GE Allegro User manual

GE
Security
P/N 466-1822 • REV F • ISS 09OCT09
Allegro Control Panel User
Manual

Copyright © 2009 GE Security, Inc.
This document may not be copied in whole or in part or otherwise reproduced without prior
written consent from GE Security, Inc., except where specifically permitted under US and
international copyright law.
Disclaimer The information in this document is subject to change without notice. GE Security, Inc.
(“GE Security”) assumes no responsibility for inaccuracies or omissions and specifically disclaims
any liabilities, losses, or risks, personal or otherwise, incurred as a consequence, directly or
indirectly, of the use or application of any of the contents of this document. For the latest
documentation, contact your local supplier or visit us online at www.gesecurity.com.
This publication may contain examples of screen captures and reports used in daily operations.
Examples may include fictitious names of individuals and companies. Any similarity to names
and addresses of actual businesses or persons is entirely coincidental.
Trademarks and patents GE and the GE monogram are trademarks of General Electric Company.
Other trade names used in this document may be trademarks or registered trademarks of the
manufacturers or vendors of the respective products.
Intended use Use this product only for the purpose it was designed for; refer to the data sheet and user
documentation for details. For the latest product information, contact your local supplier or visit
us online at www.gesecurity.com.
FCC compliance This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against interference in a residential environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instrucitons, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipemnt and receiver.
Connect the affected equipment and the panel receiver to separate outlets, on
different branch circuits.
Consult the dealer or an experienced radio/TV technician for help.
FCC part 15 ID: B47-785B-ALGRO
IC: 867A-785ALGRO
Contact information For contact information see our Web site: www.gesecurity.com.

Content
Introduction to Allegro 1
System components 1
Communicating with the panel 2
Cleaning the panel 4
Alarms 5
Siren time-out 5
Preventing accidental alarms 5
Panic alarms 7
Basic operating commands 8
Arming and disarming your system 9
Arming level 1 9
Arming level 2 10
Arming level 3 11
Arming options 12
Quick arm 12
Keychain touchpad arming 12
Quick exit 12
Chime feature 13
Exit delay time 13
Entry delay time 13
Silent extension 14
No delay 14
Auto stay arm 15
Bypassing sensors 15
Programming 18
User access codes 18
Setting the time 19
Adjusting the panel beep volume 19
Version 20
Exiting user programming mode 20
Testing 21
Automatic tests 21
Manual tests 21
Testing central station communication 23
Allegro Control Panel User Manual i

Troubleshooting 24
Reference tables 26
System information 26
User codes 26
Keychain touchpads 26
Accidental smoke and fire alarm 26
Dialer delay 27
Entry and exit delay time 27
Automatic phone test 27
System options 28
Sensor log 29
If the power goes out 29
Conditions, displays, and sounds 29
Siren 32
Trouble beeps 33
Emergency planning 34
Your floor plan 34
Alarm system limitations 34
If your system needs service 35
ii Allegro Control Panel User Manual

Introduction to Allegro
This security system is designed to protect you, your family, and your property
whether you are on the premises or away.
This manual describes how to operate your system. It describes basic arming and
disarming commands as well as programming instructions for your system features.
The dealer or installer may have already discussed with you many details concerning
your system. Specific setup information is shown in “Reference tables” on page 26.
System components
Your security system can include the components shown in Figure 1 below and
described in Table 1 on page 2.
Figure 1: System components
1. Panel
2. Dialog Telephone Interface Module
3. Wireless touchpad
4. Keychain touchpad
5. Motion detector
6. Door/window sensor
7. Environmental sensor
Allegro Control Panel User Manual 1

