Chauvet DJ GigBAR Flex User manual

Quick Reference Guide

EN
1
GigBAR Flex QRG Rev. 1
QUICK REFERENCE GUIDE
About This Guide
The GigBAR Flex Quick Reference Guide (QRG) has basic product information such as mounting, menu
options, and DMX values. Download the User Manual from www.chauvetdj.com for more details.
Disclaimer
The information and specifications contained in this QRG are subject to change without notice.
Safety Notes
These Safety Notes include important information about installation, use, and maintenance.
Contact
Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux, contact your distributor to request support
or return a product. Visit www.chauvetdj.com for contact information.
What is Included
• This product is not intended for permanent installation.
• ONLY connect this product to a grounded and protected circuit.
• DISCONNECT from power before cleaning or replacing the fuse.
• DO NOT look at the light source when the product is on.
• Make sure the power cord is not crimped or damaged.
• Never disconnect this product from power by pulling on the cord.
• When mounting this product overhead, ALWAYS use a safety cable.
• DO NOT allow flammable materials close to the product when it is operating.
• DO NOT touch the product’s housing when it is on because it will be hot.
• The voltage of the outlet to which you areconnectingthis productmust bewithinthe
range stated on the decal or rear panel of the product.
• This product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose this product to rain or moisture.
• In the event of a serious operating problem, stop using immediately.
• Always mount this product in a location with adequate ventilation, at least 20 in (50
cm) from adjacent surfaces.
• Be sure that no ventilation slots on the unit’s housing are blocked.
• Never connect this product to a dimmer or rheostat.
• Replace the fuse with the same type and rating.
• Never carry the productby the power cord. Use only the handle to carry this product.
• The maximum ambient temperature is 104 °F (40 °C). Do not operate this product
at higher temperatures.
• DO NOT open this product. It contains no user-serviceable parts.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
• GigBAR Flex
•Powercord
• Carrying bag
• Wireless foot switch
•IRC-6
• Warranty Card
• Quick Reference Guide
00

2
EN
QUICK REFERENCE GUIDE
GigBAR Flex QRG Rev. 1
To Begin
Unpack your GigBAR Flex and make sure you have received all parts in good condition. If the box or
contents appear damaged, notify the carrier immediately, not Chauvet.
Overview
1
2
3
4
LED Display
DMX In/Out
Menu
Buttons
Power Out Adjustment
Knobs x4
Power In
Wireless
Antenna
Adjustable Pass- Through
for Tripod mounting
9-Volt Battery
Cover
02

EN
3
GigBAR Flex QRG Rev. 1
QUICK REFERENCE GUIDE
AC Power
This product has an auto-ranging power supply that can work with an input voltage range of 100–240 VAC,
50/60 Hz.
Power Linking
For the maximum number of GigBAR Flex that can be power linked at 120 V or at 230 V, see the User
Manual or the label on the product.
Fuse Replacement
1. Disconnect the product from power.
2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
3. Pry the safety cap out of the housing.
4. Remove the blown fuse from the clip on the front of the safety cap and replace with a fuse of the
exact same type and rating.
5. Re-insert the fuse holder and reconnect power.
IRC-6 (Infrared Remote Control)
The GigBAR Flex is fully compatible with the Infrared Remote Control (IRC-6) from CHAUVET DJ. For
more information on the IRC-6 or to download instructions, go to www.chauvetdj.com.
Mounting
Before mounting this product, read the Safety Notes. This product can be mounted to most tripods,
trussing (using appropriate clamps and with/without the included mounting brackets) or can be used floor/
surface mounted.
Mounting Diagram
To eliminate wear and improve its lifespan, during periods of disuse completely
disconnect the product from power via breaker or by unplugging it.
IR Sensor
Microphone
Mounting
Clamp
(such as CLP-
15 from
Chauvet)
Bracket
Adjustment
Knob
Tripod (sold separately)
Insertion Point w/
Adjustment Knob for
Tightening

