Child Craft Crib'N'Double Bed User manual

CHILD CRAFT INDUSTRIES, INC.
P.O. Box 444, Salem, IN USA 47167-0444
PH: 812-883-3111 - FAX: [phone] - http://www.childcraftind.com
ASSEMBLY DIRECTIONS AND PARTS LIST
READ ALL INSTRUCTIONS WITH CARE BEFORE STARTING THE ASSEMBLY PROCEDURE.
 YOU WILL NEED A #2 PHILLIPS SCREWDRIVER, A STANDARD SLOTTED SCREWDRIVER, A 3/8 (10mm) WRENCH,
AND THE ENCLOSED ALLEN WRENCHS (AA
AA
A& HH
HH
H).
PARTS ENCLOSED IN HARDWARE BAG (NOTED WHEN SHOWN ACTUAL SIZE)
ABCD
(actual size)
(4) Hexhead
Machine
Screw
(actual size) (actual size)
(10) Allenhead K-D Bolts
(actual size)
(4) Allenhead K-D Bolts
(8) K-D Bolt
Plugs
PARTS ENCLOSED IN CARTON
E
(1) Allen Wrench
FGHI
J
K
(1) Stationary Side L
(1) Front Side M
(1) Crib Stretcher S
(for use on Toddler Bed only)
(1) Crib Spring R
plastic pouch
(6) Phillips
Head Machine
Screw
(2) 4-Position Spring
Bracket
(1) Allen Wrench
(5mm)
(4) Allenhead Bolts
(4) Insert Nuts
(4) Hole Button
Covers
(actual size)
(actual size)
(actual size) (actual size)
CCH01788:08/00 JCHEp6.5 1
CRIBNDOUBLE BED
CONVERTS TO TODDLER BED OR
FULL SIZE HEADBOARD & FOOTBOARD
(1) Foot Top Dowel T
child craft
(1) Foot Post P
Left
(1) Foot Post Q
Right
(1) Headboard N(1) Footboard O
(5/32)
36101, 36301
H00280
H01105
H00254 H00109
H00122
H00251(B)
H01169
H01168
H00956
H01123
H00136
H00250(W)

Carefully remove and lay out all hardware and parts. Check quantities and match the Hardware List and the Parts List. NOTE:
During the assembly process whenever using screws or bolts, check each with the Hardware List by letter and size
identification. Place each screw or bolt on the diagram of the item which is sketched actual size. Be sure to use the
proper size specified in the assembly directions. If a part is missing or broken contact your Child Craft dealer or Child Craft,
P.O. Box 444, Salem, IN 47167-0444 USA, 812-883-3111, for replacement part(s) or instructional literature. Before making this
contact identify your CribnDouble Bed by the model identification number stamped on the label attached to the inside face of
Footboard Obottom rail. Make note of all identification numbers and include this information with your request. DO NOT
SUBSTITUTE PARTS!
Record your model identification number here for future identification: Model #______________________________________
STEP 1 - DIAGRAM 1: INSTALL HARDWARE ON FOOT POSTS
Attach 4-position Spring
Bracket Gusing three
Phillips Head Machine
Screws F, to Foot Post
Left Pand Foot Post
Right Qas shown.
Tighten securely.
STEP 2 - DIAGRAM 2: ATTACH FOOT POSTS TO FOOTBOARD AND HEADBOARD
CCH01788:08/00
Attach Foot Post Qto
Footboard Oas
shown. Lay both
pieces horizontal on a
soft surface (carpet)
and start by inserting K-
D Bolt Ethrough its
receiving hole in Foot
Post Qand into the fac-
tory installed threaded
insert in Footboard O.
Start threads three or
four turns using Allen
Wrench A. Do not
fully tighten at this
time. Insert K-D Bolt
Dthrough the receiv-
ing hole located in the
rectangular rout and
into the threaded insert
(factory installed in both
Foot Posts Q& P).
Once K-D Bolts D&
Eare properly aligned
and both are started into
their threaded inserts,
tighten both securely
using Allen Wrench A.
Follow the same proce-
dure for attaching Foot
Post Pto Headboard
N. Insure all K-D Bolts
are tightened securely
before continuing with
next step.
