Amico BARCDHLD2-LCD Guide
Installation Tools
Medical Facility Responsibility
Mounting onto LCD VESA Plate
It is the responsibility of the end user to ensure all aspects of the installation are covered by following the
full manual at: http://www.amico.com/barcode-dock-mount
Installation and Adjustment Instructions
Barcode Dock Mount
Quick Setup for BARCDHLD2-LCD
!
WARNING
No. 2 Phillips head screwdriver (not provided)
1/8" HEX key for BARCDHLD2-M (not provided)
7/16" wrench for BARCDHLD2-LCD conguration (not provided)
1. For BARCDHLD2-LCD, slide X-MON-SHELF-ARM to desired position and tighten two H-HNUT-1420. Insert and tighten two H-1420-LNUT-NYL to
lock X-MON-SHELF-ARM in place as seen in Figure 1.
2. Loosely insert 2X H-PHMS-M4-12 through the top two holes of X-MON-HDL-BDY and into the monitor (not provided) as seen in Figure 2.
3. Slide two H-PHMS-M4-12 into the U-notches on LCD VESA plate (not provided). Insert another two H-PHMS-M4-12 into the two bottom holes of
LCD VESA plate, X-MON-HDL-BDY, and into monitor as seen in Figure 3.
4. Tighten four H-PHMS-M4-12 in a cross-pattern.
Figure 1
Figure 2
Figure 3
Tools
1/8" HEX key No. 2 Phillips screwdriver
Adjustable wrench
* Tools not provided by Amico
Amico Accessories Inc. 85 Fulton Way, Richmond Hill, ON L4B 2N4, Canada
Toll Free Tel: 1.877.264.2697 | Tel: 905.763.7778 | Fax: 905.763.8587
www.amico.com
Mounting of Devices
Installation and Adjustment Instructions
Barcode Dock Mount
AAIMBARCDHLDLCDQUICK 09.18.2014
Quick Setup for BARCDHLD2-LCD
FIGURE 8
FIGURE 9
FIGURE 10
FIGURE 11
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
DATE:
DATE:
PROJECTION
www.amico.com
1. For the BARCDHLD2-LCD:
Determine the mounting pattern on the barcode scanner base to be mounted. If the barcode scanner base is too large to mount onto
X-BRCDHLD-LBKT, proceed to step 2 for the installation of the secondary plate.
2. If the secondary plate X-BRCDHLD-PLT is required, determine the preferred orientation and secure by inserting two or three H-FHMS-832-12
through X-BRCDHLD-PLT, X-BRCDHLD-LBKT, two or three H-WLM-08, two or three H-ACNUT-8-32 ensuring that the mounting screws do not
interfere with the mounting pattern of the barcode scanner base.
NOTE: Please use two or three points to attach the secondary plate depending on what will get you the most secure connection without
interfering with the product on the mounting platform.
FIGURE 8
FIGURE 9
FIGURE 10
FIGURE 11
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
DATE:
DATE:
PROJECTION
www.amico.com
FIGURE 8
FIGURE 9
FIGURE 10
FIGURE 11
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
DATE:
DATE:
PROJECTION
www.amico.com
FIGURE 8
FIGURE 9
FIGURE 10
FIGURE 11
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
DATE:
DATE:
PROJECTION
www.amico.com
Adjustment Procedure
1. To adjust BARCDHLD2-LCD, remove two H-CAP-14-W,
two H-1420-LNUT-NYL and loosen two H-HNUT-1420.
2. Slide X-MON-SHELF-ARM to desired location and re-tighten
two H-HNUT1420 and H-1420-LNUT-NYL.
Other Amico Rack & Stand manuals
Amico
Amico ARS User manual
Amico
Amico SSM Arm Guide
Amico
Amico BARCHLD2 Product manual
Amico
Amico Gooseneck User manual
Amico
Amico AHM Service manual
Amico
Amico HMA-VESA-SPK-PLT Technical specifications
Amico
Amico Falcon IT Guide
Amico
Amico RS-42-PKS Series Original operating instructions
Amico
Amico Falcon IT User manual
Amico
Amico VRS User manual
