Chauvet DJ COLORstrip Mini User manual

User Manual

Page 2 of 18 COLORstrip/COLORstrip Mini User Manual Rev. 4
TABLE OF CONTENTS
1. Before You Begin .......................................................................................................... 3
What Is Included .............................................................................................................................3
Unpacking Instructions....................................................................................................................3
Claims..................................................................................................................................................... 3
Text Conventions ............................................................................................................................ 3
Symbols ..........................................................................................................................................3
Disclaimer .......................................................................................................................................3
Intellectual Property ........................................................................................................................ 3
Safety Notes....................................................................................................................................4
2. Introduction ................................................................................................................... 5
Product Overviews ..........................................................................................................................5
COLORstrip Overview ............................................................................................................................ 5
COLORstrip Mini Overview..................................................................................................................... 5
Product Dimensions ........................................................................................................................ 6
COLORstrip Dimensions ........................................................................................................................ 6
COLORstrip Mini Dimensions................................................................................................................. 6
3. Setup.............................................................................................................................. 7
AC Power ........................................................................................................................................ 7
Fuse Replacement .......................................................................................................................... 7
Power Linking ......................................................................................................................................... 7
Mounting ......................................................................................................................................... 8
Orientation .............................................................................................................................................. 8
Rigging ................................................................................................................................................... 8
4. Operation ....................................................................................................................... 9
Control Panel Operation..................................................................................................................9
Menu Map ....................................................................................................................................... 9
DMX Linking.................................................................................................................................... 9
Configuration (DMX) ............................................................................................................................... 9
Starting Address ..................................................................................................................................... 9
DMX Channel Assignments and Values ....................................................................................... 10
4-CH ..................................................................................................................................................... 10
Configuration (Standalone) ...........................................................................................................11
Static Color ........................................................................................................................................... 11
Automatic and Sound-Active Mode....................................................................................................... 11
Custom Color........................................................................................................................................ 12
Blackout................................................................................................................................................ 12
Reset .................................................................................................................................................... 12
IRC-6 Infrared Remote Control .....................................................................................................13
IRC-6 Operation.................................................................................................................................... 13
Master/Slave Mode .......................................................................................................................14
Master/Slave Runway Effect .........................................................................................................14
5. Maintenance .................................................................................................................15
Product Maintenance ....................................................................................................................15
6. Technical Specifications..............................................................................................16
Returns .............................................................................................................................17
Contact Us ........................................................................................................................18

COLORstrip/COLORstrip Mini User Manual Rev. 4 Page 3 of 18
1. BEFORE YOU BEGIN
What Is
Included
•COLORstrip
or
•COLORstrip Mini
•Power Cord
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Carefully unpack the product
immediately and check the container to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet.
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with Chauvet within 7 days of delivery.
Text
Conventions
Convention
Meaning
1—512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol
Meaning
Electrical warning. Not following these instructions may cause
electrical damage to the product, accessories, or the user.
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all
respects. However,
Chauvet assumes no responsibility and specifically disclaims any
and all liability to any party for any loss, damage or disruption caused by any errors or
omissions in this document, whether such errors or omissions result from negligence,
accident or any
other cause. Chauvet reserves the right to revise the content of this
document without any obligation to notify any person or company of such revision,
how
ever, Chauvet has no obligation to make, and does not commit to make, any such
revisions. Download the latest version from www.chauvetlighting.com.
The works of authorship contained in this manual, including, but not limited to, all design,
text and images are owned by Chauvet.
Intellectual
Property
© Copyright 2019 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
CHAUVET, the Chauvet logo, COLORstrip, and COLORstrip Mini
are registered
trademarks or trademarks of Chauvet & Sons, LLC. (d/b/a Chauve
t and Chauvet
Lighting) in the United States and other countries. Other company and product names
and logos referred to herein may be trademarks of their respective companies.

