Charnwood Island Product guide

Operating & Installation Instructions
charnwood
I
I S L A N D
IIIII
®
Version AZ, BZ, CZ

C O N T E N T S
O P E R AT I N G I N S T R U C T I O N S
Fuel 2
Door Operation 2
Multi Grate 2
Refuelling 5
Maintenance 5
Throat Plate & Flueway Cleaning 5
Chimney Sweeping 6
Trouble Shooting 6
If you need Further help 7
INSTALLATION INSTRUCTIONS
Health & Safety Precautions 8
Specification 8
Chimney 8
Hearth & Fire Surround 9
Island I Dimensions 11
Riddling 3
Controlling The Fire 3
Ash Clearance 3
Lighting 4
CO Alarms 8
Connection to Flues 9
Soot Doors 10
Pre Lighting Check 10
Commissioning 10
Island II Dimensions 12
Parts Lists 14 - 16
Certification 17
Island III Dimensions 13
I
I S L A N D
IIIII
Ref. Island I.II.III z 06.14 Rev. 1

Logs of the following sizes are suitable:
This appliance has been approved by HETAS as an intermittent
operating appliance for burning dry seasoned wood logs only.
HETAS approval does not cover the use of other fuels either alone
or mixed with wood logs nor does it cover the instructions for the
use of other fuels.
DOOR OPERATION
The door handle has been carefully designed so that in normal use it
may be operated using bare hands. However, if you need to open
the doors when the fire is running at maximum then the use of a
cloth or glove may be required.
Take care not to touch the doors as they will be hot when the fire is
burning. Turn the door handle clockwise to open, and anti-clockwise
to close. The stove is normally run with the doors shut.
Before lighting the stove check with the installer that the work and
checks described in the Installation Instructions have been carried
out correctly and that the chimney has been swept, is sound and free
from any obstructions. The stove is not suitable for use in a shared
flue system.
When using the stove in situations where children, aged and/or
infirm persons are present a fireguard must be used to prevent
accidental contact with the stove. The fireguard should be
manufactured in accordance with BS 8423:2002.
Do not use an aerosol spray on or near the stove when it is alight as
there is a serious risk of explosion or flash ignition of the spray.
FUEL
This stove is intended primarily for burning wood. Only dry, well
seasoned wood should be burnt on this appliance as burning wet
unseasoned wood will give rise to heavy tar deposits in the stove, on
the glass and within the chimney. For the same reason hard woods
(such as Ash, Beech and Oak) are better than soft woods (such as
Pine and Spruce). Burning wet unseasoned wood will also result in
considerably reduced outputs. The wood should be cut and split and
then left to season in a well ventilated dry place for at least one year
but preferably two years before use.
PETROLEUM COKE IS NOT SUITABLE FOR USE ON THIS
APPLIANCE. ITS USE WILL INVALIDATE THE GUARANTEE.
This stove is not designed to burn household waste. For advice on
other fuels please contact Charnwood.
Your Island stove has been designed to work with the minimum
effort. If any operation - such as riddling the grate or opening and
closing the doors - begins to require extra force then the cause must
be investigated and corrected to prevent damage being caused to the
stove.
If you are using your stove to burn wood logs in a smoke controlled
area, then the Smoke Reducing Kit MUST be fitted and the
instructions on lighting and refuelling MUST be followed.
Remember that the stove will be hot and that it is made from hard
materials. Ensure that you have a good balance before operating the
fire.
This stove is capable of intermittent operation.
This stove
will not produce significant smoke if well seasoned logs of less than
20% moisture content are burnt and these instructions are adhered
to. Burning wet (>20% moisture content) wood and operating the
stove in an irresponsible manner may produce smoke which is illegal
in smoke controlled areas.
Fig. 1. Stove Controls
OPERATING INSTRUCTIONS
®
charnwood
2
I
I S L A N D
IIIII
Maximum Length
Approx. Diameter
Island 1
370mm (14.5")
Up to 100m (4")
Island 2
440mm (17.25")
Up to 100 mm (4")
Island 3
550mm (21.6")
Up to 100mm (4")
Front to Back Loading
(all models)
240mm (9.4")
Up to 100mm (4")
Air Control
Pull to Open
Grate Lever
Identification Plate
Lift to view
Riddling & Ashpan
Tool in Holder

