Child Craft Crib'n'Double Bed 34801 Firmware update

H04755:11/08 1
A B
C
(8) Allenhead Bolts
(2) Allenhead Bolts
(1) Allen Wrench
G
(1) Allen Wrench
(8) Allenhead Bolts
(1) Crib Stretcher
(for use on Toddler Bed only)
(1) Stationary Post Left
(1) Stationary Post Right
(1) Foot Post Left
Division of Foundations® Worldwide, Inc.
• 7001 Wooster Pike, Medina, OH 44256 USA • PH: 1 877.716.2757 (U.S. Only) or +1 330.722.5033 • FAX: [phone]
• www.childcraft-furniture.com / www.foundations.com
Directions for Maintenance, Cleaning, Storage and Use of your Crib/Toddler Bed are also included.
BEFORE STARTING THE ASSEMBLY PROCEDURE, READ ALL DIRECTIONS WITH CARE.
YOU WILL NEED THE FOLLOWING FOR THE ASSEMBLY OF YOUR CRIB/TODDLER BED:
3Flat Tipped Screwdriver 3enclosed Allen Wrenches (A&B)
Crib‘N’Double beD CoNverts
to toDDler beD or Full size
HeaDboarD & FootboarD
34801
assembly DireCtioNs aND Parts list
Parts eNCloseD iN HarDware bag (noted when shown actual size)
H
Parts eNCloseD iN CartoN
K L M
I
(1) Foot Post Right
(8) K-D Nuts
NOTE: Do not discard extra parts. Parts D, E, G, I and J will be needed to later ll empty holes, convert to a toddler
bed and to attach bed rails to the headboard and footboard. See pages 5, 6 and 7.
N
(1) Long Foot Assembly
(1) Crib Spring
Pouch S
P
(1) Stationary Side
Q
(16) Allenhead Bolts
F
(8) Allenhead Bolts
J
InsIde face InsIde face InsIde face InsIde face
(1) Short Foot Assembly
(1) Short Head Assembly
O
R
T
sI291f
D
(8) K-D Nuts
E(18) Insert Nuts
(8) Allenhead Bolts
F

H04755:11/082
Carefully remove and lay out all hardware and parts. Check quantities and match the Hardware List and the Parts List. NOTE: During
the assembly process whenever using screws or bolts, check each with the Hardware List by letter and size identication. Place
each screw or bolt on the diagram of the item which is sketched actual size. Be sure to use the proper size specied in the
assembly directions. If any parts are missing or broken or you need assistance with assembly, DO NOT return the product to your
dealer. Call Foundations® for assistance at 1 877.716.2757 (U.S. Only) or +1 330.722.5033 (Monday through Friday, 9:00 a.m.– 4:00 p.m.
Eastern Time). Please have the Crib’n’Double Bed by the model identication number stamped on the inside face or bottom edge of the
Headboard, Footboard or crib sides, available when you call or write us at: Foundations®, 7001 Wooster Pike, Medina, OH 44256 USA.
Make note of all identication numbers and include this information with your request. DO NOT SUBSTITUTE PARTS! Record your model
identication number here for future identication: Model #________________________
PreParatioN
Attach Stationary Posts K & L to Stationary Side Q by inserting K-D Nuts C into their locator holes in the underside of the bottom rail and
top rail of Stationary Side Q, then insert Allenhead Bolts F through their locator holes in Posts K & L. Thread Allenhead Bolts F into K-D
Nuts C but leave slightly loose until both posts are attached. Tighten all Allenhead Bolts F securely using Allen Wrench A.
Insert Allenhead Bolts J into their locator holes in the back of Stationary Post K & L and Insert Nuts E into their locator holes in the front
of Stationary Post K & L. Tighten securely using Allen Wrench A with Allenhead Bolts J and Allen Wrench B with Insert Nuts E.
steP 1 - Diagram 1: assemble statioNary siDe
NOTE: Tighten securely means a good
snug t, do not allow the heads of bolts
and screws to dig into the wood.
Q
C
F
F
E
C
J
K
L
E
C
J
C
NOTE: The locator holes for Allenhead Bolts J and Insert Nuts
E face the outside edge of the crib when Stationary Post Left K
and Stationary Post Right L are installed properly.
NOTE: Install dowel in each
end of bottom rail into hole
located in posts K and L.