Page 4 of 18 COLORstrip/COLORstrip Mini User Manual Rev. 4
Safety Notes
Please read the following Safety Notes carefully before working with the product. The
Notes include important safety information about installation, usage, and maintenance.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing
the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power cord by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•
Do not touch the product’s housing when operating because it may be very hot.
•
The product is not intended for permanent installation.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket.
•The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Keep this User Manual for future use. If you sell the product to someone else, be
sure that they also receive this document.

COLORstrip/COLORstrip Mini User Manual Rev. 4 Page 5 of 18
2. INTRODUCTION
Product Overviews
COLORstrip Overview
COLORstrip Mini Overview
Power In
Fuse Holder
DMX
In/Out
Master/Slave Out
Safety Loop
Display
Menu Buttons
Power Out
Microphone
Sensitivity Knob
EXT Controller
Port
Fuse Holder
Power In
DMX
In/Out
Master/Slave Out
Safety Loop
Display
Menu Buttons
Power Out
Microphone
Sensitivity
Knob
EXT Controller
Port
LED
Indicators

Page 6 of 18 COLORstrip/COLORstrip Mini User Manual Rev. 4
Product Dimensions
COLORstrip Dimensions
COLORstrip Mini Dimensions
6 in
155 mm
38 in
965 mm
2.5 in
64 mm
6.1 in
155 mm
19 in
482 mm
2.1 in
52 mm

COLORstrip/COLORstrip Mini User Manual Rev. 4 Page 7 of 18
3. SETUP
AC Power
The COLORstrip/COLORstrip Mini has an auto-ranging power supply and it can work
with an input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the product’s
power requirements (
circuit breaker, power outlet, and wiring), use the current value
listed on the label affixed to the product’s back panel, or refer to the product’s
specifications chart. The listed current rating indicates the product
’s average current
draw under normal conditions.
•Always connect the product to a protected circuit (circuit breaker or fuse).
Make sure the product has an appropriate
electrical ground to avoid the risk
of electrocution or fire.
•
To eliminate unnecessary wear and improve its lifespan, during periods of
non-use completely disconnect the product from power
via breaker or by
unplugging it.
Never connect the product to a
rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse
Replacement
1. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
2. Pry the fuse holder out of the housing.
3. Remove the blown fuse from the holder and replace with a fuse of the exact same
type and rating.
4. Insert the fuse holder back in place and reconnect power.
Disconnect the product from the power outlet before replacing the fuse.
Power Linking
The product provides power linking via the Edison outlet located in the back of the
product. Please see the diagram below for further explanation.
Power Linking
Diagram
•You can power link up to 15 COLORstrip products on 120 VAC or up to 28
COLORstrip products on 230 VAC.
•You can power link up to 20 COLORstrip Mini
products on 120 VAC or up to
38 COLORstrip Mini products on 230 VAC.
The power linking diagram corresponds to the North American version of the
product ONLY! If using the product
in other markets, consult with the local
Chauvet distributor as power linking connectors and requirements may di
ffer in
your country or region.
1st Product
2nd Product
3rd Product
Additional
Products
Installed fuse
(held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap

Page 8 of 18 COLORstrip/COLORstrip Mini User Manual Rev. 4
Mounting
Before mounting the product, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The COLORstrip/COLORstrip Mini may be mounted in any position; however, make
sure adequate ventilation is provided around the product.
Rigging
•Before deciding on a location for the product, make sure there is easy access to the
product for maintenance and programming purposes.
•Make sure that the structure onto which you are mounting the product
can support
the product’s weight. See the Technical Specifications for weight information.
•When mounting the product overhead, always use a safety cable. Mount the
product securely to a rigging point, whether an elevated platform or a truss.
•When rigging the product onto a truss, use a mounting clamp of appropr
iate weight
capacity.
•When power linking multiple products, mount the products close enough for power
linking cables to reach.
•The bracket adjustment
knobs allow for directional adjustment when aiming the
product to the desired angle. Only loosen or tighten the bracket knobs manually.
Using tools could damage the knobs.
Mounting Diagrams
COLORstrip Mounting
Diagram
COLORstrip Mini
Mounting Diagram
Safety Cable
(such as CH-05
from Chauvet)
Mounting Clamp
(such as the CLP-
15N
from Chauvet)
Hanging/Mounting
Bracket
(also used as floor
support)
Bracket Adjustment
Knobs
Safety Cable
(such as CH-05
from Chauvet)
Mounting Clamp
(such as the CLP-
15N
from Chauvet)
Hanging/Mounting
Bracket
(also used as floor
support)
Bracket Adjustment
Knobs