MULTI GRATE
Your Charnwood Island is fitted with a multi grate to enable wood to
be burned and ash to be cleared. The grate has two positions:
1) In the open position the grate bars are vertical with gaps in
between allowing the primary combustion air to come up through
the grate and through the fuel bed.
2) In the closed position the grate bars are horizontal, allowing the
combustion air to come round the sides of the grate and over the
top of it. When in the closed position ash is able to build up on the
grate as is necessary for effective wood burning.
Movement of the grate from one position to the other is effected
using the tool supplied as shown in Fig. 2. The grate is put into the
open position by moving the tool up until the handle is in the 1
o'clock position. The grate is put into the closed position by moving
the tool down until the handle is in the 5 o'clock position. To riddle
the appliance, the tool should be moved between the open and
horizontal positions several times. When burning wood the ash
should be allowed to build up and riddling should only be carried out
once or twice a week.
RIDDLING
When burning wood, ash should be allowed to build up and only
riddled when the ash begins to cover the slots in the rear fireplate.
The fire should be riddled with the doors shut (see Fig. 2). Place the
tool onto the riddling lever and rotate between the 1 o'clock and 3
o'clock positions several times. Too much riddling can result in
emptying unburnt fuel into the ashpan and should therefore be
avoided. After riddling, the grate should be put back into the open
or closed position as required (the tool should be in the 1 o'clock
position for open grate or in the 5 o'clock position for closed grate).
*Patent No.2389414
Fig. 2. Multifuel Grate
OPERATING INSTRUCTIONS
®
charnwood
I
I S L A N D
IIIII
CONTROLLING THE FIRE
The fire is controlled by the single air control knob shown in Fig. 3.
Pull the knob out to make the fire burn faster, push it in to make the
fire burn slower.
TM
This unique QuattroFlow air control* provides carefully balanced
primary, secondary, tertiary and bypass air to enable optimum
burning conditions without the need to fiddle with multiple controls.
For correct firing we recommend the use of a stove pipe
thermometer which may be purchased from your supplier or from
ourselves.
ASH CLEARANCE
The ashpan should be emptied regularly before it becomes too full.
Never allow the ash to accumulate in the ashpan so that it comes in
contact with the underside of the grate as this will seriously damage
the grate bars. The ashpan is handled using the tool and gloves
provided. Care should be taken to ensure that ash is cool before
emptying it into plastic liners or bins.
To make ash removal easier there is a special Charnwood ash carrier
available. This may be purchased from your supplier or, in case of
difficulty, from ourselves.
TOOL HOLDER
The tool holder is fitted by the installer underneath the front facing
left leg and is supplied inside a bag. To fit the tool holder, slacken the
bolt (located under front facing left leg) with a 13mm spanner, slide
the tool holder in to place and tighten the bolt back up again. Once
fitted, the tool holder will hold the riddling/ashpan tool when it is
not in use.
Fig. 3 Air control
Position of air control
handle on stove 12 3 4
1. Slumber
2. Medium output
3. High output
4. Boost
Air control handle
Riddle
Closed Position
Open Position
3

Once long flames appear over the fire, reduce the air control to the
“high output” setting. Once the fire is well established - with each
log alight at the top - the air setting can be reduced again, depending
on the type of fire required.
Once the fire is up to temperature the airwash system will begin to
work, so allow the fire to become hot before adjusting the air
controls to the required setting. If at any stage the flames start to go
out or the glass begins to discolour, a higher setting is required. To
achieve this, pull the air control back out to re-establish a consistent
burn.
During the lighting period, do not leave the stove unattended. Do
not leave the door open except as directed above to avoid excessive
smoke. When relighting the stove, riddle slightly and then empty the
ashpan.
LIGHTING
On initial lighting, the stove may smoke and give off an odour as the
silicon paint with which the firebox is painted reacts to the heat. This
is normal and will cease after a short time, but meanwhile the room
should be kept well ventilated. At first only light a small fire and burn
it slowly for two hours to allow any residual moisture in the bricks to
evaporate.
Light the stove using dry kindling wood and paper or fire lighters.
Set the grate into the closed position. Place the paper, or fire
lighters, and kindling on the grate and cover with a few small dry
logs. Open the air control fully (see Fig. 3). Light the paper or fire
lighters. The door may be left cracked open for a few minutes to
assist the combustion and heat up the firebox more quickly.
When the kindling wood is well alight add a few small logs and close
the door, but leave the air control fully open. When the flames are
established around the smaller logs, load the stove with larger logs
to the level of the air holes in the back firebricks. See page 4 for
maximum log sizes for each stove. Maintain the air control at
maximum at this stage.
OPERATING INSTRUCTIONS
®
charnwood
I
I S L A N D
IIIII
Fig. 5 Building up the fire
Fig. 6 Adding larger logs
Fig. 7 Fire well underway
Fig. 4 Initial Firing
4

