CHINON SPLASH Setup guide

CHINON SPLASH
On line manual
posted 12-8-'02
This manual can be used as a reference for many Chinon "Auto" cameras
If the images are too small, I may have larger, almost identical images, from the CE-4 camera page.
This is the full text and images from the manual.
This camera manual library is for reference and historical purposes, all rights reserved.
This page is copyright© by M. Butkus, N.J.
This page may not be sold or distributed without the expressed permission of the producer
I have no connection with Chinon Co., Japan
If you find this manual useful, how about a donation of $3 to:
M. Butkus, 29 Lake Ave., High Bridge, NJ 08829-1701
and send me your e-mail address so I can thank you.
Most other places would charge you $7.50 for a electronic copy
or $18.00 for a hard to read Xerox copy.
This will help me to continue to host this site, buy new manuals, and pay their shipping costs.
It'll make you feel better, won't it?
If you use Pay Pal, use the link below. Use the above address for a check, M.O. or cash.
Back to my main Camera manual page
www.PayPal.me/butkus

TABLE OF CONTENTS
Nomenclature . 2
Specifications 6
Simplified Guide for Using Your Camera 10
Installing the Batteries 12
Battery Testing 14
Automatic Film Speed Setting 16
Automatic Film Loading 16
Holding the Camera 22
Viewfinder 24
Waterproof Photography 26
Auto-Focus Shooting 30
Focus Lock System 34
Film Rewinding 36
Flash Photography 38
Attach Neckstrap 42
Care of the Camera 43
NOMENCLATURE
1. Strap eyelet
2. Film door closure
3. Shutter release
button
4. Autofocus window
5. Viewfinder
6. Flash
7. Fixed waterproof
and protective lens
cover
8. Lenswww.4.butkus.or g
9. Exposure metering
window
10. Power/Flash switch
lever

11 Waterproof seal
12. Film rewind
shaft
13. Frame counter
14. Viewfinder
eyepiece
15. Flash ready
indicator
16. Take-up spool
17. Back cover
18.Film pressure
plate
19. Film type
window
20. Battery cap
21. Film chamber
22. Automatic film
speed setting
contacts
23. Film guide
24.Tripod screw
25. Rewind switch
lever
26. Sprocket
27. Film tip mark
SPECIFICATIONS
TYPE: Weatherproof, dust and sand resistant, fully automatic 35 mm compact autofocus camera.
PICTURE FORMAT: 24x36 mm

LENS: 35 mm F3.9, 3 elements in 3 groups. VIEWFINDER: Albada type bright frame with AF frame,
parallax marks, AF lock indication LED (green) and under exposure warning/battery check LED (red).
SHUTTER: Programmed electronic shutter; 1/90 sec. - 1/410 sec., mechanical release, shutter locks when the
power/flash switch lever is in the OFF position.
EXPOSURE METER: Programmed EE, CdS.
EV RANGE: EV1O.5--EV14.5 (ISO 100).
AUTOMATIC FILM SPEED SETTING: The film speed is automatically set when using a OX-coded film of
ISO 100/21° - 1000/31°. Non-DX film will be set to ISO 100/21°.
FOCUSING: Infrared automatic focusing system with possible prefocus; cancellable. FOCUSING RANGE: 1
.3 meters (4.26 ft) to infinity.www.4.bu t kus.org
FILM LOADING: Auto loading system with built-in motor.
FILM WIND: Automatic power winder for single frame advance.
FILM REWIND: Automatic power rewinding; rewind actuated with rewind switch lever.
AUTO REWIND STOP: Film rewinding automatically stops upon completion.
EXPOSURE COUNTER: Indicates number of exposed frames and returns frame by frame while rewinding,
and resets to "S" when camera back is opened.
FLASH: Fixed type electronic flash, flashmatic, Guide number 10 (ISO 100 meters), Effective range of 1.3--
3.5 meters (4.26 - 11.48 ft) at ISO 100, Recycling time of approximately 5 seconds. Flash ready indicator built-
in.
WATER RESISTANCE: Washable with water.
OTHER FEATURES: Film type window, tripod screw and neck strap.
POWER SOURCE: Two 1.5, V "AA" size alkaline batteries (LR6). 4www.butkus.org
DIMENSIONS: 1 40(W)x 77(H) x 53(0) mm (5.51 x3.03"x2.09").
WEIGHT: 370 g (13.06 oz)

