Swivel-Black
990 90O Elbow Galv.
990B 90OElbow-Black
990G 90O Elbow-Swivel Galv.
990BG 90OElbow-Swivel-Black
991 High Wind Term. Cap (Vertical)
980 Vertical Term. Cap
982 Snorkel-14" Rise Term.Cap
981 Snorkel-36" Rise Term.Cap
940 Wall Thimble-Support/Box
941 Cathedral/Ceiling-Support/Box
3951 BrassTrim-Wall Thimble/
CeilingSupport
963 Firestop Spacer
943 Flashing 0/12-6/12
943S Flashing 7/12-12/12
953 StormCollar
950 Vinyl Siding Standoff
988 Wall Strap
942 WallThimble
Parts not supplied by Dura-Flue
946-506/P Flue Guard (Optional)
948-128 Vinyl Siding Shield
Astro Cap (Australian)
pipe indentations so they match and
slideintothefourentryslotsonthemale
ends (diagram 1). Push the pipe sec-
tions completely together, then twist-
lock one section clockwise approxi-
mately one-quarter turn, until the two
sections are fully locked. The female
locking lugs will not be visible from the
outside on the Black Pipe or fittings.
They may be located by examining the
insideofthefemaleends.Applysealant
"Mill-Pac" to inner pipe and high temp
silicone sealant to outer pipe on every
twist-lock joint.
Hint: Apply silicone to female end.
b) Horizontalruns of flue must be support-
ed every three feet. Wall straps are
available for this purpose.
3) Withthepipeattachedtothestove,slidethe
stove into its correct location, and mark the
wall for a 10" x 10" (254mm x 254mm)
(inside dimensions) square hole. The cent-
erof the square holeshould line upwith the
centerline of the horizontal pipe, as shown

14 Masport FG39 FireGenie Freestanding Gas Stove
Diagram 11: The upper half of the flashing is
installed under the roofing material and not
nailed down until the chimney is installed.
This allows for small adjustments.
4) Assemblethedesired lengths of black pipe
and elbows necessary to reach from the
appliance adaptor up though the Round
Support Box. Insure that all pipes and
elbow connections are in the fully twist-
locked position and sealed.
5) Cut a hole in the roof centred on the small
drilledholeplaced in the roof in Step 2. The
holeshouldbe of sufficient size to meet the
minimum requirements for clearance to
combustibles of 1-1/4" (32mm). Slip the
flashingundertheshingles(shinglesshould
overlap half the flashing) as per diagram
11.
Diagram 12
7) Ensure flue is vertical and secure the base
of the flashing to the roof with roofing rails,
slide storm collar over the pipe section and
seal with a mastic.
8) Install the vertical termination cap by twist
locking it.
6) Continue to assemble pipe lengths.
Note: If an offset is necessary in the attic
to avoid obstructions, it is impor-
tant to support the flue pipe every
3 feet, to avoid excessive stress
on the elbows, and possible sep-
aration. Wall straps are available
for this purpose. See diagram 7.
Galvanized pipe and elbows may be uti-
lized in the attic as well as above the
roofline. The galvanized finish is desirable
above the roofline due to its higher corro-
sion resistance.
Continue to add pipe sections through the
flashing until the height of the flue cap
meets the minimum height requirements
specifiedindiagram12orlocalcodes. Note
that for steep roof pitches, the vertical
height must be increased. A poor draft, or
down drafting can result from high wind
conditions near big trees or adjoining roof
lines, in these cases, increasing the flue
height may solve the problem.
Roof Pitch Minimum Flue Height
Feet Meters
flat to 7/12 2 0.61
over 7/12 to 8/12 2 0.61
over 8/12 to 9/12 2 0.61
over 9/12 to 10/12 2.5 0.76
over 10/12 to 11/12 3.25 0.99
over 11/12 to 12/12 4 1.22
over 12/12 to 14/12 5 1.52
over 14/12 to 16/12 6 1.83
over 16/12 to 18/12 7 2.13
over 18/12 to 20/12 7.5 2.29
over 20/12 to 21/12 8 2.44
Diagram 10
Diagram 9
Diagram 8
Diagram 7
Diagram 6
DURA-FLUE VERTICAL
TERMINATION
1) Maintain the 1-1/4" (32mm)
clearances (air spaces) to
combustibles when pass-
ingthroughceilings,walls,roofs,
enclosures, attic rafter, or other
nearby combustible surfaces.