OPERATING INSTRUCTIONS
®
charnwood
I
I S L A N D
IIIII
Fig. 8. Throat Plate
REFUELLING
Keep the firebox filled up to the level of the air holes in the back
firebrick, but do not overfill to prevent fuel from spilling over the top
of the front fire bar. Logs should be evenly distributed, filling the
firebed to give the most pleasing flame pattern. The air control must
be fully opened after refuelling until the flames are established above
the fire. It is best to refuel on to a hot bed of ash. If at this point the
fire starts to die, the doors must be cracked open until the fire is
revived in order that smoke may not be produced. If the fire has
started to die down before refuelling, then more kindling wood must
be added, the air control opened fully and the door cracked open to
re-establish the firebed before adding larger logs.
Care should be taken especially when burning wood that fuel does
not project over the front fire bar or damage to the glass may be
caused when the doors are closed. It can also cause the glass to
blacken. Maximum filling height is such that logs cannot fall from the
fire when the doors are opened. Liquid fuels are not to be used on
this appliance.
MAINTENANCE
Cleaning
The stove is finished with a high temperature paint which will
withstand the temperatures encountered in normal use. This may be
cleaned with a damp lint-free cloth when the stove is cold. Should re-
painting become necessary then special high temperature paints are
available from your supplier or from Charnwood.
Cleaning the Glass
The glass in the doors is a special ceramic glass which is able to
withstand high temperatures. Before cleaning the glass open the
doors and allow them to cool. Clean the glass using a damp cloth and
then wipe over with a dry cloth. Any stubborn deposits on the glass
may be removed with a proprietary stove glass cleaner or ceramic
hob cleaner. Some deposits on the glass may be burnt off simply by
running the fire at a fast rate for a few minutes. Do not use abrasive
cleaners or pads as these can scratch the surface which will weaken
the glass and cause premature failure. Aerosol spray cleaners should
not be used near the appliance whilst it is under fire.
When Not in Use
If the fire is going to be out of use for a long period (for instance in
the summer) then to prevent condensation, and hence corrosion,
the air control should be left fully open and the fire doors left ajar. It
is also advisable to sweep the chimney and clean out the fire.
Spraying the inside of the doors and firebox with a light oil, such as
WD40, will also help to keep all internal parts working well.
After long periods where the fire has been out of use, the chimney
and appliance flueways should be cleaned before lighting.
Door Seals
For the fire to operate correctly it is important that the door seals
are in good condition. Check that they do not become worn or
frayed and replace them when necessary.
Servicing
It is recommended that the fire is serviced once a year to keep it in
first class working order. After cleaning out the firebox thoroughly,
check that all internal parts are in good working order, replacing any
parts that are beginning to show signs of wear. Check that the doors
seals are in good condition and that the doors seal correctly. A
servicing guide is available on request. Repairs or modifications may
only be carried out by the Manufacturer or their approved agents.
Use only genuine Charnwood replacement parts.
THROAT PLATE AND
FLUEWAY CLEANING
It is important that the throat plate and all the stove flueways are
kept clean. They should be checked approximately once a week, by
looking up into the firebox for signs of soot or fly-ash on the throat
plate and at the sides of the firebox. If there are signs of a build up of
soot or fly-ash deposits then the fire must be let out in order to
clean the throat plate and flueways.
Before attempting to clean the throat plate and flueways, ensure that
the fire is cold. Wear suitable gloves to prevent irritation from soot
deposits. To remove the throat plate lift the front edge up and slide
the plate forward until it comes clear of the front pegs, then swing
the front edge down (see Fig. 8).
Lift throat plate at
front, then pull forward
and swing down.
5

OPERATING INSTRUCTIONS
®
charnwood
I
I S L A N D
IIIII
CHIMNEY SWEEPING
The chimney should be swept at least once a year. Where a top
outlet is used it will generally be possible to sweep the chimney
through the appliance.
First remove the front firebar, side fire plates, and the throat plate.
Then sweep the chimney ensuring that soot is removed from all
horizontal surfaces after sweeping.
In situations where it is not possible to sweep through the appliance
the installer will have provided alternative means, such as a soot
door.
After sweeping the chimney the appliance flue outlet and the flue
pipe connecting the stove to the chimney must be cleaned with a flue
brush.
After clearing any soot from within the stove, replace the throat
plate (see Fig. 8), the side fireplates, and front firebar.
Different types of sweep’s brushes are available to suit different
flueways. For prefabricated insulated chimneys the manufacturers
instructions with regard to sweeping should be consulted.
TROUBLE SHOOTING
Fire Will Not Burn
Check that:
a) the air inlet at the rear of the stove is not obstructed in any way,
b) chimneys and flueways are clear,
c) a suitable fuel is being used,
d) there is an adequate air supply into the room,
e) an extractor fan is not fitted in the same room as the stove,
f) there is sufficient draw in the chimney, (once the chimney is warm
a draught reading of at least 0.05 inches (1.25mm) water gauge (12
Pa) should be obtained).
Blackening of Door Glass
Keeping the glass clean requires a certain amount of
experimentation due to the differences in the draw of different
chimneys. The following points should be noted and with a little care
should enable the glass to be kept clean in most situations:
a) The airwash relies on a supply of heated air to keep the glass
clean. Therefore, when lighting the stove, allow the firebed to
become well established before closing the air control. This also
applies when re-fuelling the stove.
b) When re-fuelling, keep the fuel as far back from the front firebar
as possible, do not try to fit too much fuel into the firebox.
c) Wet wood or logs overhanging the front firebars will cause the
glass to blacken.
d) There is a bypass slide that can be adjusted to suit the particular
installation. This allows a small amount of airwash air to enter the
stove even when the air control is closed. This can be adjusted to
help with keeping the glass clean when the fire is slumbering.
It is always more difficult to keep the glass clean when running the
stove very slowly for long periods.
Check that all flue connections and the blanking plate are well sealed.
It is also important that the chimney draw is sufficient (when the
chimney is warm a draught reading of at least 0.05 inches water
gauge (12 Pa) should be obtained), and that it is not affected by
down-draught.
Occasionally some blackening of the glass may occur below the level
of the front firebars. This will not obscure the view of the fire or
affect its performance.
Fume Emission
Warning Note: Properly installed and operated this appliance
will not emit fumes. Occasional fume from de-ashing and re-
fuelling may occur. Persistent fume emission is potentially
dangerous and must not be tolerated. If fume emission does
persist, then the following immediate actions should be taken:
a) Open doors and windows to ventilate the room, and then
leave then premises.
b) Let the fire go out.
c) Check for flue or chimney blockage, and clean if required.
d) Do not attempt to re-light the fire until cause of fume has been
identified, if necessary seek professional advice.
The most common cause of fume emission is flueway or chimney
blockage. For your own safety these must be kept clean.
CO Alarm
Your installer should have fitted a CO alarm in the same room as the
appliance. If the alarm sounds unexpectedly, follow the instructions
given under “Warning Note” above.
Fire blazing out of control
Check that:
a) The doors are tightly closed.
b) The air control is pushed in.
c) A suitable fuel is being used.
d) Door seals and air control flap pads are intact.
Chimney Fires
If the chimney is thoroughly and regularly swept, chimney fires
6

