Checkpoint Smart-1 series Instruction Manual

Classification [Protected] P/N:707495
© 2018 Check Point Software Technologies Ltd. All rights reserved.
For a list of our trademarks, please refer to: www.checkpoint.com/copyright.html.
For a list of our Third Party Copyright notices, please refer to: www.checkpoint.com/3rd_party_copyright.html
Smart-1 Installing and Removing
AC Power Supply Units
707495
Protected
2018
This document is for appliance models Smart-1 525, Smart-1 5050, and
Smart-1 5150.
Safety Instructions
•Lift the appliance with assistance. To avoid injury, do not attempt to lift the
appliance by yourself.
•Opening or removing the appliance cover, while the appliance is powered on
may expose you to a risk of electric shock.
•Do not operate the appliance without the cover for more than five minutes.
Operating the appliance without the cover can result in component damage.
•Many repairs may only be done by a certified service technician. Only
perform troubleshooting and simple repairs as authorized in your product
documentation, or as directed by the technical support.
•We recommend that you always use an antistatic mat and antistatic strap on
your wrist, while working on components inside the appliance.
•To ensure proper operation and cooling, all bays in the appliance and
cooling fans must be always populated with a component or a blank.
For more information, see the
Enterprise Products Safety, Environmental, and
Regulatory Information
booklet supplied in the original appliance shipping
carton.

2
Important - We recommend that only experienced personnel
install or remove hardware components. Installing or removing
components incorrectly can permanently damage the Security
Management Appliance.
Important - Make sure that you are electromagnetically grounded
when working with hardware components of the appliance. ESD
(electrostatic discharge) can damage the appliance.
AC Power Supply Unit (PSU)
Smart-1 525, Smart-1 5050 and Smart-1 5150 Security Appliances support up to
two AC redundant power supply units (PSUs).
Security
Management
Appliance
Output power
and efficiency
of each PSU
Supported
Input
AC Voltage
Smart-1 525 350 W (Platinum) 100-240 V AC, 50/60 Hz
Smart-1 5050 495 W (Platinum) 100-240 V AC, 50/60 Hz
Smart-1 5150 750 W (Titanium) 100-240 V AC, 50/60 Hz
Notes:
•The appliances support PSU redundancy. One PSU is sufficient for the
normal appliance operation.
•Installing AC PSU and DC PSU together is not supported and triggers a
mismatch event - the AC PSU handle flashes green five times and turns off.
•When only one working PSU is installed, it must be installed in the first PSU
bay - see the markings on the appliance cover.
To ensure proper appliance cooling, leave the failed PSU in place until you
get the replacement PSU. This prevents the cooling air from escaping.

3
•When two PSUs are installed, and the appliance is powered on, you must
remove and replace only one PSU at a time.
•When two PSUs are installed, they must be the same type and have the
same maximum output power.
•When two PSUs are installed, they must receive the same input AC voltages.
•When two identical PSUs are installed, power to the appliance is supplied
equally from both PSUs to maximize efficiency.
AC PSU
Item Description
1 Release latch
2 External power connector (to connect the power cable)
3 Internal power connector (to insert into the appliance)
4 Translucent handle that illuminates with different colors

4
Indicator lights for AC PSU
Each AC PSU has a translucent handle. This handle shows different colors to
indicate if AC power is received, or a PSU fault occurred.
Indicator
handle light
Description
Steady green
A valid AC power source is connected to the AC PSU.
The AC PSU is operational.
Flashing green
and turns off
When you hot-add an AC PSU, the AC PSU handle flashes
green five times at 4 Hz rate and turns off.
This indicates that there is a mismatch between this
hot-plugged AC PSU and the other installed AC PSU. The
mismatch is in any of these PSU characteristics: efficiency,
feature set, health status, or supported voltage.
Make sure that both AC PSUs are the same.
Notes:
•When correcting a PSU mismatch, replace only the AC
PSU with the flashing indicator. Swapping the other AC
PSU to make a matched pair can result in an error
condition and unexpected appliance shutdown.
•When two identical AC PSUs receive different input
voltages, they can output different wattages, and
trigger a mismatch event.
•Installing AC PSU and DC PSU together is not
supported and triggers a mismatch event.

5
Indicator
handle light
Description
Flashing amber
Indicates a problem with the AC PSU.
Off
AC power is not connected to the AC PSU.
Removing an AC PSU
Important Note -If you do not install the replacement PSU at this time, leave
the failed PSU in place to ensure proper appliance cooling. This prevents the
cooling air from escaping.
1. You must follow the Safety instructions (on page 1).
2. Disconnect the power cable from the power source.
3. Open the retention strap that secures the power cable to the PSU.
4. Disconnect the power cable from the PSU.
5. Remove the hook-and-loop straps that hold and secure the system cables,
if they interfere with PSU removal.
6. Press and hold the release latch on the PSU.
7. Pull the PSU out from the appliance.

6
Important - The appliance needs one working PSU for the normal
operation. When two PSUs are installed, and the appliance is
powered on, remove and replace only one PSU at a time.
Important - When only one working PSU is installed, it must be
installed in the first PSU bay - see the markings on the appliance
cover.
Installing an AC PSU
Note - When you install, hot-swap, or hot-add a new PSU, wait for 10-15
seconds for the appliance to recognize the PSU and determine its status. The
PSU redundancy may not occur until discovery is complete. Wait until the new
PSU is discovered and enabled before you remove the other PSU. The PSU
status indicator turns green to signify that the PSU is functioning properly.
1. You must follow the Safety instructions (on page 1).
2. Make sure that both PSUs are of the same type and have the same
maximum output power.
Note -The maximum output power (in Watts) is listed on the PSU label.
3. Slide the new PSU into the appliance until the PSU is fully seated, and the
release latch snaps into place.
4. If you opened the hook-and-loop straps, close them to secure the system
cables.
5. Connect the power cable to the PSU.

7
6. Make a loop and secure the power cable to the PSU using the retention
strap.
7. Plug the power cable into a power outlet.