CHIEF MSP-KTPHD Series User manual

M S P - K T P H D - X X Q U I C K S T A R T G U I D E
This Quick Start Guide is meant to provide only an overview of the various installation steps.
ALWAYS read the Installation Instructions for each individual product within this kit before
beginning the Installation.
WARNING: Exceeding the weight capacity
can result in serious personal injury or
damage to equipment! It is the installer’s
responsibility to make sure the combined
weight of all components attached to the
MSP-KTPHD-XX up to (and including) the
display does not exceed 35 lbs (15.87 kg) per
interface..
MSP-KTPHD-FS MSP-KTPHD-GM MSP-KTPHD-DC
Pole Attachment for MSP-KTPHD-FS - Assemble pole
to base using one 3/8-16 x 1" flat head cap screw.
Pole attachment for MSP-KTPHD-GM -Locate desired point on
surface where mount is to be installed. Drill a 1/2" diameter hole
through surface. Align grommet mount base plates with hole in
surface. Slide one 3/8-16 x 6" hex head cap screw upward
through lower grommet plate, through hole in surface and through
upper grommet plate. Place pole, provided with array accessory,
onto upper grommet plate aligning threaded hole in pole bottom
with threaded end of 3/8-16 x 6" hex head cap screw. Thread 3/8-
16 x 6" hex head cap screw into pole bottom and tighten with 9/16"
wrench to secure pole and grommet plates to surface.
pole upper grommet plate
lower grommet plate
3/8-16 x 6" screw
1a 1b
1c
Pole attachment for MSP-
KTPHD-DC NOTE: In order
to reduce the chance of
scratching to the mounting
surface, bumpers may be
installed. However,
installation of bumpers is
optional.
Remove adhesive from
underside of bumpers.
Attach bumpers to underside
of desk clamp.
Use 7/32" hex key to install
3/8-16 x 1" flat head cap
screw through the opening
on top of desk clamp and
into bottom of mounting pole
Place desk clamp over desired mounting location on desk.
Turn clamp screw until the clamp is secured to the desk as tightly
as possible.
pole
base
3/8 x 16 x 1" screw
pole
3/8 x 16 x 1"
desk clamp
clamp screw
bumpers

MSP-KTPHD Quick Start Guide
2
Adjustments
To adjust display Roll, Pitch and Yaw:
a. Disconnect all wires and cables.
b. Remove display.
c. Using a hex head wrench, turn the tension
adjustment screw clockwise to increase tension or
counter-clockwise to decrease tension.
d. Re-install display, wires and cables.
a. Route cables and wires to display.
b. Route cables and wires through cable
management covers.
c. Snap cable management covers onto pole.
2
3
4
Place mount against pole, with clamp on opposite side of pole.
Using 5/32" hex key, loosely assemble with three 1/4-20 x 1-
1/4" button head cap screws.
mount
pole
pole clamp
1/4-20 x 1-1/4" screws x 3
8800-003381 Rev01
2023 Legrand | AV
www.legrandav.com
02/2023
Chief, a brand of Legrand
6436 City West Parkway, Eden Prairie, MN
55344
• P: 800.582.6480 / 952.225.6000 • F:877.894.6918 /
952.894.6918
Legrand | AV and its affiliated corporations and subsidiaries (collectively “Legrand
| AV”), intend to make this manual accurate and complete. However, Legrand |
AV makes no claim that the information contained herein covers all details, con-
ditions or variations, nor does it provide for every possible contingency in connec-
tion with the installation or use of this product. The information contained in this
document is subject to change without notice or obligation of any kind. Legrand |
AV makes no representation of warranty, expressed or implied, regarding the in-
formation contained herein. Legrand | AV assumes no responsibility for accuracy,
completeness or sufficiency of the information contained in this document.
a. Start two M4 x 8mm Phillips pan head screws
(included in hardware kit) into upper mounting
holes in display back.
NOTE: Leave at least 1/8" of each screw protruding out back
of display.
b. Align two screws in display back with upper
mounting holes in Centris cup and lower display
until screws are seated in lower area of teardrop
mounting holes. (See Figure 4)
c. Install two more of the same screws through lower
mounting holes in Centris cup and into display
back. (See Figure 4)
d. Tighten all hardware.
4 x 8mm screws x 2
4 x 8mm screws x 2
3a
3b
3c
5b
5a
5a
5b
5c
5c
5
4c
4c