Chileaf CL830 User manual

1
ARMBAND HEART RATE MONITOR
USER MANUAL
CL830

3
Thank you for purchasing our ANT+ & BLE heart rate armband, this product transmits the real-time heart
rate data through Bluetooth or ANT+ to heart rate receiving device, sports and health App, helping you to
keep it for reference.
!!WARNING!!
This is not a medical device and is intended for training and recreational use only. Consult a physician prior
to determine appropriate heart rate zones.

4
NOTICE
Our armband heart monitor is waterproof to IEC Standard 60529 IP67. It can withstand immersion in 1 meter
of water for 30 minutes. Prolonged submersion can cause damage to the unit.
a. Heart rate monitor armband
b. charging cable
d. User manual
Basic Parameters
Product size: 46.5x29x11.5mm
Weight: 13g (device without strap or accessories)
Water resistance: IP67
Working temperature: -10°C to +50°C/14°F to 122°F
Transmission: ANT+, BLE

5
Using the Armband Monitor
Turn-on: Press the start-up button, the purple led will blink slowly to indicate
heart rate work properly, otherwise purple led will blink quickly. If pair with smart
device successfully, the blue led will blink slowly.

6
Turn-off:
times to enter shutdown mode.
Charging:
Charge the Armband Heart Rate Monitor for 1.5 hours or until a solid green
light indicates the unit is fully charged.
a. Ifthe red LED is on whenever starting up or during of operation, it indicates
the battery is on low level and need to charge.
CHARGING
TERMINALS
HEART RATE SENSOR
ARMBAND CHARGING CABLE
!!Remove
Protective
Sticker!!

7
continuously;
Alert:
1. The unit will alert in vibration once heart rate change 8 times in 1 sec if the heart rate range is 120~150.
2. The unit will alert in vibration once heart rate change 5 times in 1 sec if the heart rate range is 150-180.
3. The unit will alert in vibration once heart rate change 3 times in 1 sec if heart rate is more than 180.

8
Wearing:
Wear armband on the upper portion of the forearm. Sensor should be on the inside or top of forearm. It
should be worn snug enough not to move on your arm,
but NOT so tight that it restricts arm circulation.

9
Initial Setup with Bluetooth Smart Fitness Apps
1. Set Bluetooth on the device to ON.
2. Find the Sensor Settings menu in the Bluetooth Smart Fitness App.
3. Connect the device armband by turning it on.
Initial Setup with Bluetooth Smart devices (Sports Watches, Fitness Equipment & GYM Team Training System.)
1. From the device settings menu select “Add HR sensor”
2. Connect the device armband by turning it on.

10
Initial Setup with ANT+ devices (Sports Watches & Fitness Equipment)
Turn on the armband and move within range of your display device.
Note: Heart rate monitoring will work with most Bluetooth Smart Fitness Apps. Pedometer with other function
are only supported in the Chileaf APP and will also work with Apps which have integrated the SDK.
Compatible Apps
Wahoo Fitness, Polar Beat, Strava, Zwift, Runtastic Pro, Nike+ Run Club

11
Disclaimer
• The information contained in this manual just for reference. The product described above may be subject
to alteration owing to the manufacturer's continuing research and development plans, without making an
announcement in advance.
• We shall not bare any legal responsibility for any direct or indirect, accidental or special damages, losses
and expenses arising from or in connection with this manual or the contained product.

Version: V1.0
CE and FCC statement
Hereby, Chileaf, declares that Armband heart rate monitor(CL830) is in compliance with the essential
requirements and other relevant provisions of Directive RED 2014/53/EU. A copy of the signed and dated
Declaration of Conformity is available.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.