COLORstrip/COLORstrip Mini User Manual Rev. 4 Page 9 of 18
4. OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the display.
Please refer to the Product Overview to see the button locations on the control panel.
Button
Function
<MODE>
Press to back out of the current menu option
<ENTER>
Press to activate a menu option or a selected value
<UP>
Press to scroll up the list of options or to find a higher value
<DOWN>
Press to scroll down the list of options or to find a lower value
Menu Map
Mode
Programming Steps
Description
ACt
A000
Blackout
A001
F000–F100
Red (strobe)
A002
F000–F100
Green (strobe)
A003
F000–F100
Blue (strobe)
A004
F000–F100
Yellow (strobe)
A005
F000–F100
Purple (strobe)
A006
F000–F100
Cyan (strobe)
A007
F000–F100
White (strobe)
A008
P000–P100
F000–F100
Color Chase 1 (speed, strobe)
A009
P000–P100
F000–F100
Color Chase 2 (speed, strobe)
A010
P000–P100
F000–F100
Color Chase 3 (speed, strobe)
A011
P000–P100
F000–F100
Color Chase 4 (speed, strobe)
A012
P000–P100
Color Chase 5 (speed)
A013
P000–P100
Color Chase 6 (speed)
A014
P000–P100
Color Chase 7 (speed)
A015
P000–P100
Color Chase 8 (speed)
A016
P000–P100
Color Chase 9 (speed)
A017
P000–P100
Color Chase 10 (speed)
A018
P000–P100
Color Chase 11 (speed)
A019
P000–P100
Color Chase 12 (speed)
A020
P000–P100
Color Chase 13 (speed)
A021 r000–r100
G000–
G100
b000–
b100
F000–
F100
Color Mix
(red, green, blue, strobe)
A022
P000–P100
Color fade (speed)
A023
All Color Chases 1–13 (speed)
SYS
SdAd
001– 512
DMX Address
SAAd
Reset
DMX Linking
The COLORstrip/COLORstrip Mini works with a DMX controller. Information about DMX is
in the CHAUVET DMX Primer, which is available from the Chauvet website
http://www.chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf.
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels the
selected DMX mode uses. If you choose a st
arting address that is too high, you could
restrict the access to some of the product’s channels.
The COLORstrip/COLORstrip Mini uses 4 DMX channels, and the
highest configurable
address is 509.
If you are not familiar with the DMX protocol, download the D
MX Primer from
www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MODE>repeatedly until SYS or ACt shows on the display.
2. Press <UP> or <DOWN> repeatedly until SYS shows on the display.
3. Press <ENTER>.
4. Press <UP> or <DOWN> repeatedly until SdAd show on the display.
5. Press <ENTER>and 001–508 will show on the display.
6. Use <UP> or <DOWN> to select the starting address.
7. Press <ENTER>.

