Cisco TelePresence Touch 8 User manual

78-19948-02 | 2011 DECEMBER.
Copyright © 2010-2011 Cisco Systems, Inc. All rights reserved.
Cisco TelePresence Touch 8”
INSTALLATION GUIDE

— 2 —
This box contains:
• Cisco TelePresence Touch 8” with cable (7.5m / 25 ft)
• Power adapter
• Power cable (1.8 m / 6 ft) (included when Touch is shipped as a stand-alone unit)
• Shielded Ethernet cable (5m / 16ft)
• Cleaning cloth
Safety requirement
You have to use a shielded Ethernet cable (as supplied).
User documentation
User documentation for Cisco TelePresence products, including compliance and
safety information, is found on http://www.cisco.com/go/telepresence/docs.
A Class declaration
WARNING
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
A级声明 (A Class product declaration)
本产品为 A级ITE，在其使用说明，铭牌等显著位置中已包含如下内容的声明
(We declare here that the subject product is A class ITE product, and the
following statement is clearly marked in the user manual or nameplate):
声明所在位置 (Position of the Declaration): 使用说明 User Manual
铭牌 Nameplate
申请号 (Application No.)：
申请人 (Applicant):
型号 (Model Number)：
签字/盖章 Signature/Stamp:
日期 Date:
警告
此为 A级产品。在生活环境中，该产品可能会造成无线电干扰。在这种
情况下，可能需要用户对干扰采取切实可行的措施。
WARNING:
This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.

— 3 —
AConnecting the touch screen via LAN
1. Restart the codec before you proceed with the installation.
2. Connect the touch screen cable to the Power adapter.
3. Connect the shielded Ethernet cable between the Power adapter and the LAN
(Ethernet) socket.
4. Connect the supplied power cable between the Power adapter and the power
socket. Once power is connected, the touch screen start-up procedure begins.
Wait while the touch screen initializes. Continue when the Select codec to pair
with window appears. This may take a few minutes.
7.5 m
5 m
Power
adapter
Power socket
LAN socket
(Ethernet)
1.8 m
Connecting the Cisco TelePresence Touch 8”
The Touch 8” can be connected to a range of Cisco TelePresence codecs.
There are two options how to connect the Touch controller to the codec. In both
cases the connection is via the provided power adapter, as shown in the illustrations.
A. Connecting the touch screen to a codec via LAN (local area network).
B. Connecting the touch screen directly to the codec. To be able to use this option
you need a codec with two LAN connectors.
Codecs and systems using TC software must run version TC4.1 or later.
Note: The touch screen obtains its IP settings automatically from the network
(DHCP). In most cases this is preferred and you can continue with the pairing.
If you need a static IP address for your touch screen perform the steps described in
the Change the IP settings section on page 6, before continuing.

— 4 —
A list of all codecs that are in Pairing visibility mode is displayed on the touch screen.
Refresh list
Select codec to pair with
Select codec manually...
IP Settings

System name (Codec type)
[email protected]
The touch screen
menu and contact list
[email protected]
Product:
Cisco TelePresence System Codec
SIP URI:
[email protected]
H323 id:
[email protected]
Software:
TC4.1.0
IP address:
192.168.1.128
Serial number:
CBA123456789
System name (Codec type)
[email protected]
Start Pairing
Back
Back
5. Tap the codec name in the list.
Note: If your codec is not in the
list, read about What to do if your
codec is not listed on page 7.
9. Verify that the touch screen is successfully paired to your codec by checking the
codec address displayed in the top banner.
The touch screen is ready to use.
6. Review codec details and tap
Start Pairing to start the
pairing process.
7. If required, the touch screen
downloads and installs new
software from thecodec. The
touch screen automatically
restarts after the software
upgrade. This process may take
a few minutes.
8. If your codec is password
protected, you will be
prompted for an administrator
username and password to
sign in to the codec.
Continue when the menu and
contact list appear on the
touch screen.

— 5 —
BConnecting the touch screen directly to the codec
Note: To be able to use this option you need a codec with two Ethernet/LAN
connectors.
1. Enable Direct pairing on the codec. Navigate to Home>Settings > Administrator
settings > Pairing with the remote control to switch it on, or congure the
NetworkPort 2 > Mode setting via the web interface or the command line
interface.
Note: The codec’s rst Ethernet connector must be connected to LAN.
The codec is required to reboot for this change to take eect.
2. Connect the touch screen cable to the Power adapter.
3. Connect the shielded Ethernet cable between the Power adapter and the
secondEthernet connector on your codec.
CAUTION: Do not connect the codec’s secondEthernetconnector to LAN.
4. Connect the supplied power cable between the Power adapter and the power
socket. Once power is connected, the touch screen start-up procedure begins.
If required, the touch screen downloads and installs new software from the codec.
The touch screen automatically restarts after the software upgrade. This process
may take a few minutes.
Continue when the menu and contact list appear on the touch screen.
7.5 m
5 m
1.8 m
Power
adapter
On a Prole system the
codec is placed inside the
foot module.
Power socket
Connect to the
codec’s second
Ethernet connector

— 6 —
5. Verify that the touch screen is successfully connected to your codec by checking
the codec address displayed in the top banner.
The touch screen is ready to use.
The touch screen
menu and contact list
[email protected]
Change the IP settings
If you need to use static IP addresses, contact your network administrator to
get theparameters you need for your system.
i. Tap IP Settings.
ii. Select the appropriate
IPVersion, then select
Manual IPAssignment.
iii. Enter the required
parameters (a keypad
appears when you tap in a
text eld).
iv. Tap Save to activate the
changes, or Undo to leave
without saving.
Select codec to pair with
Select codec manually...
IP Settings

System name (Codec type)
[email protected]
Back
IP Settings - Touch Screen IP Settings
IP Version
IP Assignment
IP address
Subnet mask
Gateway
Link Settings
Voice VLAN Mode
Voice VLAN ID
255.255.255.0
192.168.1.1
192.168.1.130
IPv6IPv4
Settings | IP Settings - Touch Screen Undo
Auto Manual
Manual OffAuto
0
Save
Back

— 7 —
Select codec manually
Useful hints
• Remove the protective foil from the display. You may keep the foil for later
reference.
• Use the rear mounted folding foot to alter the touch screen tilt.
• Clean the display using the dry cleaning cloth provided.
• The power adapter can be fastened under a table top with screws (not
included).
• Use a cable winder (not included) to keep cables neat and organized. The
winder can be placed under a table top.
IP address or hostname
Manual connection
192.168.1.128
Start Pairing
Back
Select codec to pair with
IP Settings

Select codec manually...
What to do if your codec is not listed
If your codec is not in the list, do the following:
• Start or restart your codec to activate Pairing visibility mode (a codec is in
Pairing visibility mode for 30 minutes after it is switched on).
• Alternatively, if you have a codec with a remote control, activate Pairing
visibility mode using the codec menu: Home > Settings > Administrator
settings > Pairing > Activate pairing visibility mode.
If the codec is still not listed, you can enter its IP address manually. Perform
steps i, ii and iii in the Select codec manually frame below instead of steps 5
and 6 to the left.
Back
i. Tap Select codec manually...
ii. Enter the codec IP address
or hostname (tap in the
text eld to activate the
keypad).
iii. Tap Start Pairing to start
the pairing process.
Back
Back

On our web site you will nd an overview of the
worldwide Cisco contacts.
Go to: http://www.cisco.com/web/siteassets/contacts.
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Dr.
San Jose, CA 95134 USA