CHIEF FWDSK110 User manual

INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Small Flat Panel Steel Stud Wall Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
FWDSK110

FWDSK110 Installation Instructions
2
DISCLAIMER
CSAV, Inc., and its affiliated corporations and subsidiaries
(collectively, "CSAV"), intend to make this manual accurate and
complete. However, CSAV makes no claim that the information
contained herein covers all details, conditions or variations, nor
does it provide for every possible contingency in connection
with the installation or use of this product. The information
contained in this document is subject to change without notice
or obligation of any kind. CSAV makes no representation of
warranty, expressed or implied, regarding the information
contained herein. CSAV assumes no responsibility for
accuracy, completeness or sufficiency of the information
contained in this document.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for the installation of this kit can result in serious personal
injury or damage to equipment! It is the installer’s
responsibility to make sure the structure to which this kit is
attached can support five times the combined weight of all
equipment.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to this accessory does not exceed
40 lbs (18.1 kg).
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme

Installation Instructions FWDSK110
3
TOOLS REQUIRED FOR INSTALLATION AND PARTS
TOGGLERĂ
x1
I/M
A (1)
D (4)
G (4)
C (2)
E (4)
(3/16")
B (4)
J (3)
F (4)
K (3)
H (4)
M (1)
(M4 x 12)
L (3)
(1/2" x 3/4")
(1/4"-20 x 1 3/4")
1/2" (Ø13mm)
(3/16")
(M4 x 20)
(M4 x 20)
(1/4")
(1/2" x 3/8")
(1/4"-20 SNAPTOGGLE BB)

FWDSK110 Installation Instructions
4
Site Requirements
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum reguirements for installation of display mounts onto a
steel stud structure. If the structure or its components do not meet these requirements contact the mount manufacturer for specific
instructions before attempting installation. It should also be noted that no other equipment should be mounted to the same stud.
Figure 1
Drywall
1/2" minimum
Drywall Thickness
Display Mount Installation Location
FRONT
(Both Sides of Stud)
(Must be centered on stud)
There must be a minimum of
1 7/8" (48mm) clearance
inside wall
Steel Stud (2 x 4 / 25ga minimum)
Stud type and structural strength must conform to the North American
Specification for the Design of Cold-Formed Steel Structural Members.
If back side of wall is unfinished, drywall must be installed
to a minimum of one stud left and right of the stud(s)
being used to install the mount. Drywall must be
secured to studs with screws 12" on center
[362 S 125 18, C-Shaped, S-Stud Section]

Installation Instructions FWDSK110
5
Mount Installation
After determining the site meets the installation requirements:
1. Identify desired mounting location on wall.
2. Using a stud finder or similar method locate studs.
3. Align mounting holes in mount with studs making sure
mounting holes are centered on studs. (See Figure 2)
4. Mark location of three mounting holes on wall.
5. Drill three 1/2" (Ø13mm) holes. (See Figure 2)
Figure 2
6. Hold metal channel on anchor (L) flat alongside
plastic straps and slide channel through hole.
(See Figure 3)
Figure 3
7. Holding plastic straps on anchor (L), pull anchor away
from wall until channel rests flush behind wall making
sure anchor channel is positioned vertically on stud as
show in figues below. (See Figure 4)
8. Slide plastic cap on anchor (L) towards wall until
flange of cap is flush with wall. (See Figure 4)
Figure 4
9. Snap off plastic straps on anchor at wall by pushing
side to side, snapping off straps level with flange of
plastic cap. (See Figure 5)
10. Repeat steps 6 through 9 for each mounting hole.
1/2" (Ø13mm) x3
Mounting holes
centered on
studs
5
(A) x1
(L) x3
Drywall
Plastic Straps
Plastic Cap
Steel Stud
Drywall
Anchor Metal Channel
SIDE VIEW
(M) x3