Page 10 of 18 COLORstrip/COLORstrip Mini User Manual Rev. 4
DMX Channel Assignments and Values
4-CH
Channel
Function
Value
Percent/Setting
1
Static Colors
000

009
No function
010

019
Red 0~100%
020

029
Green 0~100%
030

039
Blue 0~100%
040

049
Yellow 0~100%
050

059
Magenta 0~100%
060

069
Cyan 0~100%
070

079
White 0~100%
Color Chases
080

089
Color Chase 1
090

099
Color Chase 2
100

109
Color Chase 3
110

119
Color Chase 4
120

129
Color Chase 5
130

139
Color Chase 6
140

149
Color Chase 7
150

159
Color Chase 8
160

169
Color Chase 9
170

179
Color Chase 10
180

189
Color Chase 11
190

199
Color Chase 12
200

209
Color Chase 13
RGB Color Mixing
210

219
Channels 2–4
Color Fade
220

229
Color Fade
Sound-Active
230 255 Sound-Active
2
Run Speed (when
Ch. 1 is 080–209)
000

127
Slow to fast
128

255
Sound-Active
Red (when
Ch. 1 is 210–219)
000 255 0~100%
Fade Speed (when
Ch. 1 is 220–229)
000 255 Slow to fast
3
Strobe (when Ch. 1 is
010–119)
003

249
Slow to fast
250

255
Sound-Active
Green (when Ch. 1 is
210–219)
000 255 0~100%
4
Blue (when Ch. 1 is
210–119)
000 255 0~100%

COLORstrip/COLORstrip Mini User Manual Rev. 4 Page 11 of 18
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
Connect the product to a suitable power outlet.
Never connect a product that is operating in any standalone mode to a DMX string
connected to a DMX controller. Product
s in standalone mode may transmit DMX
signals that could interfere with the DMX signals from the controller.
Static Color
To run the COLORstrip/COLORstrip Mini on a static color, follow the instructions below:
1. Press <MODE>repeatedly until SYS or ACt shows on the display.
2. Use <UP> or <DOWN> to select ACt.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to scroll through the menu until A001–A007 shows on the
display.
5. Press <ENTER> and F_ __will show on the display.
6. Use <UP> or <DOWN> to increase or decrease the strobe value.
•Set F000 for no strobe.
•Set F001–F099 for auto strobe, from slow to fast.
•Set F100 for sound-active strobe (Sensitivity knob must be turned up).
7. Press <ENTER>.
Automatic and
Sound-
Active
Mode
To run a color chase, do the following:
1. Press <MODE> repeatedly until SYS or ACt shows on the display.
2. Use <UP> or <DOWN> to select ACt.
3. Press <ENTER>.
4. Use <UP>or <DOWN> to scroll through the menu until A008–A020or A022–A023
shows on the display.
5. Press <ENTER> and P_ __will show on the display.
6. Use <UP> or <DOWN> to increase or decrease the program speed.
•For A008–A020, set P001–P50 for auto mode, slow to fast.
Set P051–P100 for sound-enabled auto mode, slow to fast. (Sensitivity knob
must be turned up)
•A22 has no sound mode. Set P001–P100 for fading mode, slow to fast.
•For A23, set P001–P100 for auto mode, slow to fast. Sound mode is always
enabled. Set P000 for sound mode only.
7. Press <ENTER>. For A008–A011, F_ __will show on the display.
8. Use <UP> or <DOWN> to increase or decrease the strobe value.
•Set F000 for no strobe.
•Set F001–F099 for auto strobe, from slow to fast.
•Set F100 for sound-active strobe (Sensitivity knob must be turned up).
9. Press <ENTER>.
For Sound-Active mode, turn the Sensitivity knob up until the product responds to the
beat of the music.
In Sound-Active modes, the product will only respond to low frequencies of
music (bass and drums).

