Chauvet Geyser RGB User manual

User Manual

Page 2 of 14 Geyser™ RGB User Manual (Rev. 1)
TABLE OF CONTENTS
1. Before You Begin...........................................................................................................3
What Is Included .........................................................................................................................3
Unpacking Instructions................................................................................................................3
Claims.................................................................................................................................................3
Text Conventions ........................................................................................................................3
Symbols......................................................................................................................................3
Disclaimer...................................................................................................................................3
Product at a Glance.....................................................................................................................4
Safety Notes ...............................................................................................................................4
2. Introduction....................................................................................................................5
Overview.....................................................................................................................................5
Dimensions.................................................................................................................................6
3. Setup...............................................................................................................................7
AC Power....................................................................................................................................7
Fuse Replacement...............................................................................................................................7
Mounting.....................................................................................................................................8
Orientation...........................................................................................................................................8
Rigging................................................................................................................................................8
4. Operation........................................................................................................................9
Control Panel Operation..............................................................................................................9
Menu Map...................................................................................................................................9
Configuration (DMX)....................................................................................................................9
Starting Address ..................................................................................................................................9
DMX Channel Modes, Assignments, and Values.......................................................................10
8-Channel..........................................................................................................................................10
Configuration (Standalone)........................................................................................................11
Automatic Mode.................................................................................................................................11
Master/Slave Mode............................................................................................................................11
Wireless Remote Control....................................................................................................................11
5. Technical Information..................................................................................................12
Fogger Maintenance .................................................................................................................12
Storage.....................................................................................................................................12
6. Technical Specifications..............................................................................................13
Returns.....................................................................................................................................14
Contact Us................................................................................................................................14

Geyser™ RGB User Manual (Rev. 1) Page 3 of 14
1.BEFORE YOU BEGIN
What Is
Included
•Geyser™ RGB
•Power Cord
•FC-W Wireless Remote Control
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Carefully unpack the product immediately
and check the container to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and
included accessories) appear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not CHAUVET®.
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as
missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of delivery.
Text
Conventions
Convention
Meaning
1~512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol Meaning
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this User Manual
are subject to change
without notice. CHAUVET® assumes no responsibility or liabil
ity for any errors or
omissions, and reserves the right to revise or recreate this manual at any time.
Download the latest version from www.chauvetlighting.com.
© Copyright 2012 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Author Date Editor Date
A. Leon 9/19/12 S. Diaz 9/21/12

Page 4 of 14 Geyser™ RGB User Manual (Rev. 1)
Product at a
Glance
Use on Dimmer

Auto Programs

Outdoor Use

Fixed voltage (120 V or 230 V)

Sound Activated

Replaceable Fuse

DMX

User-Serviceable

Master/Slave

Duty Cycle

Safety Notes
These notes include important information about the mounting, usage, and maintenance
of this product; read before using the product.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing the
fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a safety
cable.
•Make sure there are no flammable materials close to the product when operating.
•Do not touch the product’s housing when operating because it may be very hot.
•Do not mount the product on a flammable surface (linoleum, carpet, wood, paper,
carton, plastic, etc.)
•The product’s nozzle is very hot during operation and it remains hot for a long time after
operation has stopped.
•The fog exits the nozzle at a very high temperature. Keep a minimum distance of 6.5 ft
(2 m) from the nozzle to the nearest object.
•Do not use the product as a space heater.
•Do not drink or become in contact with the fog fluid. If you do, call your local emergency
service (911 in the US) for help.
•
Do not add perfume, alcohol, gasoline, or any other flammables to the fog fluid.
•Always make sure that the voltage of the outlet to which you are connecting the product
is within the range stated on the decal or panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not expose
the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in (50 cm)
from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Make sure there is adequate fog fluid in the machine to prevent pump and heater
damage.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product by the power cord or any moving part. Always use the handles.
•The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate the product
at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Contact the nearest authorized technical assistance center.
•This product is not intended for permanent installation.
•Use only CHAUVET® water-based fog fluid.
•
Drain the tank before transporting the product.
•Keep this User Manual for future use. If you sell the product to another user, be sure to
give this document to the next owner.
•Fog Cleaner Quart (FCQ) was specifically developed by CHAUVET® to clean your
Geyser™ RGB. Make sure you use FCQ regularly to increase the life of your fogger.