H04755:11/08 3
F
C
R
C
C
E
C
E
J
N
F
J
M
steP 2 - Diagram 2: assemble loNg Foot assembly
steP 3 - Diagram 3: attaCH Foot/HeaD assembly to statioNary siDe aND loNg Foot assembly
Insert Allenhead Bolts H through their locator holes in Foot/Head Assemblies O & P and thread into the threaded inserts in Stationary Posts
K & L. To attach the Long Foot Assembly, Insert Allenhead Bolts H through their locator holes in Foot/Head Assemblies O & P and thread
Attach Foot Posts M & N to Long Foot Assembly R by inserting K-D Nuts C into their locator holes in the
underside of the bottom rail and top rail of Long Foot Assembly R, then insert Allenhead Bolts F through
their locator holes in Posts M & N. Thread Allenhead Bolts F into K-D Nuts C but leave slightly loose
until both posts are attached. Tighten all Allenhead Bolts F securely using Allen Wrench A.
Insert Allenhead Bolts J into their
locator holes in the front of Foot
Posts M & N and Insert Nuts E
into their locator holes in the back
of Foot Posts M & N. Tighten
securely using Allen Wrench A
with Allenhead Bolts J and
Allen Wrench B with Insert
Nuts E.
NOTE: Only (6) Allenhead Bolts H
are visible in this drawing. Install a
total of (8) Allenhead Bolts H.
into the threaded inserts in Foot
Posts M & N. Tighten Allenhead
Bolts H securely with Allen Wrench
A. Do not overtighten. Be careful
not to allow the heads of Allenhead
Bolts H to dig into the wood.
threaded Insert
H
H
threaded Insert
threaded Insert
K
L
O
M
N
R
Q
NOTE: dUrInG asseMBLY
Of POsts M & n tO the LOnG
fOOt asseMBLY r, It Is
IMPOrtant tO hOLd
the tOP caP fLUsh
WIth the POsts.
TOP CAN ON
LONG FOOT ASSEMBLY
FLUSH
POSTS M & N
NOTE: Install
dowel in each end
of bottom rail into
hole located in
posts M and N.
P
NOTE: WARNING label
will be visible here and
also on outside of part O.

H04755:11/084
steP 4 - Diagram 4: attaCH sPriNg
“sWInG arMs”
seleCt oNe oF two HeigHts
S
NOTE: Crib siDes aND Posts
were omitteD From Diagrams
For Clarity.
O
Before installing Spring S, determine the height for installation. Pull out “Swing Arms” to the approximate angle as shown. With the help of
a friend, carefully lower Spring S into the assembled crib to the predetermined height. Insert Allenhead Bolts J into the locator holes in the
S
O
E
J
“Swing Arms” and through the locator holes in Head/Foot Assembly O & P. From the outside of the assembled crib, insert Bronze
Insert Nuts E into their locator holes and thread onto Allenhead Bolts J. Tighten securely using Allen Wrench A with Bolts J and
Allen Wrench B with Bronze Insert Nuts E. Also install Allenhead Bolts J and Bronze
Insert Nuts E in the spring height locator holes not used at this time. Before installing
mattress, see mattress size requirements under CAUTION on page 8 and MAINTENANCE
WIth PrOdUct
stIckers
assembleD Crib
Q
Mattress sold separately. See mattress size
requirements under CAUTION on page 7.
E
J
F
F
E
K
F
J
F
M
H
R
N
P
O
J
S
H
L
J
Visible hardware and crib parts are identied.
section on page 8. Also review WARNINGS on
page 9.

H04755:11/08 5
When use as a crib has been completed, you have the option to convert to a Toddler Bed for years of additional use in your child’s room.
Remove mattress. Spring S must be installed in lowest position. Refer to steP 2 - Diagram 2 and remove and store (see Storage on
page 7) Long Foot Assembly R by removing Allenhead Bolts F and K-D Nuts C. Stretch Foot Posts M and N just enough to allow the
wood dowels on Crib Stretcher T to t into their locator holes in Foot Posts M and N. Use Allenhead Bolts F and K-D Nuts C you removed
from Long Foot Assembly R to attach Crib Stretcher T to Foot Posts M and N as shown. Tighten securely using Allen Wrench A.
Fill the empty holes in the top of Foot Posts M and N by inserting Allenhead Bolts I through their locator holes and thread into Insert Nuts
E. Tighten securely using Allen Wrench A for Allenhead Bolts I and use Allen Wrench B for Insert Nuts E. Store the removed parts and
hardware in the event you wish to convert your Toddler Bed back to a crib. Do not store extra hardware in pouch.
steP 5 - Diagram 5: CoNvert “Crib” to a “toDDler beD”
F
N
F
C
C
T
M
I
E
E
I