OPERATING INSTRUCTIONS
®
charnwood
I
I S L A N D
IIIII
should not occur. However, if a chimney fire does occur push the air
control in fully tightly close the doors of the appliance. This should
cause the chimney fire to go out in which case the control should be
kept closed until the stove has gone out. The chimney and flueways
should then be cleaned. If the chimney fire does not go out when the
above action is taken then the fire brigade should be called
immediately.
After a chimney fire the chimney should be carefully examined for
any damage. Expert advice should be sought if necessary.
IF YOU NEED FURTHER HELP
If you need further help with your Charnwood Island then your
Installer will be able to provide the answers to most questions. Your
Local Charnwood Premier Dealer has a great deal of experience and
will also be able to provide helpful advice. Further help is available
from the Charnwood Customer Services department who will be
pleased to give advice, if necessary.
7

INSTALLATION INSTRUCTIONS
®
charnwood
I
I S L A N D
IIIII
HEALTH AND SAFETY PRECAUTIONS
Please take care when installing the stove that the requirements of
the Health and Safety at Work Act 1974 are met.
Some types of fire cement are caustic and should not be allowed to
come into contact with the skin. In case of contact wash with plenty
of water. If there is a possibility of disturbing any asbestos in the
course of installation then please use appropriate protective
equipment.
There must not be an extractor fan fitted in the same room as the
stove as this can cause the appliance to emit fumes into the room.
This stove is not suitable for use in a shared flue system.
In addition to these instructions the requirements of BS.8303 and
BS EN15287-1:2007 must be fulfilled. Local Authority Bylaws and
Building Regulations, including those referring to National and
European Standards regarding the installation of Solid Fuel burning
appliances, flues and chimneys must also be observed.
There must be an adequate air supply into the room in which the
appliance is installed to provide combustion air. The has
5kW output and therefore a permanent air vent is not normally
required. The combustion air supply for Island 2 & 3 must be via a
2
permanently open vent. Minimum free areas are: : 16.5cm
2 2 2
(2.5 in ) & : 38.5cm (6 in ).
Island 1
Island 2
Island 3 This is particularly necessary if
the room is double glazed. It must be positioned such that it is not
liable to blockage.
CO ALARMS
Building regulations require that when ever a new or replacement
fixed solid fuel or wood/biomass appliance is installed in a dwelling a
carbon monoxide alarm must be fitted in the same room as the
appliance. Further guidance on the installation of the carbon
monoxide alarm is available in BS EN 50292:2002 and from the
alarm manufacturer's instructions. Provision of an alarm must not be
considered a substitute for either installing the appliance correctly or
ensuring regular servicing and maintenance of the appliance and
chimney system.
CHIMNEY
In order for the appliance to perform satisfactorily the chimney
height must not be less than 4 metres measured vertically from the
outlet of the stove to the top of the chimney. For the Island 1 &
Island 2 the chimney must not be less than 150mm (6 inches)
internal diameter or 150 x 150mm internal square. For the Island 3
the chimney must not be less than 175mm (7 inches) internal
diameter or 175 x 175mm internal square. If an existing chimney is
to be used, it must be swept and checked, it must be in good
condition, free from cracks and blockages, and should not have an
excessive cross sectional area. If you find that the chimney is in poor
condition then expert advice should be sought regarding the
necessity of having the chimney lined. If it is found necessary to line
the chimney then a lining suitable for Solid Fuel must be used.
If there is no existing chimney then a prefabricated block chimney or
a twin walled insulated stainless steel flue to BS EN15287-1:2007
can be used either internally or externally. These chimneys must be
fitted in accordance with the manufacturers instructions and Building
Regulations.
Anki pumice liners or chimney blocks will give a highly insulated
chimney which will work well with all fuels. For details ring Anki
Chimney Systems on [phone].
Single wall flue pipe, of diameter no less than the stove outlet, is
suitable for connecting the stove to the chimney but is not suitable
for using for the complete chimney.
If it is found that there is excessive draw in the chimney then a
draught stabilizer should be fitted.
It is important that there is sufficient draw in the chimney and that
the chimney does not suffer from down-draught. When the chimney
is warm the draw should be not less than 0.05 inches water gauge
(12Pa). If in doubt about the chimney seek expert advice.
Specification
Island I
Island II
Island III
Output kW
5.0
8.0
12.0
(BTU/h)
(17,061)
(27,300)
(40,946)
Mass kg
130
140
170
Flue Gas Temp °C
254
290
365
Flue Gas Mass Flow g/s
4.8
5.9
8.1
Max Hearth Temp °C
61.5
78.8
93.7
SPECIFICATION
8