PREPARATION
2
F
FF
GQ
Threaded inserts
Threaded inserts
G
P
Start K-D Bolt EE
EE
Einto its
threaded insert (and
leave loose) before in-
stalling K-D Bolt DD
DD
D.
O
QE
A
D
D
P
N
Connected View
G
Threaded Insert
will receive E
Threaded Insert
will receive D

K-D Bolt Plugs C. Insert K-D Bolts Einto receiving holes in the Stationary Side L and into receiving holes in Headboard N& Footboard O. Keep
K-D Bolts Eout just far enough to allow K-D Bolt Plug Cto be fully inserted into their receiving holes. Align the threaded hole in K-D Bolt Plug C
with the threads on K-D Bolt E. Tighten four or five revolutions but do not fully tighten at this time.
Install K-D Bolts Dinto their Factory Installed Threaded Inserts at bottom using the same methods you used during Step 2.Tighten all K-D Bolts (D
& E) at this time.
STEP 4
Install Foot Top Dowel Tas shown. Start K-D Bolts Einto K-D Bolt Plugs Cbut do not tighten completely at this time.
Attach Front Side Mto Footpost Right Qand Footpost Left P.
Insert K-D Bolts Einto receiving holes in Footposts P& Qand into receiving holes in Front Side M. Insert K-D Bolt Plugs Cinto their receiving
holes aligning the threaded hole with the threads on K-D Bolt E.
Tighten all K-D Bolts (D& E) at this time.
CCH01788:08/00 3
STEP 3 - DIAGRAM 3: ASSEMBLE CRIB
Attach Headboard Assembly (G, N& P) and Footboard Assembly (G, O& Q) to Stationary
Side Las shown. Follow Diagram 3 closely. Attach components at top using K-D Bolts Eand
N
C
E
L
E
C
D
E
E
Q
Dowel Pin
C
T
Factory installed
E
D
E
P
WHEN ASSEMBLY IS COMPLETE -
TIGHTEN ALL K-D BOLTS SECURELY
Dowel Pin
Locates in Bottom Hole
of P& Q
Threaded Insert
will receive D

CCH01788:08/004
To relocate Crib Spring, Remove
Hexhead Machine Screws BB
BB
B
then move Tabs to desired height.
Locate Tabs on Spring Rand rotate Tabs upward. Position the four
Tabs on Spring Rto the desired height allowed by the threaded holes
located on the 4-Position Spring Brackets G. Install a Hexhead Machine
Screw Bthrough each Spring Tab and into the selected threaded re-
ceiving hole on Spring Bracket G. Tighten Screws Bwith a 3/8
(10mm) wrench. Follow the same procedure when changing spring
heights at a later date. Periodically check Hexhead Machine Screws B
and tighten if needed.
STEP 5 - DIAGRAM 4: SPRING INSTALLATION
Holes to
receive
Phillips
Head
Machine
Screws
Ffor
attachment
to ends
P& Q.
DIRECTIONS FOR CONVERTING CRIB TO ATODDLER BED
When use as a crib has been completed, you have the option to convert to
a Toddler Bed for years of additional use in your childs room. Refer to Step
4 - Diagram 3. Remove Front Side Mand Foot Top Dowel T. Install Crib
Stretcher Sas shown in Sketch A. Dowel on Stretcher Slocates in top
hole at bottom of Foot Post P& Q, then secure with K-D Bolt E and K-
D Bolt Plug Cshown installed. Install Insert Nut Jand Allenhead Bolt Iin
holes near top of Foot Post P& Qas shown. Tighten Allenhead Bolt I
with Allen Wrench Aand Insert Nut Jwith Allen Wrench H. Spring
RR
RR
Rmust be installed in lowest position. Store the removed parts and
hardware in the event you wish to convert your Toddler Bed back to a crib.