Table 1: System components
Component Description
Panel The panel monitors all the sensors and devices in the system and initiates a
call to the central station in an alarm situation. The panel has a touchpad
for arming, disarming, checking status and entering data, such as access
codes.
Dialog Telephone
Interface Module
The Dialog Telephone Interface Module (DTIM) provides added security by
separating the telephone interface from the panel. If the panel is damaged
by fire or a break-in, it still reports to the central monitoring station.
Door/window sensors Door and window sensors protect the perimeter of your home by alerting
the panel when a door or window is opened.
Motion detectors Motion detectors in hallways or individual rooms detect a person moving
across the field of detection.
Environmental sensors Environmental sensors such as smoke and carbon monoxide detectors
remain alert for the presence of fire or carbon monoxide 24 hours a day.
Wireless touchpad The wireless touchpad can be carried from room to room.
Note: The Light buttons do not work on Allegro system.
Keychain touchpad Keychain touchpads are handy for simple arming and disarming functions.
They are wireless and can be carried off-site. The installer can program the
touchpad to send a police or emergency panic alarm.
Note: The keychain touchpad has not been investigated by UL.
Communicating with the panel
Touchpads allow you to communicate with the panel. In turn, the system can be set
up to communicate with you using:
• Icons and scrolling text on the display
• Status beeps from the panel speaker
• Touchpad LEDs
• Alarm sirens
Most of your commands to the panel will consist of entering the command plus a
programmed 4-digit access code.
Keychain touchpads do not require an access code. If an alarm is initiated with a
keychain touchpad, a different device must be used to disarm the system.
Icons and scrolling test
The panel uses a liquid crystal display (LCD) to communicate system status
information. The display uses icons and characters to display messages. If a message
is longer than nine characters, the first nine characters are displayed and the rest of
the message scrolls through in a marquee fashion.
2 Allegro Control Panel User Manual

Status beeps
The panel siren produces a variety of operating beeps to inform you of different
system states and operations.
A key beep is the tone you hear when you press a button on the panel or handheld
wireless touchpad. The sound confirms that the button was adequately pressed.
Status beeps come from the siren on the panel and sound when there is a change in
the current system status. Status beeps are not alarms, but they do warrant your
attention. Table 2 below describes the different status beeps provided.
Table 2: Status beeps
Type Description
Exit delay Exit delay beeps indicate that an arming command has been entered and
the countdown to arming has begun. Exit and close the door behind you
before the exit delay expires.
Entry delay Entry delay beeps indicate that you have entered the building and the
countdown to an alarm has begun. Disarm the system as soon as you enter.
Chime feature Chime feature beeps indicate that a door was opened.
Protest Protest beeps indicate that you are trying to arm the system while there is
an open door or window.
Trouble Trouble beeps indicate that there is a problem with the system or one if its
components. Pressing the * key silences the trouble beeps. If possible,
correct the situation causing the trouble beeps. If this is not possible,
contact your dealer/installer. If the problem is not corrected, trouble beeps
and messages restart 4 (if fire related) to 10 hours later. See “
Trouble beeps” on page 33 for more information.
Sensor test Sensor test beeps are the sounds the system makes during a sensor test to
indicate the number of packets the panel received. See “Sensor test” on
page 21.
LEDs
The touchpad has two LEDs that indicate the current system. The red LED is labeled
“Armed” and the green LED is labeled “Ready.” Table 3 below describes the LED
functions.
Table 3: LED functions
LED Description
Armed LED (red) Flashing = Entry or exit delay
On = Armed to level 2 (doors and windows) or level 3 (doors, windows, and
motions)
Off = Armed to level 1 (disarmed)
Allegro Control Panel User Manual 3

LED Description
Ready LED (green) On = System OK
Off = System trouble/protest (check system status)
Checking system status
Checking system status includes finding out if any sensors are open or currently
bypassed, whether or not the AC power and backup battery are working, the nature
of the most recent alarm, and more, depending on your system’s features and
equipment.
Check the system status if your system sounds trouble beeps (four short beeps every
minute) or if your panel displays Press Status.
If an alarm or system trouble condition has occurred, it is displayed on the panel
when you perform a status check. If any system trouble is active, it continues to show
up in every status check until the trouble has been corrected.
To get a system status:
1. Press Status (*) on the panel or wireless touchpad.
The system sounds beeps according to the current arming level (one beep for
level 1, two beeps for level 2, and three beeps for level 3).
The panel displays the following status information:
• Alarm memory events following the disarming of the panel.
• Abnormal sensor conditions (open, bypassed, supervisory conditions, low
battery, or trouble).
• System troubles.
If there are no current troubles, alarms, or events in alarm memory, the panel
displays System is OK.
Note: If all troubles have been resolved, press Status (*) to clear alarm memories.
Cleaning the panel
When your panel needs cleaning, spray a soft cloth with glass cleaner or slightly
dampen it with soapy water and gently wipe the panel display.
Caution: Do not spray the glass cleaner on the display or let any liquid run down into
the panel as this could cause damage to your system.
4 Allegro Control Panel User Manual