4
EN
QUICK REFERENCE GUIDE
GigBAR Flex QRG Rev. 1
Control Panel Description
Menu Map
BUTTON FUNCTION
<MENU> Exits from the current menu or function
<UP> Navigates upwards through the menu list and increases the numeric value when
in a function
<DOWN> Navigates downwards through the menu list and decreases the numeric value
when in a function
<ENTER> Enables the currently displayed menu or sets the currently selected value into the
selected function
MODE PROGRAMMING LEVELS DESCRIPTION
AUTO Mixed
Effect AM01
F 01–F 99
Selects the auto mixed effect
show
AM02
SOUND
Mixed Effect SM01 Selects the sound mixed effect show
SM02
Auto Par
Effect
SHOW
AP01–AP07 Selects the Par show
Auto Derby
Effect AK01 Selects the Derby auto speed
Auto Strobe
Effect AS01–AS22 Selects the auto strobe shows
Auto
Par+Derby APK1 Selects the Par and Derby auto show speed
Auto Par +
Strobe APS1 Selects the Par and strobe show speed
Auto Derby +
Strobe AKS1 Selectsthe Derbyandstrobe auto who speed
Par + Derby
+ Strobe APKS Selects the Par, Derby, and strobe speed
Sound Par
Effect SP01–SP07 Set Pars to Sound mode
SoundDerby
Effect SK01 Sets Derby Lights to Sound mode
Sound
Strobe Effect SS01–SS22 Sets strobes to Sound mode and selects effect speed
Sound Par +
Derby SPK1 Sets Pars and Derby Lights to Sound mode
Sound Par +
Strobe SPS1 Sets Pars and strobes to Sound mode
SoundDerby
+ Strobe SKS1 Sets Derby Lights and strobes to Sound Mode
Par + Derby
+ Strobe SPKS Sets Pars, Derby Lights and strobes to Sound mode

EN
5
GigBAR Flex QRG Rev. 1
QUICK REFERENCE GUIDE
DMX Linking
The GigBAR Flex can work with a DMX controller. Instructions for connecting and configuring this product
for DMX operation are in the User Manual. If you are not familiar with DMX or DIP-switch configuration,
download the DMX Primer from www.chauvetdj.com.
Starting Address
To ensure full access to the two channels available in DMX mode, the highest recommended DMX address
is 510.
Master/Slave Connection
The GigBAR Flex uses the DMX data connection for its Master/Slave mode. Instructions for connecting
and configuring this product for Master/Slave operation are in the User Manual.
General
COLOR
Setting CoLo
R000–R255 Sets both Par and
Derby red values Note:ONLY
3 of the 4
colors may
be used at
the same
time.
G000–G255 Sets both Par and Derby green
values
B000–B255 Sets both Par and
Derby blue values
U000–U255 Sets the UV values for the Par
and strobes
DMX Mode
Setting d001–d512
3 CH Sets DMX starting address;
selects the DMX personality DMX
range restricted by number of
channels in the selected DMX
mode
8 CH
20 CH
Master/Slave
Setting Slav Sets to Slave mode
System
Options Sys
dSET 1234 Changes arrangement of pods
rSEt Resets to factory defaults
WiFi on Turns on/off Wi-Fi antenna for
wireless footswitch
off
MODE PROGRAMMING LEVELS DESCRIPTION

6
EN
QUICK REFERENCE GUIDE
GigBAR Flex QRG Rev. 1
Wireless Foot-Switch Operation
The included wireless foot-switch provides quick access to preset colors, color-change programs, and
sound-activation through the GigBAR Flex microphone. To use the foot-switch:
1. Connect the GigBAR Flex to power. Turn the wireless foot-switch on.
2. Raise the wireless antennas located on the GigBAR Flex and the foot-switch.
3. Press pedal #1 (Auto) to activate Auto program controls. When working, all the lights will begin in
Auto mode (AM01).
4. Use the chart below to activate the desired function..
PEDAL ACTION FUNCTION
1
(Auto)
1 x press Auto mode Pars, Derby Lights and
strobes (AM01)
2 x press AP01
3 x press AP02
4 x press AK01
5 x press APK1
2
(Sound)
1 x press Auto mode Pars, Derby Lights and
strobes (SM01)
2 x press SP01
3 x press SP02
4 x press SK01
5 x press SPK1
3
(Color)
1 x press Red, no strobe
2 x press Green, no strobe
3 x press Blue, no strobe
4 x press UV, no strobe
5 x press Yellow, no strobe
6 x press Pink, no strobe
7 x press Cyan, no strobe
8 x press Dark Pink, no strobe
9 x press Dark Blue, no strobe
10 x press White, no strobe
4
(Blackout) N/A Immediately turns OFF all the light
fixtures