Page 12 of 18 COLORstrip/COLORstrip Mini User Manual Rev. 4
Custom Color
To custom mix a color, follow the instructions below:
1. Press <MODE> repeatedly until SYS or ACt shows on the display.
2. Use <UP> or <DOWN> to select ACt.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to scroll through the menu until A021 shows on the display.
5. Press <ENTER> and r_ __will show on the display.
6. Use <UP> or <DOWN> to increase or decrease the red value.
7. Press <ENTER> and G_ __will show on the display.
8. Use <UP> or <DOWN> to increase or decrease the green value.
9. Press <ENTER> and b_ __will show on the display.
10. Use <UP> or <DOWN> to increase or decrease the blue value.
11. Press <ENTER> and F_ __will show on the display.
12. Use <UP> or <DOWN> to increase or decrease the strobe value.
•Set F000 for no strobe.
•Set F001–F099 for auto strobe, from slow to fast.
•Set F100 for sound-active strobe (Sensitivity knob must be turned up).
13. Press <ENTER>. Repeat steps 4–12 as necessary.
Blackout
To black out the COLORstrip/COLORstrip Mini, do the following:
1. Press <MODE> repeatedly until SYS or ACt shows on the display.
2. Use <UP> or <DOWN> to select ACt.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to scroll through the menu until A000 shows on the display.
5. Press <ENTER>.
Reset
To reset the COLORstrip/COLORstrip Mini, follow the instructions below:
1. Press <MODE> repeatedly until SYS or ACt shows on the display.
2. Use <UP> or <DOWN>to select SYS.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select AAAd.
5. Press <ENTER>.

COLORstrip/COLORstrip Mini User Manual Rev. 4 Page 13 of 18
IRC-6 Infrared
Remote
Control
The COLORstrip/COLORstrip Mini is compatible with the IRC-6 infrared remote control
from Chauvet. Make sure to point the IRC-
6 directly at the receiver on the front of the
product.
IRC-6 Operation
Static Color Mode
Static Color mode will enable the product to output a preset color.
To run Static Color mode:
Press <0> – <9> to choose between the different preset static colors.
Automatic/Sound-Active Mode
Automatic/Sound-Active mode will enable you to run the automatic programs on the
product. The product will also respond to music if the sensitivity knob is set high enough.
To turn on Automatic/Sound-Active mode:
1. Press <AUTO> or <SOUND> on the IRC.
2. Press <0> – <9>, or <FADE> to choose between the different programs.
To change the auto program speed:
Press <+> or <–> to increase or decrease the auto program speed.
To turn off Automatic/Sound-Active mode and return to Static Color mode:
Press <AUTO> or <SOUND> on the IRC.
COLORstrip/COLORstrip Mini IRC-6 Buttons:
Static Color Mode
Auto/Sound Mode
<0> - A007 (White)
<0> - A008
<1> - A001 (Red)
<1> - A009
<2> - A021(Amber)
<2> - A010
<3> - A004 (Yellow)
<3> - A011
<4> - A002 (Green)
<4> - A012
<5> - A006 (Cyan)
<5> - A013
<6> - A003 (Blue)
<6> - A014
<7> - A005 (Purple)
<7> - A015
<8> - A021(Pink)
<8> - A017
<9> - A021(Sunflower)
<9> - A023
<FADE> - No function
<FADE> - A022 (no response to sound)
Manual Color Control
To manually control the RGB percentage:
1. Press <MANUAL> on the IRC.
2. Press <R> (red), <G> (green), or <B> (blue) to choose the color.
3. Press <+> or <–> to increase or decrease the percentage of each color.
Miscellaneous Operation
To adjust the strobe rate of the program:
1. Press <STROBE> on the IRC.
2. Press <+> or <–> to increase or decrease the strobe rate.
3. Press <STROBE> again to turn off the strobe.
To black out the lights:
Press <BLACK OUT> on the IRC.
This will turn off all the lights until the button is pressed again.
NOTE: The IRC will not respond to any inputs when Black Out is activated. If the remote
does not respond when a button is pressed, try pressing <BLACK OUT>. You
may have inadvertently activated Black Out.