Alarms
When there is an alarm condition, the siren emits emergency tones and the panel
notifies the central station for help.
Siren time-out
The system is not automatically disarmed after an alarm, the sirens continue to
sound until the time-out period is reached. Even after the time-out stops the sirens,
the alarm is still in progress and remains so until you manually disarm the system.
The time-out period can only be programmed by your installer or dealer.
Preventing accidental alarms
Your security system is engineered with advanced technology that reduces the
chance of an accidental alarm caused by a technical problem.
Most accidental alarms occur when leaving a residence after arming the system, or
upon returning, before disarming system.
If, for example, you arm the system, then run to another room for something you
forgot, the exit delay time may expire. Once the exit delay expires, opening an armed
door or moving in front of an armed motion detector causes an alarm or starts the
entry delay.
Your system can be set up with the opportunity to abort an accidental intrusion,
police, or emergency alarm (fire alarms cannot be aborted).
If the dialer delay feature is turned on, you have a programmed amount of time
(between 15 and 45 seconds after an event, as set by your installer) to stop the panel
before it sends a false alarm to the central station. Talk to your installer or see “Dialer
delay” on page 27 to see if this feature is enabled and how much of a delay is
programmed.
Fire alarms are always reported. If an accidental fire alarm has sounded, follow your
central monitoring station’s procedures to prevent a false dispatch.
To abort a nonfire alarm:
1. When the panel displays ENTER CODE + <type of alarm>, enter your access
code.
The panel displays ABORTED and sounds one beep.
Allegro Control Panel User Manual 5

Preventing accidental alarms
Follow these guidelines to preventing accidental alarms:
• Close doors and windows before you arm your system and leave your house.
• When leaving the premises, gather the things you want to take with you so you
can exit immediately after arming the system.
• Always enter and exit within the programmed delay times.
• Make sure you leave through a door that has a delay time programmed. If you
arm your system, then leave through a door without a delay time, the siren
sounds the alarm condition immediately.
• When you return, immediately disarm your system.
• Talk to the system installer to be aware of the devices in your security system and
learn how each one operates.
• Listen to your system beeps. Take note of indicator lights and touchpad messages
indicating the current system status.
• If you have pets, ask your installer if you need pet lenses in your motion detectors
or pet immune motion sensors. Pets climb higher than you may guess and can
cause alarms when you are away.
• Check the location of your smoke detectors. Smoke detectors near bathrooms
can be tripped by steam from a shower. Smoke detectors near the kitchen can be
tripped by excessive smoke from cooking.
6 Allegro Control Panel User Manual

Panic alarms
Panic alarms are easily activated from any touchpad to quickly alert the central
monitoring station to a police of fire emergency. A panic alarm can be sent at any
time, regardless of the current arming level.
This system is designed to inform central monitoring station of the nature of the
emergency so the correct personnel can be dispatched immediately.
Each type of panic alarm sounds and reacts differently when activated. A police panic
alarm sounds a continuous tone. A fire panic alarm sounds a repeating series of three
beeps.
Police panic alarms
A police panic alarm sounds to scare off any intruder and alert neighbors to any
trouble. On a monitored system, the central station responds by calling the police.
To activate a police panic alarm from the panel:
1. Press and hold the Arm and 1 buttons until the panel responds.
To activate a police panic alarm from the wireless touchpad:
1. Press and hold the Police (*) buttons until the panel responds.
To activate a police panic alarm from a keychain touchpad:
1. Press and hold the Lock and Unlock buttons at the same time for two seconds.
Fire panic alarms
If your system includes smoke and fire detectors, it monitors the premises for smoke
and fire alarms 24 hours a day and in all arming levels.
These alarms cannot be aborted and are always reported to the central station. Since
many communities charge for dispatching the fire department in error, your dealer
may give you specific instructions to follow in the event of an accidental smoke or fire
alarm. Record these instructions in “Accidental smoke and fire alarm” on page 26.
To activate a fire panic from the panel:
1. Press and hold the Silent and Chime buttons until the panel responds.
Allegro Control Panel User Manual 7