EN
7
GigBAR Flex QRG Rev. 1
QUICK REFERENCE GUIDE
DMX Values
20Ch
The GigBAR Flex footswitch will work properly in any mode, with a maximum
unobstructed distance of 50 ft (15.24 m). You must turn on the WiFi on the
GigBAR Flex before using the footswitch.
CHANNEL FUNCTION VALUE PERCENT/SETTING
1
Par 1
000 255 Red 0-100% Note: You are able
to use a maximum
of 3 colors at a time
2000 255 Green 0-100%
3000 255 Blue 0-100%
4000 255 UV 0-100%
5000 127
128 239
240 249
250 255
Dimmer 0-100%
Strobe speed, slow to fast
Strobe to sound
RGB 100%
6
Par 2
000 255 Red 0-100% Note: You are able
to use a maximum
of 3 colors at a time
7000 255 Green 0-100%
8000 255 Blue 0-100%
9000 255 UV 0-100%
10 000 127
128 239
240 249
250 255
Dimmer 0-100%
Strobe speed, slow to fast
Strobe to sound
RGB 100%
11 Derby 1
Control
000 024
025 049
050 074
075 099
100 124
125 149
150 174
175 199
200 224
225 255
Blackout
Red
Green
Blue
Red + Green
Red + Blue
Green + Blue
Red + Green + Blue
Automatic (single colors only)
Automatic (two colors at a time)
12 Derby 1
Strobe Rate 000 009
010 239
240 255
No function
Strobe, 0-30 Hz
Strobe to sound
13 Derby 1
Rotation
000 004
005 127
128 133
134 255
Stop
Rotate clockwise, slow to fast
Stop
Rotate counter-clockwise, slow to fast
14 Derby 2
Control
000 024
025 049
050 074
075 099
100 124
125 149
150 174
175 199
200 224
225 255
Blackout
Red
Green
Blue
Red + Green
Red + Blue
Green + Blue
Red + Green + Blue
Automatic (single colors only)
Automatic (two colors at a time)
15 Derby 2
Strobe Rate 000 009
010 239
240 255
No function
Strobe, 0-30 Hz
Strobe to sound

8
EN
QUICK REFERENCE GUIDE
GigBAR Flex QRG Rev. 1
8Ch
16 Derby 2
Rotation
000 004
005 127
128 133
134 255
Stop
Rotate clockwise, slow to fast
Stop
Rotate counter-clockwise, slow to fast
17 Strobe
Patterns
000 009
010 029
030 069
050 069
070 089
090 109
110 129
130 149
150 169
170 189
190 209
210 255
Blackout
Auto Strobe Program 1
Auto Strobe Program 2
Auto Strobe Program 3
Auto Strobe Program 4
Auto Strobe Program 5
Auto Strobe Program 6
Auto Strobe Program 7
Auto Strobe Program 8
Auto Strobe Program 9
All Strobing
Strobe to sound mode
18 White Strobe
Dimmer 000 255 White 0-100% Note: Channels 18
& 19 cannot be
used at the same
time.
19 UV Strobe
Dimmer 000 255 UV 0-100%
20 Strobe
Speed 000 255 Slow to fast (for CH18 or CH19)
CHANNEL FUNCTION VALUE PERCENT/SETTING
1Pars and
DerbyColor
000 255 Red 0-100% Note: You are able
to use a maximum
of 3 colors at a time
2000 255 Green 0-100%
3000 255 Blue 0-100%
4000 255 UV 0-100%
5Pars and
Derby
Strobe
Controls
000 127
128 239
240 249
250 255
Dimmer 0-100%
Strobe speed, slow to fast
Strobe to sound
RGB 100%
6DerbyMotor
Rotation
000 004
005 127
128 133
134 255
Stop
Rotate clockwise, slow to fast
Stop
Rotate counter-clockwise, slow to fast
7White Strobe
Speed 000 054
055 255 White strobe dimmer, 0–100%
White strobe speed, slow to fast Note: Channels 7
& 8cannot be used
at the same time.
8UV Strobe
Speed 000 054
055 255 UV strobe dimmer, 0–100%
UV strobe speed, slow to fast
CHANNEL FUNCTION VALUE PERCENT/SETTING

EN
9
GigBAR Flex QRG Rev. 1
QUICK REFERENCE GUIDE
3Ch
CHANNEL FUNCTION VALUE PERCENT/SETTING
1LED
Operation
000 009
010 119
120 229
230 234
235 239
240 255
No function
Auto mixed mode 1, fast to slow
Auto mixed mode 2, fast to slow
Sound mixed mode 1
Sound mixed mode 2
Show setting,when channels 2 and 3 activated
2 Operation
000 009
010 026
027 043
044 060
061 077
078 094
095 111
112 128
129 145
146 161
162 178
179 196
197 213
214 230
231 255
No function
Pars on ONLY, doing all single Par show
Derby Lights on ONLY
Strobes on ONLY, doing all single strobe show
Auto Pars and Derby Lights ONLY
Auto Pars and strobes ONLY
Auto strobes and Derby Lights ONLY
Pars, Derby Lights, and strobes
Sound Par effect
Sound Derby effect
Sound strobe effect
Sound Par + Derby
Sound Par + strobe
Sound Derby + strobe
Sound pars, Derby and strobes
3 Auto Speed 000 255 Speed, when 061–111 in channel 2