Sketch A
(style may vary)
FMAINTENANCE OF YOUR CHILD CRAFT CRIB/TODDLER BED/FULL SIZE HEADBOARD & FOOTBOARD: Upon completion of assembly be sure all
screws, bolts and fastening devices have been tightened securely. A frequent check should be made of all screws, bolts and fastening devices and
tightened if needed. Before each usage or assembly, inspect crib for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use crib
if parts are missing or broken. Contact your Dealer or Child Craft [phone], for a replacement part or instructional literature if needed. Include Model
Identification Number with your request which you recorded on page 2 of these instructions. DO NOT SUBSTITUTE PARTS. DO NOT MAKE ANY
ALTERATIONS NOT DESCRIBED IN THESE ASSEMBLY DIRECTIONS.
FCLEANING INSTRUCTIONS FOR YOUR CHILD CRAFT CRIB/TODDLER BED/FULL SIZE HEADBOARD & FOOTBOARD: Mix together a mild solution
of gentle dishwashing liquid and water, apply to surface using a soft clean cloth lightly dampened in the solution. Rinse with clear water again using a
soft clean cloth, then dry all surfaces thoroughly with a soft dry cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL, OR COARSE RAGS
SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
FSTORAGE AND USE OF YOUR CHILD CRAFT CRIB/TODDLER BED/FULL SIZE HEADBOARD & FOOTBOARD: A printed plastic pouch is attached to
the crib spring for the permanent storage of the assembly directions. After completing the assembly process you are advised to read and be aware of
all WARNINGS, CAUTIONS, CLEANING, STORAGE, USE AND MAINTENANCE notices contained in this set of directions and printed on the plastic pouch
located on the underneath side of the crib spring. You will then place the complete set of assembly directions into the plastic pouch for future referral
by opening storage drawer. We caution you not to place excess hadrware in the plastic pouch as it could present danger to a child if retrieved. When
storing crib use CAUTION as extreme temperature or humidity changes could be harmful. Use CAUTION when a vaporizer is in use, always aim vapor
stream away from crib as well as away from any wood furniture item.
DIRECTIONS FOR CONVERSION TO A
FULL SIZE HEADBOARD & FOOTBOARD
Disassemble crib by removing Spring
R, Headboard Nand Footboard O
from Foot Posts P & Q, and Station-
Sketch B
(style may vary)
Spring R must be installed
in lowest position.
ary Side L. You have the option to remove the 4-Position Spring Brackets Gfrom the
Footboard Posts P& Qif you desire, but do not remove the factory installed brackets
GG
GG
G on the Stationary Side
LL
LL
L or any other items attached with wood screws.Attach
the Stationary Side and the Footboard Assembly to a Hook-End style full size bed frame
(model 6444) at the desired height. The Hooks on the bed frame locate over the factory
installed pins located in the slots in the Headboard and Footboard Assembly. Insert the Hole
Button Covers Kas shown.
NOTE: When using as a Toddler Bed the
mattress must have minimum dimensions
of 51-5/8 in. (1310mm) in length and 27-1/4
in. (690mm) in width and 4 in. (100mm) in
thickness but not to excees 6 in.
It is very important that the Stretcher SS
SS
S
is used when converting to a Toddler Bed.
Failure to install this part could result in
serious injury or death.
When using as a Toddler bed, the mini-
mum age shall not be less than 15 months
and the maximum weight shall not be
greater than 50 lb (22.7 kg).
WARNING
4-Position
holes to
receive
Hexhead
Machine
Screws B
to be
placed in
selected
height
position
hole for
Spring R
positioning
Ta b
Top surface
R
CLOSE UP VIEW
Ta b
B
G
GI
J
I
SE
K
s
K
L
P
T
Q
M
!

WARNING
FFAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY IN-
STRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
FREAD ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP
INSTRUCTIONS FOR FUTURE USE. A PLASTIC POUCH IS ATTACHED TO
CRIB FOR PERMANENT STORAGE OF THE INSTRUCTIONAL LITERATURE.