Basic operating commands
Figure 2 below shows the panel keypad and Table 4 below describes the system’s
basic commands.
Figure 2: Panel touchpad
3
6
9
#
2
1
5
Options
8
Chime
4
St at us
7
No Delay
Sil ent
Quick Exit
Disarm
Back
*
0
Bypass
Sel ect
3
6
9
2
1
5
8
4
7
0
Arm
Table 4: Basic system commands
Task Command
Check system status Press Status (*)
Disarm the system Press Disarm + code
Arms doors and windows Press Arm + code
Arm doors and windows, no delay Press Arm + code + No Delay (4)
Arm motions, doors and windows Press Arm (twice) + code
Arm motions, doors and windows, no delay Press Arm (twice) + code + No Delay
Arm system silently Press Silent + Arm + code
Turn chime feature on and off (only when system
is unarmed)
Press Chime (7)
Identify open sensor, trouble conditions, and
alarms in memory
Press Status (*)
Bypass a zone Press Bypass (#) + primary code
Quick exit (for use when system is armed) Press Quick Exit (starts a two-minute timer for use
of one entry/exit door)
Police panic Press and hold both the Arm and 1 buttons until
the panel indicates the alarm
Fire panic Press and hold both the Silent and Chime (7)
buttons until the panel indicates the alarm
8 Allegro Control Panel User Manual

Arming and disarming your system
Since your security needs may vary throughout the day, this system was designed
with the following three arming levels:
• Level 1 (disarmed). Intrusion detection off. Smoke, heat, and environmental
sensors remain active.
• Level 2 (doors and windows). Perimeter protection on. Interior sensors are not
active.
• Level 3 (motions, doors and windows). All perimeter and interior sensors are
active.
By arming your system to a particular level, only those sensors programmed to
detect in that arming level report alarm conditions to the panel. No matter which
level your system is in, all sensors programmed to be active 24 hours a day continue
to report alarm conditions. These sensors include smoke detectors, panic buttons,
and environmental sensors.
Arming level 1
Use arming level 1 (disarmed) to turn off intrusion/burglary protection for your system
when security is not a concern. Environmental sensors (smoke, heat, carbon
monoxide) remain active. Indoor motion sensors and perimeter sensors such as
doors and windows are inactive.
Other situations for level 1 arming include:
• Disarm the system when you enter the armed premises through a designated
delay door.
• Disarm the system before opening a window or door to prevent an alarm.
• Disarm the system to turn off the sirens when an alarm condition occurs.
To disarm to level 1 using the panel keypad:
1. Press Disarm once.
The panel displays Enter Code to DISARM.
2. Enter your access code.
The panel displays the current time and the system sounds one beep.
To disarm to level 1 using a keychain touchpad:
1. Press Unlock.
Allegro Control Panel User Manual 9

To disarm to level 1 using a wireless touchpad:
1. Press Disarm and enter your access code.
Arming level 2
There are times when you want intrusion protection, but still want the freedom to
move around inside your home without setting off an alarm. In this situation, set your
system to level 2 (doors and windows) to turn off the interior motion sensors.
Note: To arm to level 2 from level 3, you must first disarm and then rearm the system.
To arm to level 2 using the panel keypad:
1. Close all protected perimeter doors and windows.
2. Press Arm once.
The panel displays Enter Code to ARM.
3. Enter your access code.
The panel displays EXIT TIME XX and Lock Doors and Windows. The
system sounds two beeps.
4. If you are leaving the premises, exit through a designated delay door before the
delay time expires.
Note: If the quick arm feature is on, an access code is not required to arm the system
to level 2.
To arm to level 2 using a keychain touchpad:
1. Press Lock.
The system sounds two beeps.
To arm to level 2 using a wireless touchpad:
1. Press Arm Doors and Windows and enter your access code.
10 Allegro Control Panel User Manual