SIMPLIFIED GUIDE FOR USING YOUR
CAMERA
1. Installing Batteries (Fig. A)
2. Set the Power/Flash switch lever to the ON position
(Fig. B)
3. Automatic Film Loading (Release shutter 3 times)
(Fig. C)
4. Be Sure to Direct AF Frame at Your Subject (Fig. D)
5. Release the Shutter (Fig. E)
6. Automatic Film Rewind
(Fig. F)
7. Remove the Exposed Film
(Fig. G)

1. Put a small coin in the groove and turn it as illustrated to
open the Battery Cap (Fig. 1). Place two 1.5 V "AA" size
alkaline batteries (LR-6) into the battery compartment so
as to correspond with the positive (+) and negative (--)
marks shown inside (Fig. 2).
INSTALLING THE BATTERIES
NOTE:
* If you do not intend to use your
camera for a long period of time,
remove the batteries and store them in
a dry location. This will prevent the
possibility of battery leakage and
damage to your camera. Do not use Ni-
Cad batteries. Be sure to replace both
batteries at the same time when the
batteries are too weak to operate the
camera. When replacing the batteries,
make sure they are not wet. If so, wipe
it with cloth before use.ww w.4. but kus.org
BATTERY TESTING
1. Set the Power/Flash Switch
Lever to the ON position (Fig. 3)
2. Cover the exposure metering
window with your hand and press
the shutter release button halfway
(Fig. 4).
3. Make sure the under-exposure
warning LED (red) lights up (Fig.
5). If the red LED fails to
illuminate, the batteries are too
weak and need to be replaced.
NOTE: * When the Power/Flash
Switch Lever is in the OFF
position the shutter will be
blocked. As temperature
decreases, especially below 0°C
(32°F) battery performance
declines. Keep batteries warmed
under these conditions.

AUTOMATIC FILM SPEED SETTING
The film speed is automatically set when using a DX-coded film of
ISO 100/21° - 1000/31 Non-DX films will be set to ISO 100/21° (Fig. 6).
AUTOMATIC FILM LOADING
Always load and unload your camera in subdued light, and never in
direct sunlight.
1. Slide the film door closure latch in the direction of the arrow and lift
up the closure as illustrated to open the back cover (Fig. 7).www.4.but kus.org

2. Insert a film cartridge into the film chamber (Fig. 8).
3. Align the trimmed end of the film on the take-up spool with the
yellow film tip mark. When loading film, make sure that the film
lies flat between the film guides. Engage the perforation of the film
with the teeth of the sprocket (Fig. 9). Close the back cover as
illustrated (Fig. 10).

4. Set to the Power/Flash Switch Lever to ON position and release the
shutter button three times until the figure 1" appears in the frame
counter (Fig. 11). The camera is now properly loaded.
NOTE:
* If the film counter does not function, the film is not properly
advancing. Open the back cover and re-load the camera. When
inserting film cartridge, make sure they are not wet. If so, wipe it with
cloth before use.
4. Cartridge Window
This camera is equipped with a convenient
Cartridge Window so that you can check what
type of film is in use (Fig. 12).