Register Plate
With Soot Door
Alternative
Soot Door Positions
Fig. 11 Horizontal Register Plate With Top Flue Connection
Register Plate
With Soot Door
Alternative
Soot Door Positions
Fig. 10 Horizontal Register Plate With Rear Flue Connection
Register Plate
Soot Door
In Side or Rear
Of Chimney
Fig. 9 Vertical Register Plate With Bricked Up Fireplace
INSTALLATION INSTRUCTIONS
®
charnwood
I
I S L A N D
IIIII
HEARTH AND FIRE SURROUND
The stove arrives bolted and shrink-wrapped to its pallet which is
intended to be cut up and used for kindling fuel.
The stove must stand on a fireproof hearth and combustible
materials must not be used in the construction of the fireplace unless
adequately fireproofed in accordance with local building regulations.
The hearth must be at least 12mm (0.5inches) thick. The positioning
of the stove and the size of the hearth are governed by building
regulations for Class 1 appliances. These building regulations state
that the hearth must extend in front of the stove by at least 225mm
(9 inches) and to the sides of the stove by at least 150mm (6
inches).Where possible it is helpful for the hearth to extend as far as
the doors when fully opened. If in doubt as to the positioning of the
stove expert advice should be sought either from the supplier or the
local building inspector.
The fireplace must allow good circulation of air around the appliance
to ensure that maximum heat is transferred to the room and also to
prevent the fireplace from overheating. A gap of 150mm (6 inches)
each side and 300mm (12 inches) above the appliance should give
sufficient air circulation. If a wooden mantelpiece or beam is used in
the fireplace it should be a minimum of 460mm (18 inches), and
preferably 600mm (24 inches) from the appliance. In some situations
it may be necessary to shield the beam or mantelpiece to protect it.
In order for the fire to operate correctly there must be an air gap
behind the appliance of at least 40mm, but be aware that this
distance will need to be greater in some cases to meet Building
Regulation requirements.
CONNECTIONS TO FLUES
There are several ways of connecting the stove to the flue. These are
illustrated in figures 9 to 12.
If a top flue connection (as shown in Fig. 11) or the vertical rear flue
connector (shown in Fig. 12) are used, then the chimney may be
swept through the appliance.
Horizontal lengths of flue must be kept to a minimum and should
not be more than the flue diameter. The sealing face of the flue
collar should be coated with fire cement before fixing to the body of
the stove using the two screws provided. The blanking plate must be
removed, sealed with fire cement and refitted, care being taken to
ensure that the fold on the clamping plate is in line with the lugs on
the firebox as shown on the label on the clamping plate. Ensure that
the clamping plate does not prevent the throat plate from seating
correctly. All flue connections must be well sealed.
9

Register Plate
With Soot Door
Alternative
Soot Door Positions
Fig. 12 Horizontal Register Plate With Optional
Vertical Rear Flue Connector
158mm Island 1 & 2
197mm Island 3
INSTALLATION INSTRUCTIONS
®
charnwood
I
I S L A N D
IIIII
SOOT DOORS
It is possible to pass a 16 inch diameter sweeps brush through the
appliance but in most back outlet installations it will be necessary to
have a soot door to enable the chimney to be swept. This may either
be in the actual brickwork of the chimney or in the register plate.
Various types and positions of soot doors are shown in figs. 9 to 12.
PRE LIGHTING CHECK
Before initial lighting the following points should be checked:
1. The bottom grate bars must all be fitted and should move freely and
easily when the ridding mechanism is operated.
2. The plates round the sides and back of the grate must be in position
and sitting correctly.
3 The throat plate must be fitted in the roof of the appliance and should
be checked to ensure that it has not become dislodged in transit. The
method of location and positioning of the throat plate is shown in Fig. 8.
COMMISSIONING
On completion of the installation and after allowing a suitable period
of time for the fire cement and mortar to dry out, the stove should
be lit and checked to ensure that smoke and fumes are taken from
the appliance up the chimney and emitted safely. Also check all joints
and seals. On completion of the installation and commissioning
please leave the operating instructions with the customer and advise
them on the use of the appliance.
10

I
I S L A N D
charnwood
HIGH LEG STORE STAND STANDARD LEG
FRONT VIEW SIDE VIEW BACK VIEW
TOP VIEW
533
670
551
331
Max dim. with door open = 601
Optional Vertical Rear Flue Adapter
88
410
132
163
465
143
634
565
579
99
355
439
155
Optional External Air Manifold
464
87
565
726
379
439
190 178
555
514
760
565
705
299
225 213
420
100
590
Flue outlet to suit 150mm (6") flue pipe
ISLAND I DIMENSIONS (mm)
®
charnwood
I
I S L A N D
IIIII
11