H04755:11/086
WARNING (For Toddler Bed)

!
• Infants have died in toddler beds from entrapment and strangulation. Failure
to follow these warnings and the assembly instructions could result in serious
injury or death.
• NEVER use bed with children under 15 months.
• NEVER place bed near windows where cords from blinds or drapes may strangle
a child.
• DO NOT place items with a string, cord, or ribbon around a child’s neck, such as
hood strings or pacier cords.
• DO NOT suspend strings over a toddler bed for any reason.
• The users maximum weight shall not be greater than 50 lbs. (22.7 kg).
• The mattress intended for use on the bed shall be a full-size crib mattress having
minimum dimensions of 51-5/8 in. (1310 mm) in length and 27-1/4 in. (690 mm) in
width and 4 in. (100 min) in thickness, but not to exceed 6 in. (150 mm).
• Mattress MUST be moved into lowest position for proper positioning behind
stretcher. It is very important that Stretcher T is used to prevent the mattress from
moving and creating a gap between the mattress and the bed which could result
in entrapment of the child. Failure to install this part could result in serious injury
or death.
• This crib contains all components necessary to convert to a toddler bed. However,
a guardrail may be available for purchase to provide additional security. Contact
Foundations® for assistance. Refer to maintenance section for contact information.

H04755:11/08 7
Disassemble crib by removing mattress and Spring S, Foot/Head
Assemblies O & P from Stationary Posts K & L, and Foot Posts
M & N. Attach the Stationary Side Assembly and the Long Foot
Assembly to bed rail model #6454 (purchased separately) using
Allenhead Bolts G and K-D Nuts D. Fill the exposed locator holes
(threaded inserts) in all four posts with Allenhead Bolts J as shown
below.
CoNvert From Crib to a
“Full size HeaDboarD & FootboarD”
CoNvert From toDDler beD to a
“Full size HeaDboarD & FootboarD”
reMOve
reMOve
Disassemble toddler bed by removing mattress and Spring S, Foot/
Head Assemblies O & P, Stretcher T, Foot Posts M & N. Refer
to steP 2-Diagram 2 and attach Foot Posts M & N to Long Foot
Assembly Q. Attach the Stationary Side Assembly and the Long
Foot Assembly to bed rail model #6454 (purchased separately)
using Allenhead Bolts G and K-D Nuts D. Fill the exposed locator
holes (threaded inserts) in all four posts with Allenhead Bolts J as
shown below.
reMOve
reMOve
reMOve
reMOve
E & J
reMOve
E & J
reMOve
E & J
J
fULL sIze
headBOard asseMBLY
fULL sIze
fOOtBOard asseMBLY
L
K
M
N
R
Q
J
Lower threaded inserts do
not need to be filled with
Allenhead Bolts J.
Lower threaded inserts do
not need to be filled with
Allenhead Bolts J.
Fill empty holes at the top of
Stationary Posts K & L and
Foot Posts M & N with
Allenhead Bolts J as shown.