HOLDING THE CAMERA
Hold the camera firmly in both hands with at least
one elbow at your side to ensure camera
steadiness when taking a picture.
VIEWFINDER
(1) Bright line frame
(2) Parallax marks
(3) Auto-focus frame
(4) AF indication LED (green)
(5) Under exposure warning! Battery check LED
(red)

WATER PROOF PHOTOGRAPHY
Your SPLASH AF camera is designed to be water-
resistant. It can safely be washed with water. You can
use it anywhere, even on a rainy day or at the beach. Do
not intend to use it under water.
Check Waterproof Seal
1. Make sure the waterproof
rubber seal inside is not partly or wholly
removed.
2. Make sure there is no sand or foreign
material on or around the waterproof seal.
NOTE:
* When replacing batteries and/ or
inserting a film cartridge, make sure that
they are not wet. If so, wipe with cloth
before use.
When the lens cover or autofocus
window is covered with waterdrops or
dirt, wipe them clean with a soft cloth
before taking a picture.

AUTO-FOCUS SHOOTING
1. Look through the viewfinder and
compose the picture so that the main
subject is placed in the auto focus frame
(3). 2. Gently press the shutter release
button halfway. The camera
automatically focuses and the AF signal
(green) will light.
3. When taking a picture closer than 1.5
meters (5 feet), the image area is
indicated by the two parallax marks (2
) in
the top left and top right corners of the
viewfinder. Compose the photograph
within the imaginary zone extending
from the corner of the parallax marks
(Fig. 13).
NOTE: When a subject is positioned
closer than 1.3 meters (4.26 feet), the
pictures will not be in focus.
4. Press the shutter release button all the way. If the underexposure
warning LED (5) lights up, use the built-in flash (Fig. 14).
See FLASH PHOTOGRAPHY.
NOTE:
The following subjects will not be properly auto-focused:
* Shiny subjects such as water surfaces or the exterior of a car body.
* Subjects viewed through a glass window. Semi-
reflective subjects.

FOCUS LOCK SYSTEM
This feature may be used to eliminate tricky focusing situations
such as when the main subject is located "off center" in the
viewfinder. In such a situation, first focus on the main subject (by
placing the subject in the AF frame) and partially depress the
shutter release button. Hold the shutter release button in the
halfway position and recompose the subjects in the viewfinder and
fully depress the shutter release button to take the picture (Fi
g. 15).
This focus lock feature can be cancelled by removing your finger
from the release button.
NOTE:
When auto rewinding takes a long time to complete,
replace the batteries with a fresh set.
FILM REWIND
When the film in the camera is fully
exposed, the motor stops and shutter
release is blocked. Start rewinding at
once.
1. Slide the Rewind Switch Lever
in the direction of the arrow to rewind the
film (Fig. 16). 2. During rewinding, the
frame number counts backward showing
how many frames are still remaining to be
rewound. When rewinding is over, "S"
appears in the frame counter and
rewinding is automatically stopped (Fig.
17). Open the back cover and remove the
film.

FLASH PHOTOGRAPHY
Switch to flash photography if the
under-exposure warning LED lights up
while pressing the shutter release button
halfway (Fig. 18).
1. Set the Power/Flash Switch Lever to
the position to turn on the flash.
2. Make sure that the Flash Ready
Indicator is illuminated before taking a
picture (Fig. 19).
3. When the flash is no longer required,
be sure to slide back the lever to the ON
or OFF position (Fig. 20).
Daylight Flash Photography
If the main subject has less light falling
on it than the surrounding area and
background, underexposure of the main
subject will result. If such situations, use
the flash even in daylight.
NOTE:
* If you release the shutter
before the Flash Ready Indicator glows,
the exposure will not be correct.

ATTACH NECK STRAP
CARE OF THE CAMERA
Your camera is a precision instrument. When used with care it will provide years of trouble-
free service. Protect
your camera from dirt, rain, dampness and excessive heat. Avoid touching the lens. To clean the lens, wipe it
gently with a soft lintless cloth or tissue. Do not use eyeglass tissues as they might damage the lens coating. Do
not disassemble and touch the inside of the camera as possible high voltage in the flash circuitry can be
dangerous.
Because we continually strive to improve our products, we may change specifications without prior notice.