Page 14 of 18 COLORstrip/COLORstrip Mini User Manual Rev. 4
Master/Slave
Mode
The Master/Slave mode allows a single COLORstrip/COLORstrip Mini product (the
“master”) to control the actions of one or more COLORstrip/COLORstrip Mini products
(the “slaves”) without the need of a DMX controller. The master product
will be set to
operate in either Stand-Alone mode or with the IRC-6, while the slave products
will be
set to operate in Slave mode. Once set and connected, the slave products will operate in
unison with the master product.
Configure the products as indicated below.
Slave products:
1. Press <MODE> repeatedly until SYS or ACt shows on the display.
2. Press <UP> or <DOWN> repeatedly until SYS shows on the display.
3. Press <ENTER>.
4. Press <UP> or <DOWN> repeatedly until SdAd shows on the display.
5. Press <ENTER>, and 001–508 will show on the display.
6. Set the DMX address to 001.
7. Connect the DMX input of the first slave product to the DMX output of the master
product. SLA will show on the display.
8. Connect the DMX input of the subsequent slave products to the DMX output of the
previous slave product.
9. Finish setting and connecting all the slave products.
Master product:
1. Set the master product to run in auto or sound mode.
2. Make the master product the first product in the DMX daisy chain.
•Configure all the slave product
s before connecting the master to the daisy
chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller
may interfere with the signals from the
master.
•Do not connect more than 31 slaves to the master.
Master/Slave
Runway Effect
The Master/Slave Runway Effect mode allows a single COLORstrip/COLORstrip Mini
product (the “master”) to control the actions of one or more COLORstrip/COLORstrip
Mini products (the “slaves”) in a runway effect
without the need of a DMX controller. The
master product will be set to operate on specific programs in either Automatic or Sound-
Active mode, while the slave products
will be set to operate in Slave mode. Once set
and connected, the program will run smoothly from product to product.
Configure the products as indicated below.
Slave products:
1. Press <MODE> repeatedly until SYS or ACt shows on the display.
2. Press <UP> or <DOWN> repeatedly until SYS shows on the display.
3. Press <ENTER>.
4. Press <UP> or <DOWN> repeatedly until SdAd shows on the display.
5. Press <ENTER>, and 001–508 will show on the display.
6. Set the DMX address to 001.
7. Connect the DMX input of the subsequent slave products to the Master/Slave
output of the previous slave product.
8. Finish setting and connecting all the slave products.
Master product:
1. Set the master product to run in auto or sound mode, A014–A020.
2. Connect the DMX input of the first slave product to the Master/Slave output of the
master product. SLA will show on the displays of the slaves.
•
Configure all the slave products before connecting the master to the daisy
chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operat
ion because the controller may interfere with the signals from the
master.
•
Do not connect more than 31 slaves to the master.

COLORstrip/COLORstrip Mini User Manual Rev. 4 Page 15 of 18
5. MAINTENANCE
Product
Maintenance
Dust build-
up reduces light output performance and can cause overheating. This can lead
to reduction of the light source’s life and/or
mechanical wear. To maintain optimum
performance and minimize wear, clean your lighting product
s at least twice a month.
However, be aware that usage and environmental conditions could be contributing factors
to increase the cleaning frequency.
To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass
cleaner, or isopropyl alcohol.
5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.

Page 16 of 18 COLORstrip/COLORstrip Mini User Manual Rev. 4
6. TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
COLORstrip
38 in (965 mm)
2.5 in (64 mm)
6 in (155 mm)
4.5 lb (2 kg)
COLORstrip Mini
19 in (482 mm)
2.1 in (52 mm)
6.1 in (155 mm)
3.3 lb (1.5 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100 to 240 VAC, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
COLORstrip
Consumption
72 W
73 W
Operating Current
0.6 A
0.3 A
Power linking current
(products)
8 A (15 products) 8 A (28 products)
Fuse
F 1 A, 250 V
F 1 A, 250 V
COLORstrip Mini
Consumption
38 W
40 W
Operating Current
0.3 A
0.2 A
Power linking current
(products)
8 A (20 products) 8 A (38 products)
Fuse
F 1 A, 250 V
F 1 A, 250 V
Power I/O
U.S./Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (U.S.)
Local plug
Light Source
Type
Power
Lifespan
LED
0.25 W
100,000 hours
Color
Quantity
(COLORstrip)
Quantity
(COLORstrip Mini)
Current
Red
128
64
20 mA
Green
128
64
20 mA
Blue
128
64
20 mA
Photometrics
Parameter
COLORstrip
COLORstrip Mini
Beam Angle
28°
37° x 33°
Field Angle
43°
68° x 51°
Illuminance @ 2 m
1,104 lux
1,192 lux
Thermal
Maximum External Temp.
Cooling System
104 °F (40 °C)
Convection
DMX
I/O Connectors
Channel Range
3-pin XLR
4
Ordering
Product Name
Item Code
UPC Number
COLORstrip
10051063
781462214111
COLORstrip Mini
10051064
781462214128