Arming level 3
When everyone will be away from the premises, set your system to level 3 (motions,
doors, and windows) for maximum protection. In level 3 all sensors are active
including perimeter door and window sensors and interior motion detectors.
To arm to level 3 using the panel keypad:
1. Close all perimeter doors and windows.
2. Press Arm twice.
The panel displays Enter Code to ARM.
3. Enter your access code.
The panel displays EXIT TIME XX and Lock Motion Sensors, Doors
and Windows. The system sounds three short beeps.
4. Exit through a designated delay door before the delay time expires.
Note: If the quick arm feature is on, an access code is not required to arm the system
to level 3.
To arm to level 3 using a keychain touchpad:
1. Press Lock twice to go from level 1 to level 3, or once to go from level 2 to level 3.
The system sounds three short beeps.
To arm to level 3 using a wireless touchpad:
1. Press Arm Motion Sensors and enter your access code.
Allegro Control Panel User Manual 11

Arming options
The system provides the arming options described below.
Quick arm
This option lets you arm your system without using an access code. You will still need
to enter an access code to disarm the system. Your dealer/installer can turn this
option on or off for you. See “System options” on page 28 to see if this feature is
available to you.
To use the quick arm option:
1. To arm to level 2 with quick arm enabled, press Arm once.
— or —
To arm to level 3 with quick arm enabled, press Arm twice.
Keychain touchpad arming
Your installer can set up your keychain touchpad to arm the system in one of the
following ways:
• Press Lock to arm the system directly to level 3 with no delay. Using this method,
you would not be able to arm to level 2 with your keychain touchpad.
• Press Lock to increase the arming level each time it is pressed (level 1 to level 2,
level 2 to level 3). The exit delay time begins.
Quick exit
This option is useful when you want to quickly exit and reenter a door without
disarming your system.
To use the quick exit option:
1. When the system is armed to level 2 or 3, press Quick Exit.
The panel displays QUICK 120, and begins a two-minute countdown.
2. Open the door and exit.
3. Reenter the door within two minutes and close the door.
The system rearms after the two-minute countdown.
12 Allegro Control Panel User Manual

Chime feature
When the chime feature is on, opening a door or window causes the panel to beep
twice and display the sensor’s name. You can only turn the chime feature on or off
when the system is disarmed (level 1).
To turn the feature on or off, press Chime (7). When on, the panel alternates between
displaying the current time and CHIME ON.
Exit delay time
After arming your system, you need time to exit the building so you won’t set off an
alarm. Exit delay is the period of time you have after arming the system to leave the
premises through a designated delay door.
After you arm the system to level 3, the panel siren sounds three quick status beeps
indicating that the system accepted the command and has started the exit delay
time. During the exit delay time, the system sounds one beep every four seconds. Exit
the premises before the exit delay time expires. During the last 10 seconds of the exit
delay time, you will hear a beep every second, warning you that the time is about to
expire. At this point, leave quickly or disarm the system. When the delay expires, there
will be three more quick status beeps. These beeps indicate that the exit delay has
ended. Opening an armed door or window after the exit delay has expired causes an
alarm or starts the entry delay.
Your installer will work with you to decide which doors should be delay doors and
determine the delay time that will work best for you and your family. The installer will
program your system and record the information in “Entry and exit delay time” on
page 27.
Entry delay time
Upon returning to the premises, you need enough time to open the door and get to a
touchpad to disarm the system. Entry delay time is the period of time you have to
disarm the system after you open a designated delay door.
When you unlock and enter the designated delay door, the panel siren sounds one
beep every four seconds indicating that the entry delay time has begun and that you
must disarm the system to avoid setting off an alarm. During the last 10 seconds of
the entry delay time, you will hear one beep every second.
Your installer will work with you to decide which doors should be delay doors and
determine the delay time that will work best for you and your family. The installer will
program your system and record the information in “Entry and exit delay time” on
page 27.
Allegro Control Panel User Manual 13