Geyser™ RGB User Manual (Rev. 1) Page 5 of 14
2.INTRODUCTION
Overview
LED Display
3-pin DMX
In/Out
Nozzle and LEDs
Fluid Tank
On/Off Switch
Safety Eye
Loop
Remote Control
Receiver Port
Fuse Holder
Power In
Handles
5-pin DMX
In/Out
Alternate
Safety Eye Loop
Attachment Point
Safety Cable
Attachment Point
(Underside)

Page 6 of 14 Geyser™ RGB User Manual (Rev. 1)
Dimensions

Geyser™ RGB User Manual (Rev. 1) Page 7 of 14
3.SETUP
AC Power
The Geyser™ RGB
has a fixed voltage power supply and it can work with an input
voltage of either 120 V, 60 Hz or 230 V, 50 Hz, depending on the specific model.
To determine the product’s power requirements (circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product’s panel, or refer to
the product’s specifications chart. The listed current rating indicates the product’s
average current draw under normal conditions.
Always connect the product to a protected circuit (circuit breaker or fuse). Make
sure the product has an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect the product
to a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0~100% switch.
Fuse
Replacement
Disconnect the product from power before replacing the fuse.
1. Disconnect the product from power.
2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
3. Pry the fuse holder out of the housing.
4. Remove the blown fuse from the holder.
5. Replace with a fuse of the exact same type and rating.
6. Insert the fuse holder back in place and reconnect power.
A spare fuse is not included; however, the safety cap has room for a spare.
Always replace a blown fuse with the same type and rating.
Installed fuse
(held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap

Page 8 of 14 Geyser™ RGB User Manual (Rev. 1)
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The Geyser™ RGB may be mounted in
an overhead mounting/downward fog jet, floor
mounting/vertical fog jet, or floor mounting/horizontal fog jet.
For best results, remove the fluid tank from the holder and set it upright on an
adjacent surface when mounting the Geyser™ RGB in an inverted position.
Rigging
•Before deciding on a location, always make sure there is easy access to the product
for maintenance and fluid replenishment.
•Make sure that the structure or surface onto which you are mounting the product
can support the product’s weight (see the Technical Specifications).
•When mounting the product overhead, always use a safety cable. Mount the
product securely to a rigging point, such as an elevated platform or a truss.
•When rigging the product onto a truss, you should use mounting clamps of
appropriate weight capacity. Three 13-mm holes are on the bottom of the product,
which are appropriate for this purpose.
•The rubber feet also serve as floor supports. When mounting the product on the
floor, make sure that the product and cables are away from people and vehicles.
Mounting Diagram
Floor Mounting – Vertical Fog Jet
Floor Mounting – Horizontal Fog Jet
Overhead Mounting – Downward Fog Jet

Geyser™ RGB User Manual (Rev. 1) Page 9 of 14
4.OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the
display.
Button
Function
<MENU> Selects an operation mode or to backs out of the current menu option

(
<UP>
) Scrolls up the list of options or selects a higher value

(<DOWN>)Scrolls down the list of options or selects a lower value
<ENTER> Activates a menu option or a selected value
Menu Map
Mode Programming Steps Description
DMX Mode
Addr
1
~
512
Selects the DMX starting address
Color Program CoLo
rAnd
Selects random color program
Co 1~Co 9 Selects preset colors
Fluid Sensor orL
on
Selects fluid sensor to on or off
oFF
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you
choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
The Geyser™ RGB uses up to 8 DMX channels in its 8-Channel mode, which defines the
highest configurable address to 505.
If unfamiliar with DMX, download the DMX Primer from www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU>repeatedly until Addr shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the starting address.
HEAT shows on the display when you first turn the product on and intermittently
during the heat-
up time of the fog fluid; however, you can configure the product
during this time.

Page 10 of 14 Geyser™ RGB User Manual (Rev. 1)
DMX Channel Modes, Assignments, and Values
8-Channel
Channel Function Value Setting
1 Fog
000 009
No function
010 255
Fog on
2 Red
000 009
No function
010 255
0~100%
3 Green
000 009
No function
010 255
0~100%
4 Blue
000 009
No function
010 255
0~100%
5 Color Mixing
000 009
No function
010 255
Color mixing
6 Auto Speed
000 009
No function
010 255
Speed, slow to fast
7 Strobe
000 009
No function
010 255
Strobe, slow to fast
8 Dimmer
000 009
No function
010 255
0~100%

Geyser™ RGB User Manual (Rev. 1) Page 11 of 14
Configuration
(Standalone)
Set the product to Automatic mode to control without a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
Never connect a product that is operating in any standalone mode t
o a DMX string
connected to a DMX controller. Product
s in standalone mode may transmit DMX
signals that could interfere with the DMX signals from the controller.
Automatic Mode
To select either the preset color program or one preset color to illuminate the fog
, follow
the instructions below:
1. Press <MENU>repeatedly until CoLo shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select rAnd (for random colors) or Co 1~Co 9 (to choose
one of nine preset colors).
Master/Slave
Mode
The Master/Slave mode allows a single Geyser™ RGB
unit (the “master”) to control the
actions of one or more Geyser™ RGB
units (the “slaves”) without the need of a DMX
controller. The master unit will be set to operate in Automatic or Manual m
ode, while the
slave units will be set to operate in DMX m
ode. Once set and connected, the slave units
will operate in unison with the master unit.
Configure the units as indicated below.
Slave units:
1. Set the DMX address to 1.
2. Connect the DMX input of the first slave unit to the DMX output of the master unit.
3. Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
4. Finish setting and connecting all the slave units.
Master unit:
1. Set the master unit to operate in Automatic or Manual mode.
2. Make the master unit the first unit in the DMX daisy chain.
•Configure all the slave units before
connecting the master unit to the DMX
daisy chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller
may interfere with the signals from the
master unit.
•Do not connect more than 31 slave units to the master unit.
Wireless
Remote
Control
To trigger fog output using the wireless remote control, do the following:
1. Plug the wireless receiver into the Remote Control Receiver port on the side of the
Geyser™ RGB.
2. On the wireless transmitter, press the button assigned to the Geyser™ RGB. The
Geyser™ RGB emits fog for as long as you hold down the button.
To learn how to configure the receiver and operate the transmitter, download the FC-W
Wireless Remote Controller instructions from www.chauvetlighting.com.

