CityGrow Systems CG800 Series User manual

i
CG800 SERIES
ZIGBEE WIRELESS SWITCH
USER MANUAL
VERSION 1.1
17 JANUARY,2014
Disclaimers and Copyright
Nothing contained in this publication is to be construed as granting any right, by implication or otherwise, for the
manufacture, sale, or use in connection with any method, apparatus, or product covered by letters patent, or as
insuring anyone against liability for infringement of letters patent.
Efforts have been made to ensure the accuracy and reliability of the data contained in this publication; however,
Citygrow Energy Systems Limited. makes no representation, warranty, or guarantee in connection with this
publication and hereby expressly disclaims any liability or responsibility for loss or damage resulting from its use or
from the use of any product or methodology described herein; for any violation of any federal, state, or municipal
regulation with which this publication may conflict; or for the infringement of any patent from the use of this
publication. Nothing contained in this publication should be viewed as an endorsement by Citygrow Energy Systems
Limited. of any particular manufacturer’s products.
CG800S1
One Gang Switch
CG800S2
Two Gang Switch
CG800S4
Four Gang Switch
CG800DM
One Gang Dimmer
CG800DM2
Two Gang Dimmer
CG800S2-CCP
One Gang Curtain
Control Switch
CG800S4-CCP
Two Gang Curtain
Control Switch

ii
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE
PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the
user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the literature accompanying
the product.
IMPORTANT SAFETY INSTRUCTIONS
READ BEFORE OPERATING EQUIPMENT
This product was designed and manufactured to meet strict quality and safety standards.
There are, however, some installation and operation precautions which you should be particularly aware of.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that produce
heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in
any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

1
Table of content
1. Introduction................................................................................................. 1
2. Understanding of the product........................................................................ 2
3. Dimensions.................................................................................................. 3
4. Wiring-CG800S1, S2, S4, DM, DM2 ................................................................ 4
5. Wiring-CG800S2-CCP, S4-CCP ....................................................................... 6
6. Installation .................................................................................................. 7
7. Operation instruction .................................................................................... 9
7.1. CG800S1, S2, S4 .............................................................................. 9
7.2. CG800DM, DM2 .............................................................................. 10
7.3. CG800S2-CCP, S4-CCP .................................................................... 11
7.3.1. Setting the open and close travel distant for the curtain. ......... 12
8. Adding the product to your Home Wireless ZigBee Network ........................... 14
9. Clear Memory ............................................................................................ 15
10. Specification .............................................................................................. 17

1
1. Introduction
Thank you for buying Citygrow’s product. CG800 Series is both powerful and easy to
use and install. These products are specially designed for Home Automation
application.
Description
1. ZigBee wireless remote control.
2. Based on IEEE 802.15.4.
3. 2.4GHz radio frequency.
4. CG800S1, S2, S4, DM, DM2 is for lighting control
5. CG800S2-CCP, CG800S4-CCP is for control of electronic curtain or window blind.
6. LED indicator for on/off status.
7. Load/ loads are directly driven by the build-in driver.
8. Control button can be configured to become two way function.
9. Control button can be configured to become scene function.
10. Support iPhone, iPad and Android mobile control if CG102BS Base station is purchased.
11. Control button graphics can be tailor-made per customer requirement.
12. Mounted in a standard UK wall box.
13. No EIB / Bus required
14. Easy to install.

2
2. Understanding of the product
Frame
Button panel
Front view
Control unit
Front view
Mounting hole
Connector to
control unit
Metal clip to fix
the button panel
Load terminals
Live (Brown)
Neutral (Black)
Model number
plate
Control
button
Programming port
Reset
button
Control unit bottom
view
Button panel
bottom view
4
3
2
1

3
Load terminals
1
2
3
4
CG800S1 One Gang Switch
Load1
NC
NC
NC
CG800S2 Two Gang Switch
Load1
Load2
NC
NC
CG800S4 Four Gang Switch
Load1
Load2
Load 3
Load 4
CG800DM One Gang Dimmer
Load1
NC
NC
NC
CG800DM2 Two Gang Dimmer
Load1
Load2
NC
NC
CG800S2-CCP One Gang Curtain Control Switch
Motor 1
Forward
Motor 1
Backward
NC
NC
CG800S4-CCP Two Gang Curtain Control Switch
Motor 1
Forward
Motor 1
Backward
Motor 2
Forward
Motor 2
Backward
3. Dimensions
Load terminal to Model number chart
85mm
85mm
40mm
27.8mm

4
4. Wiring-CG800S1, S2, S4, DM, DM2
Lamp
Load
Wall box
Neutral
Distribution panel
Live
Notes:The Neutral wire of load is closely connected to the Neutral point of CG800.
Situation 1: Live , Neutral and Load wires are ready at wall box
4
3
2
1
Load
terminals
(See Table: 4A)
CG800S1
CG800S1
Load
Lamp
Wall box
Distribution panel
Situation 2: Neutral wire is only ready at ceiling.
Notes:The Neutral wire of load is closely connected to the Neutral point of CG800.
4
3
2
1
Load
terminals
Live
Neutral
(See Table: 4A)