FBEFORE EACH USAGE OR ASSEMBLY, INSPECT CRIB FOR
DAMAGED HARDWARE, LOOSE JOINTS, MISSING PARTS OR
SHARP EDGES. DO NOT USE CRIB IF ANY PARTS ARE MISSING
OR BROKEN. ASK YOUR DEALER OR WRITE TO CHILD CRAFT,
P.O. BOX 444, SALEM, IN 47167-0444 USA (812)-883-3111) FOR RE-
PLACEMENT PARTS AND INSTRUCTIONAL LITERATURE IF
NEEDED. INCLUDE MODEL IDENTIFICATION NUMBERS WITH YOUR REQUEST WHICH
YOU RECORDED ON PAGE TWO. DO NOT SUBSTITUTE PARTS.
FAFTER RAISING SIDE, MAKE SURE LATCHES ARE SECURE. IF
YOUR UNIT HAS A DROP SIDE.
FWHEN CHILD IS ABLE TO CLIMB OUT OR REACHES THE
HEIGHT OF 35 INCHES (90 CENTIMETERS) THE CRIB SHALL NO
LONGER BE USED.
FDO NOT PLACE CRIB NEAR WINDOW WHERE CORDS FROM
BLINDS OR DRAPES MAY STRANGLE A CHILD.
FIF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR
CHILDRENS PRODUCTS.
FDO NOT LEAVE CHILD IN CRIB WITH SIDE LOWERED. BE SURE
SIDE IS IN RAISED AND LOCKED POSITION WHENEVER CHILD
IS IN CRIB.
FWHEN CHILD IS ABLE TO PULL TO STANDING POSITION, SET
MATTRESS TO LOWEST POSITION AND REMOVE BUMPER PADS,
LARGE TOYS AND OTHER OBJECTS THAT COULD SERVE AS
STEPS FOR CLIMBING OUT.
FNEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC
FILM AS MATTRESS COVERS BECAUSE THEY CAN CAUSE SUF-
FOCATION.
FDO NOT USE A WATER MATTRESS WITH THIS CRIB.
FREPLACE TEETHING RAIL(S) IF DAMAGED OR LOOSE. (IF
EQUIPPED WITH TEETHING RAILS.)
FSTRINGS CAN CAUSE STRANGULATION! DO NOT PLACE
ITEMS WITH A STRING AROUND A CHILDS NECK, SUCH AS
HOOD STRINGS OR PACIFIER CORDS. DO NOT SUSPEND
STRINGS OVER A CRIB OR ATTACH STRINGS TO TOYS.
FREMOVE ALL CRIB TOYS WHICH ARE STRUNG ACROSS CRIB
AREA WHEN YOUR CHILD IS BEGINNING TO PUSH UP ON HANDS
AND KNEES OR IS 5 MONTHS OF AGE, WHICHEVER OCCURS
EARLIEST. THESE TOYS CAN CAUSE STRANGULATION.
FWHEN DISASSEMBLING THIS CRIB, DO NOT REMOVE ANY ITEM
ATTACHED WITH WOOD SCREWS.
FALWAYS ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY
CHECKING REGULARLY, BEFORE PLACING THE CHILD IN THE
CRIB, THAT EVERY COMPONENT IS PROPERLY AND SECURELY
IN PLACE.
CCH01788:08/00 5
CAUTION
FANY MATTRESS USED IN
THIS CRIB MUST BE AT
LEAST 27-1/4 INCHES (69
CENTIMETERS), BY 51-5/8
INCHES (131 CENTIME-
TERS), WITH A THICKNESS
NOT EXCEEDING 6 INCHES
(15 CENTIMETERS). THE
DIMENTIONS OF THE MATTRESS
SHALL BE TAKEN FROM SEAM TO
SEAM OR EDGE TO EDGE WHERE AP-
PROPRIATE.
FUPON COMPLETION OF
ASSEMBLY BE SURE ALL
SCREWS, BOLTS AND FAS-
TENING DEVICES HAVE
BEEN TIGHTENED SE-
CURELY. A FREQUENT
CHECK SHOULD BE MADE
OF ALL SCREWS, BOLTS
AND FASTENING DEVICES
AND TIGHTEN IF NEEDED.
CHILD CRAFT
INDUSTRIES, INC.
P.O. BOX 444
SALEM, IN 47167-0444 USA
PH:812-883-3111
FAX:[phone]
http://www.childcraftind.com
CCH01788:08/00
JCHE.p65
MADE IN USA
s
!