H04755:11/088
MAINTENANCE OF YOUR CRIB/TODDLER BED/FULL SIZE HEADBOARD & FOOTBOARD: Upon completion of the assembly, check
to ensure that all screws, bolts and fastening devices have been tightened securely. There should be a frequent check of this product for
damaged hardware, loose joints, missing parts or sharp edges before and after assembly and frequently during use. DO NOT use crib if
any parts are missing or broken. If any parts are missing or broken or you need assistance with assembly, DO NOT return the product to
your dealer. Call Foundations® for assistance at 1 877.716.2757 (U.S. Only) or +1 330.722.5033 (Monday through Friday, 9:00 a.m.– 4:00
p.m. Eastern Time) for replacement parts and instructional literature if needed. Include model identication numbers which you recorded
on page 2. DO NOT substitute parts.
CLEANING INSTRUCTIONS FOR YOUR CRIB/TODDLER BED/FULL SIZE HEADBOARD & FOOTBOARD: Mix together a mild
solution of gentle dishwashing liquid and water, apply to surface using a soft clean cloth lightly dampened in the solution. Rinse with clear
water again using a soft clean cloth, then dry all surfaces thoroughly with a soft dry cloth. NO ABRASIVE CLEANERS, SCOURING PADS,
STEEL WOOL, OR COARSE RAGS SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
STORAGE AND USE OF YOUR CRIB/TODDLER BED/FULL SIZE HEADBOARD & FOOTBOARD: A printed pouch is attached to
the crib spring for the permanent storage of the assembly directions. After completing the assembly process you are advised to read and
be aware of all WARNINGS, CAUTIONS, CLEANING, STORAGE, USE AND MAINTENANCE notices contained in this set of directions
and printed on the pouch located on the crib spring. You will then place the complete set of assembly directions into the pouch for future
referral. We caution you not to place excess hardware in the pouch as it could present danger to a child if retrieved. When storing crib use
CAUTION as extreme temperature or humidity changes could be harmful. Use CAUTION when a vaporizer is in use, always aim vapor
stream away from crib as well as away from any wood furniture item.
CAUTION
•ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 INCHES (69 CENTIMETERS),
BY 51-5/8 INCHES (131 CENTIMETERS), WITH A THICKNESS NOT EXCEEDING 6 INCHES
(15 CENTIMETERS).
THE DIMENSIONS OF THE MATTRESS SHALL BE TAKEN FROM SEAM TO SEAM OR EDGE TO EDGE WHERE APPROPRIATE.
•UPON COMPLETION OF ASSEMBLY BE SURE ALL SCREWS, BOLTS AND FASTENING DEVICES
HAVE BEEN TIGHTENED SECURELY. A FREQUENT CHECK SHOULD BE MADE OF ALL SCREWS,
BOLTS AND FASTENING DEVICES AND TIGHTEN IF NEEDED.
CRIB TODDLER BED FULL SIZE
HEADBOARD AND FOOTBOARD

H04755:11/08 9
Division of Foundations Worldwide, Inc.
7001 Wooster Pike
Medina, OH 44256 USA
Telephone: [phone] (U.S. Only)
or +1 330.722.5033
Fax: [phone]
www.childcraft-furniture.com
www.foundations.com
WARNING
• FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH.
WARNING: Infants can suffocate on soft bedding. NEVER add a pillow
or comforter. NEVER place additional padding under an infant.
• Read all instructions before assembling crib. Keep instructions for future use. A pouch is
attached to crib for permanent storage of the instructional literature.
• Infants can suffocate in gaps between crib sides and a mattress that is too small.
• To reduce the risk of SIDS pediatricians recommend healthy infants be placed on their backs
to sleep, unless otherwise advised by your physician.
• To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or
clothing on loose fasteners.
• After raising side, make sure latches are secure (if your unit has a drop side).
• When child is able to climb out or reaches the height of 35 inches (90 centimeters) the crib
shall no longer be used.
• DO NOT place crib near window where cords from blinds or drapes may strangle a child.
• If renishing, use a non-toxic nish specied for children’s products.
• DO NOT leave child in crib with side lowered. Be sure side is in raised and locked position
whenever child is in crib.
• When child is able to pull to standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
• NEVER use plastic shipping bags or other plastic lm as mattress covers because they can
cause suffocation.
• DO NOT use a water mattress with this crib.
• Replace teething rail(s) if damaged, cracked, or loose (if equipped with teething rails).
• Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such
as hood strings or pacier cords. DO NOT suspend strings over a crib or attach strings to toys.
• When disassembling this crib, DO NOT remove any item attached with wood screws.
• Always ensure a safe environment for the child by checking regularly, before placing the child
in the crib, that every component is properly and securely in place.
• Check this product for damaged hardware, loose joints, missing parts or sharp edges before and
after assembly and frequently during use. DO NOT use crib if any parts are missing, damaged or
broken. If any parts are missing or broken or you need assistance with assembly, DO NOT return
the product to your dealer. Call Foundations® for assistance at 1 877.716.2757 (U.S. Only) or +1
330.722.5033 (Monday through Friday, 9:00 a.m.– 4:00 p.m. Eastern Time) for replacement parts
and instructional literature if needed. Include model identication numbers with your request
which you recorded on page 2. DO NOT substitute parts.
• Follow warnings on all products in a crib.
!

!