Page 12 of 14 Geyser™ RGB User Manual (Rev. 1)
5.TECHNICAL INFORMATION
Fogger
Maintenance
Do not allow the fogger
machine to become contaminated. After every 40 hours of
continuous operation, CHAUVET® recommends running
a cleaning solution composed
of 80% distilled water and 20% distilled vinegar through the system to prevent the
accumulation of particulate matter in the heating element.
The recommended cleaning procedure is as follows:
1. Empty all fog fluid from the machine.
2. Add cleaning solution to tank.
3. Plug unit in and allow it to warm up.
4. Run the unit in a well-
ventilated area until the tank is almost empty. Do not allow the
pump to run dry.
5. Cleaning is now complete. Refill with fog fluid. Run the machine briefly to clear any
cleaning solution from the pump and heater.
•Fog Cleaner Quart (FCQ) was specifically developed by CHAUVET® to clean your
Geyser™ RGB. Make sure you use FCQ regularly to increase the life of your
fogger.
Storage
Before storing the product
, run distilled water (not tap water) through the system as
described in the cleaning procedure
above. This will help to avoid any particles
condensing inside the pump or heater.
It is strongly recommended to test-run the
machine on a monthly basis in order to
achieve its best fogging condition.

Geyser™ RGB User Manual (Rev. 1) Page 13 of 14
6.TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
20 in (510 mm)
14.7 in (375 mm)
9.8 in (250 mm)
21 lbs (9.6 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Model-specific
120 VAC, 60 Hz
or 230 VAC, 50 Hz
Fixed
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
1500 W
1500 W
Operating/Inrush current
11.6 A/11.6 A
6.2 A/6.2 A
Fuse
F 15 A, 250 V
F 8 A, 250 V
Power I/O
US/Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (US)
Local plug
Light Source
Type
Power
Lifespan
LED
3 W
50,000 hours
Color
Quantity
Current
Red
7
800 mA
Green
7
800 mA
Blue
7
800 mA
Photo Optic
Parameter
Illuminance @ 2 m
4870 lx
Operation/Capacity/
Consumption
Heat-up Time
Tank Capacity
Fluid Consumption
4 min
0.66 gal (2.5 l)
8 min/1 l
Misc.
Output
4000 cfm
Thermal
Maximum External Temp.
Cooling System
104° F (40° C)
Convection
DMX
I/O Connectors
Connector Type
Channel Range
3- and 5-pin XLR
Sockets
8
Ordering
Product Name
Item Code
UPC Number
Geyser™ RGB
05070561
781462209094
Geyser™ RGB 220 V
05070567
781462209155

Page 14 of 14 Geyser™ RGB User Manual (Rev. 1)
To return a product or request support:
•In the U.S., contact CHAUVET® World Headquarters.
•In the UK or Ireland, contact CHAUVET® Europe Ltd.
•In any other country, DO NOT contact CHAUVET®. Contact your distributor. See
www.chauvetlighting.com for distributors outside the U.S., United Kingdom, or
Ireland.
If you live outside the U.S., United Kingdom, or Ireland, contact your distributor of
record and follow their instructions on how to return CHAUVET® products to
them. Visit our website for contact details.
Returns
Call the corresponding CHAUVET® Technical
Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product
. Be prepared to
provide the model number, serial number, and a brief description of the cause for the
return.
You must send the merchandise prepaid, in
its original box, and with its original packing
and accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any product
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write
the following information on a piece of paper
and place it inside the box:
•Your name
•Your address
•Your phone number
•The RMA number
•A brief description of the problem
Be sure to pack the product
properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. FedEx packing or double-boxing are
recommended.
CHAUVET® reserves the
right to use its own discretion to repair or replace
returned product(s).
Contact Us
World Headquarters
CHAUVET®
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
United Kingdom & Ireland
CHAUVET® Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [e-mail]
Technical Support
Email: [e-mail]
World Wide Web
www.chauvetlighting.com
World Wide Web
www.chauvetlighting.co.uk