Do not pack air spaces with
insulation. Check page 9 for
the maximum vertical rise of
the fluing system and the max-
imumhorizontaloffsetlimitations.
3) ToinstalltheRoundSupportBox/WallThim-
bleinaflatceiling,cuta10inchsquarehole
in the ceiling centred on the hole drilled in
Step2.Frametheholeasshownindiagram
10.
INSTALLATION
7) InstalltheWallThimbleinthe centerofthe
10" square and attach with wood screws.
8) Slide the decorative wall thimble up to the
wall surface being careful not to scratch
the paint and attach with screws provid-
ed. Apply decorative brass or chrome trim
if desired. See diagram 7.
2) Set the gas appliance in its
desired location. Drop a
plumb bob down from the
ceiling to the position of
theapplianceflueexit,and
mark the location where
the flue will penetrate the
ceiling.Drillasmallholeat
his point. Next, drop a
plumbbobfromtheroofto
thehole previously drilled in
theceiling,andmarkthespot
where the flue will penetrate the roof.
Determine if ceiling joists, roof rafters or
other framing will obstruct the fluing sys-
tem. You may wish to relocate the appli-
ance or to offset, as shown in diagram 9 to
avoid cutting load bearing members.

Masport FG39 FireGenie Freestanding Gas Stove 15
INSTALLATION
OffsetChart
Diagram 13
Notes:
a) For multistorey vertical installations, a
CeilingFirestop(Part#963)isrequired
at the second floor, and any subse-
quent floor. Diagram 13. The opening
should be framed to 10 " x 10" inside
dimensions, in the same manner as
shown in diagram 10.
b) Any occupied areas above the first floor,
including closets and storage spaces,
through which the vertical flue passes,
must be enclosed.
Slope "X"
0/12 -2/12 4" (102mm)
2/12 -7/12 5-1/2" (140mm)
7/12 -12/12 6-3/4" (172mm)
12/12-24/12 7-1/2" (191mm)
24/12+ 12-1/2" (378mm)
CATHEDRAL CEILINGS
Round Support (RDS) &
Square Support (SQS)
If your home has a cathedral ceiling (no attic
space between the ceiling and the roof), install
the chimney and support as follows.
1) Situate the chimney in a convenient loca-
tion as near as possible to the appliance
outlet. Cut and frame a hole in the roof for
the support. The sides of this hole must be
vertical with 1 1/4" clearance.
2) Place the support in the opening. Lower it
to the correct height as determined by the
table and diagram below.
Using a level, make sure the support is
vertical. If the support extends above the
roof,cutitflushwith the top of the roof. Nail
the support to the frame opening using (8)
3"(76mm)spiralnailsor#8x1-1/2"(38mm)
screws.
Note: If you are using a 6" (152mm)
square support you may find it
difficult to screw it in place be-
cause it is fairly small inside.
Simpson Dura-Flue has provided angle
brackets with this support which can be
screwed to the outside of the support box
and nailed to surrounding framing as re-
quired. Use a minimum of four #8 x 1/2"
(13mm) screws per bracket. In some
cases these brackets may need to be
trimmed(e.g.: to fitunderaflashing). Place
the Finish Collar around the support and
fasten it to the ceiling using the screws
provided.
3) Use appropriate roof flashing. Place the
flashing under the upper shingles and on
topofthelowershinglesapproximately half
of the flashing should be under the shin-
gles.
4) AssemblethedesiredlengthsofBlackPipe
and Elbows necessary to reach from the
appliance adaptor up through the support
boxandflashingtoproperheightasperDia.
12, local codes or page 9. Ensure that all
pipeandelbowconnectionsareintheirfully
twist lock position.
5) Ensure flue is vertical and secure flashing
totheroof withroofingnails. Slidethestorm
collar over the pipe section and seal with a
mastic.
6) Twistlockthefluecapontothelastsection.