I I
I S L A N D
charnwood
®
HIGH LEG STORE STAND STANDARD LEG
FRONT VIEW SIDE VIEW BACK VIEW
TOP VIEW
605
622
331
Max dim. with door open = 639
Optional Vertical Rear Flue Adapter
132
421
160
476
88
143
674
634
619
99
155
365
447
Optional External
Air Manifold
87
504
765
634
710
875
634
820
584
447
190
393
48
179
595
301
295 289
451
120
705
Flue outlet to suit 150mm (6") flue pipe
ISLAND II DIMENSIONS (mm)
®
charnwood
I
I S L A N D
IIIII
12

III
I S L A N D
charnwood
I I
I S L A N D
charnwood
FRONT VIEW SIDE VIEW BACK VIEW
HIGH LEG STORE STAND STANDARD LEG
TOP VIEW
Max dim. with doors open =705
Optional Vertical Rear Flue Adapter
105
452 533
171 147
186
713
765
763
732
108
845
765
795
750
945
995
714
484
196
400
484
428
190
400
48
335
309
Optional External
air manifold
588
107
670
189
820
339
Flue outlet to suit 175mm (7") flue pipe
ISLAND III DIMENSIONS (mm)
®
charnwood
I
I S L A N D
IIIII
Note: Dimensional drawings have been
fudged to show curved tops with correct dimensions
13

Issue B
* These items are not shown on the drawing.
# Please specify colour when ordering.
To obtain spare parts please contact your local stockist giving Model, Part Number
and Description. In case of difficulty contact the manufacturer at the address
shown.
This drawing is for identification purposes only.
®
charnwood
T: +4 4 ( 0) 19 83 5377 99 • F:+ 44 (0 )1983 537788 • SPAR ES @CH ARNWOOD .CO M • WWW.C HA RNWOO D.C OM
BISHOPS WAY, NEWPORT, ISLE OF WIGHT PO30 5WS, UNITED KINGDOM
ISLAND I (az) PARTS LIST
®
charnwood
I
I S L A N D
IIIII
Item Part Number Description
1* 008/AY62S Door Seal Set Inc. Adhesive 32 008/PX95 Riddling/Ashpan Tool
2* 008/FW29 Door Seal Adhesive 33 004/BX048 Tool Holder
3 002/CG20 Bottom Grate Bar 34 002/PX89 Riddler Knob
4 002/CG20S10 Set of Grate Bars (10) 35 004/AY21 Air Bypass Slide
5 002/CY15 Side Fire Plate 36 004/AY22-1P Primary Air Inlet Flap
6 002/AY16 Back Fire Plate 37 004/AY22-1S Secondary/Bypass Air Inlet Flap
7 004/BY24 Ash Shedding Plate 38 004/AY24-02 Flap Mounting Rod (Inc. Fixings)
8 006/AY18 Glass 39 004/BY23-07 Air Control Rod
9* 008/AY45 Glass Seal 40 004/AY23 Actuator Assembly
10 004/KV23 Glass Retainer 41 008/AY39 Upper Quattro Box Gasket
11 011/AY48S Set of Fire Bricks (4) 42 010/AY20 Upper Quattro Box
12 004/XV30 Brick Retainer (4) 43 010/AY19 Lower Quattro Box
13 010/AY47 Throat Plate 44# 002/AY01/A LH Door Assembly
14 008/AY26S Set of Air Inlet Flap Pads 45# 002/AY02/A RH Door Assembly
15 012/AY33 Mover Bar 46# 001/AZ010 Firebox (Island I az)
16 002/AY30 Carrier Bar 47# 012/TW09 Blanking Plate
17 012/AY13 Idler Rod 48 010/AY51 Clamping Plate
18 012/AY15 Riddler Rod 49# 002/CH12B Flue Collar
19 004/AX17 Ashpan 50 008/NV38 Flue Fixing Rope Seal
20 002/AY07B Front Firebar 51 012/AZ011 Serial No. Label
21 002/AY08 Deepening Bar 52# 010/TW33 Vert. Rear Flue Connector (Opt'l Extra)
22 004/AY78 Front Ash Shedding Plate 53* 010/EW51 Ash Carrier (Opt'l Extra)
23 008/KV16 RH Door Handle 54* 010/AY83 Smoke Reducing Kit (Opt'l Extra)
24 002/AY14 Door Catch Cam 55 010/AY52A External Air Manifold Kit (Opt'l Extra)
25 008/FFW015 M12 Double Coil Spring Washer 56# 005/AX093L LH Curved Panel (Optional)
26 004/ST008 Tabbed Locking Washer 57# 005/AX093R RH Curved Panel (Optional)
27 008/FFN001 M12 Half Nut 58 010/AX096 Panel Fixing Bracket
28 008/KV13 LH Door Knob 59 010/AX080 Heatshield (Opt'l Extra)
29 008/BW39/S Hinge Pin Set (4) 60# 010/AY81S Set of Low Legs (Option)
30 002/PY24 Hinge Post 61# 010/AY85S Set of High Legs (Option)
31 008/AY37 Air Control Knob 62# 010/AY87 Store Stand (Option)
Item Part Number Description
61 45
23
28 448 10
2021
16
19
31 39 40 43 37 37
37
36
42
41
56
55
59
52 49
47
48
13
11
12
62
46
6
5
7
15 25
24
26
27
29
17
18
30
32
58
51
10
14
34
35
38
60
50
3 4
22
33
57
14

