CHIEF TPA-111 User manual

INSTALLATION INSTRUCTIONS
CHIEF MANUFACTURING INC. 8832-000019 (Rev. B)
1-800-582-6480 952-894-6280 FAX [phone] Chief Manufacturing
8401 EAGLE CREEK PARKWAY, STE. 700 www.chiefmfg.com
SAVAGE, MINNESOTA 55378 USA 4/05
TRUSS PITCH-ADJUSTABLE MOUNT
TPA-111
Figure 1
(1) PLATE, back (4) SCREW, Pan Head, M4-.7X20mm
(1) PLATE, assembly, pitch-adjustable (4) Nylon, Spacer, .5 X .194 ID X .0375”
(1) ADAPTER, VESA Flat Panel Interface (4) SCREW, cap, hex head, 5/16-18 X ½”
(4) SCREW, Pan Head, M4-.7X10mm (4) NUT, Nylock, 5/16-18
BEFORE PROCEEDING: Unpack the carton, verify contents shown in Figure 1 and read installation
instructions completely. If you are missing any of the listed components, please contact Customer Service at
1-800/582-6480.
CAUTION! PLASMA DISPLAYS ARE EXTREMELY FRAGILE.
WARNING! ALL COMPONENTS MUST BE SECURELY FASTENED TO A
STRUCTURAL MEMBER CAPABLE OF SUPPORTING 4 TIMES
THE COMBINED WEIGHT OF ALL COMPONENTS PLUS THE
EQUIPMENT BEING MOUNTED. IF IT CANNOT SUPPORT THIS
WEIGHT, THE STRUCTURE MUST BE REINFORCED.
THE MAXIMUM WEIGHT TO BE INSTALLED ON THE MOUNT
IS 150 POUNDS (68.04 KG).

Installation Instructions TPA-111
2
Installation for 75mm and 100mm Mounting:
1. Securely anchor the back plate to framework using
Chief TPK accessory clamps or equivalent rated
for the required load (see Figure 2).
2. Install the pitch-adjustable plate on the back plate
and secure using four 5/16-18 X ½” hex head cap
screws (see Figure 3).
3. For displays with a flat mounting surface (see
Figure 6), place adapter bracket over four
mounting holes and secure using four M4 X 10
PHCS screws, as follows:
• For 75mm, see Figure 4 and Figure 5.
• For 100mm, see Figure 4 and Figure 7.
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
5/16-18 X ½” hex head cap screws
Pitch-Adjustable
Plate Assembly
Back Plate
Back Plate
VESA Flat Panel
Interface Adapter

Installation Instructions TPA-111
3
4. For displays with a recessed mounting surface,
place four 5 X .194 ID X .0375” Nylon spacers over
four mounting holes (see Figure 8).
5. For displays with a recessed mounting surface,
place VESA interface adapter bracket over four
spacers and secure using four M4 X 20 PHCS
screws (see Figure 9).
VESA Flat Panel Interface Adapter To Pitch-
Adjustable Mount Installation
1. Install VESA flat panel interface adapter on pitch-
adjustable mount (see Figure 9).
2. Secure VESA flat panel interface adapter to pitch-
adjustable mount using four 5/16-18 Nylock Nuts.
Pitch-Adjustable Mount Installation And
Adjustment
1. Securely anchor the pitch-adjustable mount to
framework (see WARNING!).
2. Loosen tilt adjustment screws. Tilt the mount to
desired position. Tighten tilt adjustment screws.
See Figure 10.
3. If desired, use a ¼” bolt to secure tilt at 0 degrees,
5 degrees, or 10 degrees (see Figure 10).
Figure 8
Figure 9
Figure 10
5/16-18 Nylock Nuts
10 degree Tilt
(Inside Hole)
Tilt
Adjustment
Screw
Tilt
Adjustment
Screws
5 degree Tilt
(Middle Hole)
0 degree Tilt
(Outside Hole)
N
ylon
Spacers
VESA Interface
Adapter Bracket
N
ylon
Spacers