SupportExtensions-Round
(RDSE)orSquare (SQSE)
Steep pitched cathedral ceilings may require
the use of a support extension. This piece fits
down inside the support and can be adjusted
to increase the support's length by up to 22"
(559mm). The extension is attached to the
support using the eight metal screws provided.
Be sure there is at least a 2 inch overlap where
the extension joins the support.
1-1/4" (32mm) Min.
1-1/4" (32mm) Min.
1-1/4"
(32mm)
Min. 1-1/4" (32mm) Min.
nails
Ceiling Firestop

16 Masport FG39 FireGenie Freestanding Gas Stove
INSTALLATION
GAS CONNECTION
The gas line should be rigid pipe. Copper may
also be used if approved by AG 601.
Thegasconnectionatthevalveis1/2male.For
minimumandmaximumsupplypressureseethe
System Data Table.
GAS PIPE PRESSURE
TESTING
The appliance must be isolated from the gas
supply piping system by closing its individual
manual shut-off valve during any pressure
testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig. (3.45
kPa). Disconnect piping from valve at pres-
sures over 3.45 kPa (14" w.c.).
The manifold pressure is controlled by a regu-
lator built into the gas control, and should be
checked at the pressure test point.
Note: To properly check gas pressure,
both inlet and manifold pressures
should be checked using the valve
pressure ports on the valve.
1) Makesurethevalveisinthe"OFF"position.
2) Loosen the "IN" (# 3) and/or "OUT" (# 4)
pressure tap(s), turning counterclockwise
with a 1/8" (3mm) wide flat screwdriver.
3) Attach manometer to "IN" and/or "OUT"
pressure tap(s) using a 5/16" (8mm) ID
hose.
4) Seal and or check the pilot outlet (# 8)
5) The pressure check should be carried out
with the unit burning and the setting should
be within the limits specified on the safety
label.
6) When finished reading manometer, turn off
the gas valve, disconnect the hose and
tighten the screw (clockwise) with a 1/8"
(3mm) flat screwdriver. Screw should be
snug, but do not over tighten.
S.I.T. Valve Description
1) On-Off Solenoid Valve EV1
2) On-Off Solenoid Valve EV2
3) Inlet Pressure Test Point
4) Outlet Pressure Test Point
5) Connection for Pressure Regulator/Com-
bustion Chamber Compensation
6) Pressure Regulator for Minimum and Max-
imum Outlet Pressure
AERATION
ADJUSTMENT
The burner aeration is factory set but may need
adjusting due to either the local gas supply or
altitude.
FG39 with 40 mj.
FG39-NG Fully Open
FG39-LPG Fully Open
FG39 with 31 mj.
FG39-NG 6 mm Open
FG39-LPG 10 mm Open
Caution: Carbon will be produced if the air
shutter is closed too much.
Note: Any damage due to carboning re-
sulting from improperly setting the
aeration controls is NOT covered
under warranty.
Burner Inlet Orifice Sizes:
NG LPG
Burner #32 #50
2.95mm 1.78mm
Max. Input NG 40Mj/h
LPG 38Mj/h
Min. Input NG 20 Mj/h
LPG 19Mj/h
Supply Pressure
NG min. 1.13 kPa
LPG min.2.75kPa
Manifold Pressure
NG .94kPa
LPG 2.55kPa
Electrical: 240 V. 1.13A 60Hz.
Circulation: 2 speed fan, 125/75 CFM.
Log Set: Ceramic fiber, 7 per set.
System Data
FG39 Converted to 31mj.
Burner Inlet Orifice Sizes:
NG #37 2.65mm
LPG #52 1.6mm
Max. Input - NG/LPG
31Mj/h
Min. Input - NG/LPG
16Mj/h
Supply Pressure
NG min. 1.13 kPa
LPG min.2.75kPa
Manifold Pressure
NG .89kPa
LPG 2.55kPa
Electrical: 240 V. 1.13A 60Hz.
Circulation:Variablespeedfan,125/75CFM.
Log Set: Ceramic fiber, 7 per set.
System Data
FG39 with 40mj.