®
charnwood
T: +4 4 ( 0) 19 83 5377 99 • F:+ 44 (0 )1983 537788 • SPAR ES @CH ARNWOOD .CO M • WWW.C HA RNWOO D.C OM
BISHOPS WAY, NEWPORT, ISLE OF WIGHT PO30 5WS, UNITED KINGDOM
Issue B
ISLAND II (bz) PARTS LIST
®
charnwood
I
I S L A N D
IIIII
* These items are not shown on the drawing.
# Please specify colour when ordering.
To obtain spare parts please contact your local stockist giving Model, Part Number
and Description. In case of difficulty contact the manufacturer at the address
shown.
This drawing is for identification purposes only.
Item Part No. Description Item Part No. Description
1* 008/BY35S Door Seal Set Inc. Adhesive 32 010/PX95 Riddling/Ashpan Tool
2* 008/FW29 Door Seal Adhesive 33 004/BX048 Tool Holder
3 002/CG20 Bottom Grate Bar 34 002/PX89 Riddler Knob
4 002/CG20S12 Set of Grate Bars (12) 35 004/AY21 Air Bypass Slide
5 002/CY15 Side Fire Plate 36 004/AY22-1P Primary Air Inlet Flap
6 002/BY16 Back Fire Plate 37 004/AY22-1S Secondary/Bypass Air Inlet Flap
7 004/BY24 Ash Shedding Plate 38 004/AY24-02 Flap Mounting Rod (Inc. Fixings)
8 006/BY18 Glass (Inc Seal) 39 004/BY23-07 Air Control Rod
9* 008/AY45 Glass Seal 40 004/AY23 Actuator Assembly
10 004/KV23 Glass Retainer 41 008/AY39 Upper Quattro Box Gasket
11 011/BY48S Set of Fire Bricks (4) 42 010/AY20 Upper Quattro Box
12 004/XV30 Brick Retainer 43 010/AY19 Lower Quattro Box
13 008/AY26S Set of Air Inlet Flap Pads 44# 002/BY01/A Left Hand Door Assembly
14 012/BY33 Mover Bar 45# 002/BY02/A Right Hand Door Assembly
15 002/BY30 Carrier Bar 46# 001/BZ010 Firebox (Island IIZ)
16 010/BY47 Throat Plate 47 012/TW09 Blanking Plate
17 012/AY13 Idler Rod 48 010/AY51 Clamping Plate
18 012/AY15 Riddler Rod 49# 002/CH12B Flue Collar
19 004/BX17 Ashpan 50 008/NV38 Flue Fixing Rope Seal
20 002/BY07B Front Firebar 51 012/BZ011 Serial No. Label
21 002/BY08 Deepening Bar 52# 010/TW33 Vert. Rear Flue Connector (Opt'l Extra)
22 004/AY78 Front Ash Shedding Plate 53* 010/BW51 Ash Carrier (Optional Extra)
23 008/KV16 R.H. Door Handle 54* 010/BY83 Smoke Reducing Kit
24 002/AY14 Door Catch Cam 55 010/AY52A External Air Manifold Kit
25 008/FFW015 M12 Double Coil Spring Washer 56# 005/BX093L LH Curved Panel (Optional)
26 004/ST008 Tabbed Locking Washer 57# 005/BX093R RH Curved Panel (Optional)
27 008/FFN001 M12 Half Nut 58 010/AX096 Panel Fixing Bracket
28 008/KV13 L.H. Door Knob 59# 010/BX080 Heatshield (Opt'l Extra)
29 008/BW39/S Hinge Pin Set 60# 010/BY12S Set of Low Legs (4)
30 002/PY24 Hinge Post 61# 010/BY13S Set of High Legs (4)
31 008/AY37 Air Control Knob 62# 010/BY87 Store Stand
56
55 59
49
52
47
50
48
46
57
11
16 12
62
61 8
10
45
19 44 28
23
25
24
27
2021
15
17 22
5
7
34
6
14
33
58
313940
3837
36
37
13
35
42
43
32
30
51
11
3 4
18 26
41
60
29
15