Silent extension
Your system can be set up so that the delay time is restarted if you reopen the delay
door during your initial delay time. This is useful if, after arming the system, you walk
out the door, and then remember something you forgot. You can reenter and exit
through the delay door without disarming and rearming the system.
Note: The exit extension works on the first reentry only.
If your system is not programmed for this feature, you must disarm the system when
you reenter the armed premises to avoid setting off an alarm. Your dealer/installer
can turn this feature on or off for you. See “System options” on page 28 to determine
if this feature is currently enabled.
No delay
You can choose to turn off the entry and exit delays, causing the delay doors to arm
immediately by pressing No Delay (4) within five seconds of arming the system.
Anyone entering or exiting the premises through the delay door when the system is
set to no delay would immediately cause an alarm.
The no delay feature is normally used in the following situations:
• When you are staying at home, after you have armed the system.
• When you are arming the premises from the outside (you must have an installer
programmed keychain touchpad with the arm feature enabled to do this).
Your dealer/installer can turn this option on or off for you. See “System options” on
page 28 to see if this feature is currently enabled.
To arm to level 2 (or 3) with no delay using the panel keypad:
1. Close all perimeter doors and windows.
2. Press Arm once (or twice).
3. Enter your access code.
The system sounds two (or three) beeps.
4. Immediately after hearing the beeps, press No Delay (4).
The panel displays the current time and Arm Doors and Windows – No
Delay (or Motion Sensors, Doors and Windows – No delay).
Note: If the quick arm feature is enabled, an access code is not required.
To arm to level 2 (or 3) with no delay using the wireless touchpad:
1. Press the desired arm button.
2. Enter your access code.
14 Allegro Control Panel User Manual

3. Press No Delay.
To arm directly to level 3 with no delay using the keychain touchpad:
1. Press Lock.
Changing the arming level restores delay doors to their normal exit and entry delay
times.
Auto stay arm
The auto stay arm feature helps cut down on false alarms. If you arm the system to
level 3, and do not leave the premises within the exit delay time:
• Auto stay arm feature enabled. The system can tell that no one opened and
closed a delay door within the delay time. It assumes that someone is still inside
and the panel arms to level 2 to avoid a false alarm. Your movement inside the
premises does not cause an alarm.
• Auto stay arm feature disabled. The system arms to level 3 regardless of whether
or not a delay door has been opened and closed. Your movement inside the
premises could activate a motion detector, causing an alarm.
Your dealer/installer can turn this feature on or off for you. See “System options” on
page 28 to see if this feature is currently enabled.
Note: If you arm to level 3 with the no delay feature enabled, the auto stay arming
feature is cancelled.
Bypassing sensors
It is possible to arm your system while leaving a door or window open. This is useful if,
for example, you like to sleep with a window open.
If the door or window is protected with a sensor, the system must be told to ignore or
bypass that sensor when it is open. All other sensors remain active.
When you bypass a sensor, you are allowing that sensor (usually a door or window) to
go unprotected. You cannot bypass heat, smoke, and carbon monoxide sensors or
the DTIM.
There are two methods for bypassing a sensor, direct and indirect.
Direct bypass. Use this method after arming the system, to bypass a door/window
sensor before you open them. You must know the sensor or number of the door or
window you wish to bypass (see “Sensor log” on page 29).
You can only direct bypass sensors from the panel touchpad and you must use the
primary access code.
Allegro Control Panel User Manual 15

Only sensors active in the current arming level can be bypassed. Attempting to
bypass a sensor that is already bypassed activates or unbypasses the sensor.
To bypass sensors directly:
1. Close all doors and windows.
2. Arm your system to the desired level.
3. Press Bypass (#).
The panel displays Enter Code to BYPASS.
4. Enter your primary access code.
The panel displays the sensors that are active in that level and can be bypassed in
the system.
5. Scroll through the list of sensors and press Select (#) to select the sensor to
bypass.
The panel displays ZONE XX OFF and the press status icon turns on (the status
message includes the bypassed and open sensors).
Note: If a key is not pressed for five seconds, the panel exits bypass sensor mode.
The bypassed door or window can now be opened.
Indirect bypassing. Use this method if you are arming the system and would like to
bypass doors and windows that are already open.
To bypass sensors indirectly:
1. Leave open only those doors and windows that are to remain open. Close all
others.
2. Arm your system to the desired level.
The panel emits protest beeps and displays PROTEST and ZONE XX OPEN.
3. Press Bypass (#) to immediately bypass the sensor, or allow the delay time to
expire and the sensors bypass automatically.
The system sounds arming level beeps to indicate that the system is armed and
open sensors have been successfully bypassed.
To confirm that a sensor was bypassed, press Status (*). The panel lists bypassed and
opened sensors or zones.
16 Allegro Control Panel User Manual