7) Gas Outlet Pressure Electric Modulator
8) PilotOutlet
9) Main Gas Outlet
10)Side Outlet

Masport FG39 FireGenie Freestanding Gas Stove 17
INSTALLATION
Conversion Kit for NG to LPG Model #736-969
THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION!!
Burner Orifice
Conversion Kit 736-969 Contains:
Qty. Part # Description
1 904-641 Burner Orifice #50
1 908-528 Red"LPG"label
2 908-255 Label "Converted to LPG"
1 918-335 Instruction Sheet
1 910-920 Pilot Orifice
1) Shut off the gas supply and unplug the
power cord.
2) Open the front door and carefully remove
the logs and lava rock.
3) Remove burner.
4) Remove burner orifice with a 1/2" wrench
and discard. Use a wrench to hold on to the
elbow behind the orifice.
5) Reinstall new burner orifice LPG stamped
#50 and tighten.
18)Stick the conversion label "This unit has
been converted to LPG" on the control box
cover.
19)Reverse steps 16, 15 & 12.
Jumper Location
Jumper
8) Remove the NG orifice and replace it with
the LPG orifice.
9) Install the pilot tube to the pilot assembly.
10)Placethepilotassemblyoverthepilotextru-
sion tube and secure it with 2 screws.
11)Adjust the burner areation setting to fully
open and install the burner.
12)Removethepedestalbackcoverbyremov-
ing the 4 Philips screws.
Pilot Tube
7) Lift the pilot assembly and remove the pilot
tube using an 11mm wrench.
6) Remove the 2 screws which hold the pilot.
Pilot
Orifice Pilot Assembly
Pilot
Extrusion
Tube
13)Stick the conversion label "This unit has
been converted to LPG" over top of the
serial number decal.
14)Replace the yellow "NG" label with the red
"LPG"label.
15)Carefully pull out the control box.
Note: The control box is held in place by
velcro.
16)Remove the control box cover by undoing
the 3 screws. Maneuver through antenna.
Control Box
Cover
Antenna
17)Remove the jumper using a plier.
20)Open the bottom door and remove the front
panel by undoing the 6 screws.

18 Masport FG39 FireGenie Freestanding Gas Stove
InstallerNotice:
Theseinstructionsmustbeleftwith
the appliance.
Minimum pressure: Remove one of the
cables connected to the electric modulator.
Keeping the nut (B) blocked, screw in the
screw (C) to increase the pressure and
screw it out to decrease it. Use a screw-
driver 6 x 1 blade.
NOTE: The outlet pressure must be set to
minimum0.74kPa.
After carrying out all adjustments, block
the setting screws with paint, taking care
not to obstruct the breather orifice of the
pressure.
Put back the modulator plastic cap.
WARNING: To ensure the correct opera-
tionofthemodulatoritisnecessarythatthe
plastic cap (A) is returned to its original
location.
23)At the end of all setting and adjustment
operations, check electrical insulation and
gas leaks.
24)Reverse step 20.
25)Check operation of fan and flame control.
26)Check for proper flame appearance and
glow on logs.
Cable
Electric
Modulator
22) Adjusting the Outlet Pressure
All the adjustments must be carried out
in the following order:
Removethemodulatorplasticcap(A) using
needle nose pliers.
Maximumpressure: TurntheunitONto its
highest input rating. Screw in the nut (B) to
increase the outlet pressure and screw it
out to decrease it. Use a 10 mm wrench.
NOTE: The outlet pressure must be set to
maximum2.65kPa.
21)Turn on the gas supply and plug in the
power cord.
C
BA
INSTALLATION

Masport FG39 FireGenie Freestanding Gas Stove 19
LOG SET
INSTALLATION
Read the instructions below carefully
and refer to the diagrams. If logs are
broken do not use the unit until they are
replaced. Broken logs can interfere with
the pilot operation.
The gas log kit contains the following:
a) 02-65 Rear Log
b) 02-56 Middle Left Log
c) 02-44 Front Left Log
d) 02-46 Left Top Log
e) 02-45 Front Right Log
f) 02-47 Center Log
g) 02-48 MiddleRightLog
h) Embers
i) Lava
Note: Install Optional Brick Panels prior
to installing logs.
