Chemin'Arte Lounge User manual

www.cheminarte.com
ELECTRIC HEATER
INSTRUCTION MANUAL
Model: Lounge, Lounge médium and Ovalia ref 146/184/185/186
ATTENTION:
1. Find a location for the electric heater that is protected from direct sunlight.
2. Do not plug the electric heater into the power outlet before you read all
instructions.

Important
-Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool
-Do not use this heater if it has been dropped;
-Do not use if there are visible signs of damage to the heater;
-Use this heater on a horizontal and stable surface, or fix it to the wall, as applicable.
-WARNING: Do not use this heater in small rooms when they are occupied by persons not capable of
leaving the room on their own, unless constant supervision is provided.
-WARNING: To reduce the risk of fire, keep textiles, curtains, or any other flammable material a
minimum distance of 1 m from the air outlet.
-The heater must not be located immediately below a socket outlet.
-Do not use this heater with a programmer, timer, separate remote-control system or any other device
that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned
incorrectly.
-This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
NOTE: If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a hazard.
CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance
must not be supplied through an external switching device, such as a timer, or connected to a circuit that is
regularly switched on and off by the utility.
CAUTION—Some parts of this product can become very hot and cause burns. Particular attention has to
be given where children and vulnerable people are present.
WARNING: In order to avoid overheating, do not cover the heater.
Electrical Parameter
Power supply: AC220-240V
Frequency: 50-60Hz
Power: 2000W

Parts list
REF NO
DESCRIPTION
QTY Lounge
QTY Lounge
medium /Ovalia
A
5 PCS
3 PCS
B
5 PCS
3 PCS
C
1 PC
1 PC
Installation
Please be aware: that no products should be sealed against the wall/opening as this can effect the
performance of the heater unit.
Minimum Installation Height:
From floor level to bottom edge of product, Minimum 300mm.
This suite is supplied with a wall fixing Bracket.
The suite can be installed at any height as long as it is not below the recommended 300mm. (Please note
the 700mm measurement is given as a common installation height).
The recommended installation height is a minimum of 300mm from the floor level to the underside of the
hearth.
Warning: Installing this product below 300mm will cause overheating issues.
The suite is designed as a wall mounted suite; it is not suitable to be installed at floor level.

Installation:
This model is provided with a wall mounting bracket along with x5 screws and wall plugs.
PLEASE NOTE: The screws and plugs provided are only suitable for a solid wall fixing.
If the installation is onto a hollow/stud wall, we recommend that heavy duty wall anchors or equivalent are
used.
To install the product:
1. Measure 700mm from the floor level up the wall, Mark this measurement with a pencil.
2. Place the bottom edge of the wall bracket on the 700mm mark, level using a spirit level and mark and
drill the x5 fixing holes.
3. Using the correct wall fixings screw and fix the wall bracket in place.
4. Locate the x5 slots in the rear of the product, carefully align these slots with the prongs on the wall
bracket, lift and slot the product into place.
5. Locate the power cable socket on the bottom right hand side, underneath the hearth on the fire, and
plug the power lead in.
6. The product is now ready to use.
Operating Instructions
Once the electric heater has been properly installed and connected to a ground electrical outlet, it is ready to
operate.
Note: Ensure the circuit breakers for the power supply are turned on.
The heater controls are located right of the heater outlet.
Control Panel
LED Screen Remote Control