COLORstrip/COLORstrip Mini User Manual Rev. 4 Page 17 of 18
R
ETURNS
To get support or return a product:
•If you are located in the U.S., contact Chauvet World Headquarters.
•If you are located in the UK or Ireland, contact Chauvet Europe Ltd.
•If you are located in Benelux, contact Chauvet Europe BVBA.
•If you are located in France, contact Chauvet France.
•If you are located in Germany, contact Chauvet Germany.
•If you are located in Mexico, contact Chauvet Mexico.
•If you are located in any other country, DO NOT contact Chauvet. Instead, contact
your local distributor. See www.chauvetdj.com for distributors outside the U.S., UK,
Ireland, Benelux, France, Germany, or Mexico.
If you are located outside the U.S., UK, Ireland,
Benelux, France, Germany, or
Mexico, contact your distributor of record and follow their instructions on how to
return Chauvet products to them. Visit our website www.chauvetlighting.com for
contact details.
Call the corresponding Chauvet Technical Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product. Be
prepared to
provide the model number, serial number, and a brie
f description of the cause for the
return.
To submit a service request online, go to www.chauvetdj.com/service-request.
Send the merchandise prepaid, in its original box, and with its original packin
g and
accessories. Chauvet will not issue call tags.
Clearly label the package with the RMA number. Chauvet will refuse any product
returned without an RMA number.
Write the RMA number on a
properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write the following information on a piece of paper
and place it inside the box:
•Your name
•Your address
•Your phone number
•RMA number
•A brief description of the problem
Be sure to pack the product properly. An
y shipping damage resulting from inadequate
packaging will be your responsibility. FedEx packing or double-
boxing are
recommended.
Chauvet reserves the right to use its own
discretion to repair or replace returned
product(s).

Page 18 of 18 COLORstrip/COLORstrip Mini User Manual Rev. 4
C
ONTACT
US
General Information
Technical Support
Chauvet World Headquarters
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
Voice: [phone]
Fax: [phone]
Email: [e-mail]
Website www.chauvetdj.com
Chauvet Europe Ltd
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.chauvetdj.eu
Chauvet Europe BVBA
Address: Stokstraat 18
9770 Kruishoutem
Belgium
Voice: [phone]
Email: [e-mail]
Website: www.chauvetdj.eu
Chauvet France
Address: 3, Rue Ampère
91380 Chilly-Mazarin
France
Voice: [phone]
Email: [e-mail]
Website: www.chauvetdj.eu
Chauvet Germany
Address: Bruno-Bürgel-Str. 11
28759 Bremen
Germany
Voice: [phone]
Email: [e-mail]
Website: www.chauvetdj.eu
Chauvet Mexico
Address: Av. de las Partidas 34-3B
(Entrance by Calle 2)
Zona Industrial Lerma
Lerma, Mexico C.P. 52000
Voice: [phone]
Email: [e-mail]
Website: www.chauvetdj.mx
Outside the U.S., U.K., Ireland, Benelux, France, Germany, or Mexico, contact the
dealer of record. Follow the instructions to request support or to return a product. Visit
our website for contact details