FWDSK110 Installation Instructions
6
Figure 5
11. Place mount over anchors and align mounting holes
in display mount with holes in anchors. (See Figure 6)
12. Place flat washer (J) onto Phillips pan head screws
(K).
13. Insert Phillips pan head screws (K) with flat washer (J)
through mounting hole in display mount and into
anchor (L) and tighten until flush against mount. DO
NOT overtighten!
WARNING: IMPROPER INSTALLATION CAN LEAD TO
EQUIPMENT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Overtightening of
mounting hardware can damage the steel studs. DO NOT
overtighten mounting hardware!
Figure 6
Display Installation
The mounting holes on the back of your display will either be
flush with the back surface, or recessed into the back surface.
Refer to the applicable installation procedure.
Flush Mount Display
WARNING: IMPROPER INSTALLATION CAN LEAD TO
EQUIPMENT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display! Proper screws will
easily and completely thread into display mounting holes.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
EQUIPMENT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Inadequate thread
engagement in display may cause display to fall! Back out
screws ONLY as necessary to allow installation of Centris
bracket!
1. Ensure Centris bracket is able to swivel and tilt easily, yet
still be tight enough to hold display in desired position.
Adjust as required before proceeding.
See "ADJUSTMENTS" for detail.
2. Using Phillips screwdriver, carefully install two screws
(E) into the upper mounting holes on the display.
Thread screws completely into display, then back out
3 complete turns. (See Figure 7)
3. Pick up and align display so that screws (E) (installed
on the back of the display in the previous step) fit into
the mounting holes on the Centris bracket; rotate the
bracket as required (See Figure 7). Lower the display
into place.
Figure 7
4. Using Phillips screwdriver, install two remaining
screws (E) through the lower mounting holes in
Centris bracket and into display.
5. Tighten all four screws (E). Do not overtighten!
6. Proceed to "CABLE MANAGEMENT."
RECESSED MOUNTING HOLES
1. Ensure Centris bracket is able to swivel and tilt easily, yet
still be tight enough to hold display in desired position.
Adjust as required before proceeding.
See "ADJUSTMENT" for detail.
Plastic Straps
Steel Stud
Drywall
Anchor Metal Channel
Plastic Cap
SIDE VIEW
Steel Stud
Drywall
Anchor Metal Channel
Display Mount
SIDE VIEW
(K) x 3
(J) x 3
(A) x 1
(E) x 2
Centris Bracket

Installation Instructions FWDSK110
7
2. Carefully place display face down on protective
surface.
3. Determine depth of recessed mounting holes relative
to back surface of display (against which Centris head
will contact). (See Figure 8)
4. Select proper length spacer and screw.
(See Figure 8)
NOTE: All spacers used should be the same length. If
the recess depths result in multiple spacer
lengths, then select the longer spacer.
5. Place the four selected spacers over each of the
mount holes on the back of the display.
6. Pick up and orient the mount (A) so that the mounting
holes in the Centris bracket are aligned with the holes
in the spacers; rotate the bracket as required. (See
Figure 8)
Figure 8
WARNING: IMPROPER INSTALLATION CAN LEAD TO
EQUIPMENT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display! Proper screws will
easily and completely thread into display mounting holes.
7. Using Phillips screwdriver, install four screws (D or H)
through the mounting holes in Centris bracket,
through the spacers (F or G), and into the display.
(See Figure 8)
8. Tighten all four screws. Do not overtighten!
CABLE MANAGEMENT
1. Attach all cables to display.
CAUTION: Ensure that adequate cable slack exists for
movement of display, and that cables will not be pinched by
installation of cover (C) or screws (E).
2. Carefully insert cables in cavity located in lower
portion of mount arm (See Figure 9).
3. Using Phillips screwdriver, install cover (10) with two
screws (20). (See Figure 9)
Figure 9:
ADJUSTMENTS
Swing Arm
PIVOT / SWING
1. Using 3/16" hex key, slightly loosen or tighten the
adjustment screw(s) as necessary (See Figure 10).
Figure 10
Centris Head
1. If previously attached, disconnect cables from display, then
remove display.
2. Using Phillips screwdriver, slightly loosen or tighten
the adjustment screw as necessary (See Figure 11).
Figure 11
(A) x 1
(D or H) x4
(F or G) x 4
Centris Bracket
(E) x 4
Cable Path
(typical)
(C) x 2
Adjustment Screws
Adjustment Screw
Phillips Screwdriver

FWDSK110 Installation Instructions
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P800.582.6480 / 952.894.6280
F877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P+31 40 2668620
F+31 (0) 40 2668615
Asia Pacific A Room 30I, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112
P+86-755-8996 9226 ; 8996 9236 ; 8996 9220
F+86-755-8996 9217
8832-000218 RevC
©2007 Chief Manufacturing
www.chiefmfg.com
08/07