O/I: Press this switch, the unit power-on. When the O/I switch is turned off, all other functions will stop
even though the buttons may be in the ON position.
: Press this button, the unit will enter standby mode. The unit will beep and the indicator light will
be on. Then you can select the following functions as desired. Press again to turn off the heater.
: For modification time function - Press this button, the ‘SUN’on the LED screen starts to
twinkle. Press up or down button to the desired date, and press button to select, press
button to cancel. After set the desired date, press button switch to the ‘hour’position. Press or
button to the desired hour. Press button switch to the ‘minute’position. Press or button to
the desired minute. Press or button to complet date setting.
NOTE: The date will be reset after power interrupt.
: For automatic working time setting function - There are 10 time periods you can set to make the
unit work automatically. Press this button, time serial number starts to twinkle. The ‘ON’on the
LED screen lights up. Press or button to the desired serial number. Press button again, the
‘SUN’on the LED screen starts to twinkle. Press up or down button to the desired date, and press
button to select, press button to cancel. After set the desired date, press button switch to the
‘hour’position. Press or button to the desired hour. Press button switch to the ‘minute’position.
Press or button to the desired minute. At this time you have completed the boot time setting. Press
button again, the ‘ON’extinguished and the ‘OFF’lights up. Complete the shutdown time in the same
way. Finally, you need to set a temperature which stop heating. Press or button to the desired
temperature. When desired ambient temperature is reached, the heater will automatically stop heating.
: For Window detection function - Press this button to turn on the window detection function.
During the heating process, if the room temperature drops obviously caused by the outdoor cold
air blowing, such like open windows or open the door. In order to save energy, the heater will automatically
stop heating. The corresponding icon on the screen will twinkle. Press again to turn off the window
detection function to normally heating.
: For reset function - Press this button to clear the Timing parameters.
: For heat function - Press this button to turn on the heat function. Press again to turn off.
: For timer function - Press this button to turn on the timer function. Press again to turn off.
Note: the working state of the time period is the same as that before start timer function. That is to say, adju
st the working state you want and turn on the timer function, then the machine will work according to your
working state in the time period.
: For flame function - Press this button to turn on the flame. Press again to turn off.

: For flame effect function - Press this button to change flame effect. Press again to decrease the
flame intensity. There are 4 light intensities for your selection. The flame optics will go lower
under the sequence of 4,3,2 and 1. Pressing the button again will go higher under the sequence of 1,2,3 and
4.
NOTE:After the display screen is extinguished, it can be activated by any key.
NOTE: In the absence of timing mode, you can press or button to the desired temperature directly.
When desired ambient temperature is reached, the heater will automatically stop heating.
Fast Menu:
：Press the standby button and the heating button, the unit can heating immediately.
Maintenance:
WARNING: Completely disconnect power before attempting any maintenance or cleaning, to
reduce the risk of fire or electric shock. Maintenance should only be performed by a certified
technician.
Cleaning:
Before cleaning any parts of the fireplace make sure to first turn off the controls and then unplug the
unit from power source.
CAUTION: Wait until the unit has completely cooled before attempting any cleaning.
Cleaning Glass Panel: Remove dust with clean dry cloth. Remove fingerprints and other marks
from glass door by using a clean damp cloth. Do not use abrasive cleaners or spray liquids on glass
door surfaces.
Metal and metal painted parts should be cleaned with clean damp cloth only. Do not use abrasive
cleaners or spray liquids on these surfaces.

Information requirements for electric fixed local space heaters
Model identifier(s): RO2716-48Z
Item
Symbol
Value
unit
Item
unit
Heat output
Type of heat input, for electric storage local
space heaters only (select one)
Nominal heat
output
Pnom
2,0
kW
manual heat charge control, with
integrated thermostat
[no]
Minimum heat
output
(indicative)
Pmin
0
kW
Manual heat charge control with
room and/or outdoor temperature
feedback
[no]
Maximum
continuous heat
output
Pmax,c
2,0
kW
Electronic heat charge control with
room and/or outdoor temperature
feedback
[no]
Auxiliary
electricity
consumption
Fan assisted heat output
[no]
At nominal heat
output
elmax
0
kW
Type of heat output/room temperature
control (select one)
At minimum
heat output
elmin
0
kW
single stage heat output and no room
temperature control
[no]
In standby
mode
elsb
0
kW
Two or more manual stages, no room
temperature control
[no]
with mechanic thermostat room
temperature control
[yes]
with electronic room temperature
control
[no]
electronic room temperature control
plus day timer
[no]
electronic room temperature control
plus week timer
[yes]
Other control options (multiple selections
possible)
room temperature control, with
presence detection
[no]
room temperature control, with open
window detection
[yes]
with distance control option
[no]
with adaptive start control
[no]
with working time limitation
[yes]
with black bulb sensor
[no]
Contact details:
www.cheminarte.com