®
charnwood
T: +4 4 ( 0) 19 83 5377 99 • F:+ 44 (0 )1983 537788 • SPAR ES @CH ARNWOOD .CO M • WWW.C HA RNWOO D.C OM
BISHOPS WAY, NEWPORT, ISLE OF WIGHT PO30 5WS, UNITED KINGDOM
Issue B
ISLAND III (cz) PARTS LIST
®
charnwood
I
I S L A N D
IIIII
* These items are not shown on the drawing.
# Please specify colour when ordering.
To obtain spare parts please contact your local stockist giving Model, Part Number
and Description. In case of difficulty contact the manufacturer at the address
shown.
This drawing is for identification purposes only.
Item Part No Description Item Part No Description
1* 008/CY40S Door Seal Set Inc. Adhesive 33 004/BX048 Tool Holder
2* 008/FW29 Door Seal Adhesive 34 002/PX89 Riddler Knob
3 002/CG20 Bottom Grate Bar 35 004/CY21 Air Bypass Slide
4 002/CG20S16 Set of Grate Bars (16) 36 004/CY22P Primary Air Inlet Flap
5 010/CY14L Side Fire Plate L.H. 37 004/CY22S Secondary Air Inlet Flap
6 010/CY14R Side Fire Plate R.H. 38 004/AY22-1S Secondary/Bypass Air Inlet Flap
7 010/CY16 Back Fire Plate 39 004/CY24 Flap Mounting Rod (Inc. Fixings)
8 006/CY18 Glass (Inc Seal) 40 004/CY32 Air Control Rod
9* 008/CY41 Glass Seal 41 004/CY23 Actuator Assembly
10 004/KV23 Glass Retainer 42 008/CY39 Upper Quattro Box Gasket
11 011/CY29S Set of Fire Bricks (4) 43 010/CY20 Upper Quattro Box
12 004/XV30 Brick Retainer 44 010/CY19 Lower Quattro Box
13 010/CY31 Throat Plate 45# 002/CY01/A Left Hand Door Assembly
14 008/CY26S Set of Air Inlet Flap Pads 46# 002/CY02/A Right Hand Door Assembly
15 012/CY33 Mover Bar 47 001/CZ010 Firebox (Island IIIZ)
16 002/CY30 Carrier Bar 48 010/CY37 Blanking Plate
17 012/AY13 Idler Rod 49 010/CY61 Clamping Plate
18 012/AY15 Riddler Rod 50 002/CY45 Flue Collar
19 004/CX17L Ashpan L.H. 51 008/CY38 Flue Fixing Rope Seal
20 004/CX17R Ashpan R.H. 52 012/CZ011 Serial No. Label
21 002/CY07C Front Firebar 53# 010/CY34 Vert. Rear Flue Connector (Opt'l Extra)
22 002/CY08C Deepening Bar 54* 010/BW51 Ash Carrier (Optional Extra)
23 008/KV16 R.H. Door Handle 55* 010/CY83 Smoke Reducing Kit
24 002/AY14 Door Catch Cam 56 010/CY52A External Air Manifold Kit
25 008/FFW015 M12 Double Coil spring Washer 57# 005/CX093L LH Curved Panel (Opt'l Extra)
26 004/ST008 Tabbed Locking Washer 58# 0045/CX093R RH Curved Panel (Opt'l Extra)
27 008/FFN001 M12 Half Nut 59 010/AX096 Panel Fixing Bracket
28 008/KV13 L.H. Door Knob 60# 010/CX080 Heatshield (Opt'l Extra)
29 008/BW39/S Hinge Pin Set 61# 010/CY12S Set of Low Legs (4)
30 002/PY24 Hinge Post 62# 010/CY64S Set of High Legs (4)
31 008/AY37 Air Control Knob 63# 010/CY87 Store Stand
32 008/PX95 Riddling/Ashpan Tool
222116
34
6
18
7
19
20
45
23
25
24
26
27
8
10 62
63
11
12
13
1158
48
51
49
50
53
6056
57
47
61
59 42
43
38
37 36 41 40 31
35
3944
3 4
15
17
33
32
30
52
5
28
29
37 14
46
16
11/11/2024- Updated parts lists to Issue B

EN13240:2001
ROOMHEATERS FIRED BY SOLID FUEL
EC CERTIFICATE OF
CONFORMITY NO:
MINIMUM DISTANCE TO
COMBUSTIBLE MATERIALS:
SIDE:
REAR:
EMISSION OF CO IN
COMBUSTION PRODUCTS:
FLUE GAS TEMPERATURE:
SPACE HEATING THERMAL
OUTPUT:
ENERGY EFFICIENCY:
FUEL TYPES:
A Division of A.J.Wells & Sons Limited Registered in England No. 03809371
14
c h a r n w o o d
I S L A N D
I IIIII
Island I
AZ50-CPD-2014
450mm
600mm
0.29%
254°C
5.0kW
77.9%
Wood Logs
Island II
BZ50-CPD-2014
450mm
600mm
0.50%
290°C
8.0kW
78.0%
Wood Logs
Island III
CZ44-CPD-2014
600mm
600mm
0.30%
365°C
12.0kW
76.4%
Wood Logs
Bishops Way, Newport, Isle of Wight PO30 5WS, United Kingdom
A.J WELLS & SONS LTDA.J WELLS & SONS LTD
17

A D i v i s i o n o f A . J . W e l l s & S o n s L i m i t e d R e g i s t e r e d i n E n g l a n d N o . 0 3 8 0 9 3 7 1
charnwood
T : + 4 4 ( 0 ) 1 9 8 3 5 3 7 7 7 7 • F : + 4 4 ( 0 ) 19 8 3 5 3 7 7 8 8 • C O N TA C T U S A T W W W . C H A R N W O O D . C O M
BISHOPS WAY, NEWPORT, ISLE OF WIGHT PO30 5WS, UNITED KINGDOM
y o u r p r e m i e r d e a l e r
ISLAND I,II,III z 06.14 REV. 1
®