Embers. Embers
The "02" refer numbers (i.e. 02-65) are
molded into the rear of each log.
1) Carefully remove the logs from the box and
unwrap them. The logs are fragile, handle
with care - do not force into position.
2) Sprinkle the embers on the left and right
sides of the firebox base.
INSTALLATION
CONVERSION TO LOWER BTU RATING
THIS CONVERSION MUST BE DONE BY AN AUTHORIZED
GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION
!!
NG Conversion Kit 730-920
Contains:
Qty. Part # Description
1 904-240 Burner Orifice #37 (NG)
1 918-034 Decal "Converted to 30,000 Btu"
1 918-033 Instruction Sheet
LPG Conversion Kit 730-922
Contains:
Qty. Part # Description
1 904-390 Burner Orifice #52 (LPG)
1 918-034 Decal "Converted to 30,000 Btu"
1 918-033 Instruction Sheet
Additional Piece (pkg. with unit:
1 Log Bracket Restrictor
1) Shut off the gas supply.
2) Open the front door. Carefully remove the
logs and lava rock.
3) Remove burner. See diagram below.
Burner Orifice
4) Unscrew the 2 Rear
Log Pins and move
to the front hole po-
sition.
5) Remove Rear Log
Bracketandslidethe
Log Bracket Re-
strictor between the
Position the Log Bracket Restrictor between
the Rear Log Bracket and the burner.
6) Remove burner orifice with a 1/2" spanner
and discard.
7) Reinstall new burner orifice (NG stamped
#37 or LPG stamped #52) and tighten.
8) Reverse steps 3) and 2).
9) AdjustFluerestrictorsetting:TosettheFlue
restriction as indicated in the diagram, sim-
ply loosen the screws and push the flue
restrictorplate to the correct position.Tight-
en the screws.
Unit Btu/h Restrictor Opening
FG3940 Mj/h A 45mm
31Mj/h B 35mm
Note: Use a
magnetic type
screwdriver if
possible.
Rear Log Bracket and the burner, secure
with the 2 screws.
Flue Restrictor
setting at High Btu/h Flue Restrictor setting at Low Btu/h
10)Attach the label "This unit has been con-
verted to..." on top of the data badge over
the higher Btu information.
11)Check for gas leaks.
12)Check inlet and outlet pressures.
13)Check operationofflamecontrol. Checkfor
proper flame appearance and glow on logs.

20 Masport FG39 FireGenie Freestanding Gas Stove
Notch
E)02-45
Bracket
A)02-65
The bottom right edge of Log G)02-48 must
sit snugly against the bracket
Side View
G)02-48
E)02-45
F)02-47
11)Position notch in Front Right Log G)02-48
on Log F)02-47 and push the bottom right
edge against the bracket on the burner
tray.
G)02-48
12)Test fire to ensure proper light off (make
sure flame flows smoothly from one end of
burner to the other. If there is any flame
hesitation, check that area for any block-
age of the burner port.
F)02-47
E)02-45
A)02-65
G)02-48
D)02-46
B)02-56
C)02-44
Cutout
Pin
D)02-46
B)02-56
A)02-65
7) Place the Left Top Log D)02-46 on the pin
on Log B)02-56 and on top of the cutout on
Log A)02-65.
E)02-45
C)02-44
8) Place Front Right Log E)02-45 on the two
pins as shown.
9) Place thelavarockintheareabetweenthe
left and right logs, leaving a space in the
middle for log (F) 02-47.
CutoutNotch
F)02-47
E)02-45
A)02-65
10)Place thenotch inCenter LogF)02-47 over
Log E)02-45 and across the cutout on Log
A)02-65.
C)02-44
Pins on Rear Log Support
A)02-65
B)02-56
3) Place Rear Log A)02-65 on the two pins on
the rear log support.
4) Place the Middle Left Log B)02-56 on the
two pins as shown.
5) Sprinkle some lava rock just in front of B)
02-56 on the burner holes.
lava rock
B)02-56
6) Place Front Left Log C)02-44 onto the 2
front pins as shown.
INSTALLATION