5
Table 4A
Load terminals
1
2
3
4
CG800S1 One Gang Switch
Load1
NC
NC
NC
CG800S2 Two Gang Switch
Load1
Load2
NC
NC
CG800S4 Four Gang Switch
Load1
Load2
Load 3
Load 4
CG800DM One Gang Dimmer
Load1
NC
NC
NC
CG800DM2 Two Gang Dimmer
Load1
Load2
NC
NC
CG800S2-CCP One Gang Curtain
Control Switch
Motor 1
Forward
Motor 1
Backward
NC
NC
CG800S4-CCP Two Gang Curtain
Control Switch
Motor 1
Forward
Motor 1
Backward
Motor 2
Forward
Motor 2
Backward
Before getting started
WARNING! Install in accordance with all national and local electrical codes.
IMPORTANT! Citygrow® is not liable for any damage incurred with the misuse of this product.
IMPORTANT! Pre-setup can only be done by a professional worker or manufacturer agent.
WARNING! It must be installed by a qualified electrician in accordance with all applicable regulations and building
codes. Improper wiring can result in personal injury or damage to control units or other equipment. Always turn off
circuit breaker or remove main fuse from power line before doing any work. To avoid overheating and possible damage
to equipment.
WARNING! Do not operate when any lamps removed or burned out; replace any burned out lamps immediately; use
only transformers that incorporate thermal protection or fused primary windings. ! This product is designed for residential
and commercial use, for indoor use only.

6
5. Wiring-CG800S2-CCP, S4-CCP
Live
Load 1
Wall box
Neutral
Conduit
Conduit
Curtain motor (AC)
Load 2
Wall box
Wall
Notes:The Neutral wire of load is closely connected to the Neutral point of CG800.
Distribution panel
4
3
2
1
Load
terminals
(See Table: 4A)
CG800S2-CCP
Before getting started
WARNING! Install in accordance with all national and local electrical codes.
IMPORTANT! Citygrow® is not liable for any damage incurred with the misuse of this product.
IMPORTANT! Pre-setup can only be done by a professional worker or manufacturer agent.
WARNING! It must be installed by a qualified electrician in accordance with all applicable regulations and building
codes. Improper wiring can result in personal injury or damage to control units or other equipment. Always turn off
circuit breaker or remove main fuse from power line before doing any work. To avoid overheating and possible damage
to equipment.
WARNING! Do not operate when any lamps removed or burned out; replace any burned out lamps immediately; use
only transformers that incorporate thermal protection or fused primary windings. ! This product is designed for residential
and commercial use, for indoor use only.

7
6. Installation
In order to install the product correctly, please follow the below steps:
STEP 1: IMPORTANT! Turn off main power at the main switch board.
STEP 2: Loosen the screws of the original wall switch. Remove the switch and
disassemble the wiring.
STEP 3: Connect the main power cable to the Live and Neutral terminals and the
load cable to the Load terminals at the rear cabinet of the product.
STEP 4: Fasten the screws of all terminals and check that the wires are properly
secured. Retrofit the switch into the standard switch box and mount it on the wall by
fastening the two screws at the rear of the switch box.
wall box
CG800
power unit
CG800
button panel
CG800 frame
Screw x 2 pcs
Screw x 4 pcs

8
STEP 5: Push the ON/OFF Button to test whether the wiring has been connected
correctly. If the ON/OFF Button does not function as expected, please check the
wiring connection again.
Notes: Use standard UK wall box BS4662; minimum 35mm deep. During installation of the
wall box, it is recommended to embed the wall box deeper inside the wall in order to give
more room to install the product. The room inside is recommended to have 50mm deep.

9
7. Operation instruction
7.1. CG800S1, S2, S4
COVER PLATE
1
1. Cover
BUTTON HOLDER
2
4
5
3
Master Kitchen
2. Label/LED Indicators
3. ON/OFF Buttons
4. Programming Port
5. Reset Button
1. Press ON/OFF Button once to toggle between ON and OFF.
-BRIGHT LED indicates that the Switch is ON.
-DIMMED LED indicates that the Switch is OFF.

10
7.2. CG800DM, DM2
COVER PLATE
1
1. Cover
MAIN UNIT
2
5
6
4
Foyer 3
2. Dim Up/ LED Indicator
3. Label/LED Indicator
4. Dim Down/ LED Indicator
5. Programming Port
6. Reset Button
1. Press the Dim Up/Dim Down button ONCE to Toggle between ON and OFF.
-LED FLASHING indicates that that the Button was pressed and dimming
is in progress.
-When the LED stops flashing, it indicates that the dimming is complete.
2. Press and HOLD the Dim Up/Dim Down button to begin dimming.
-Release the button at desired level.

11
7.3. CG800S2-CCP, S4-CCP
COVER PLATE
1
1. Cover
BUTTON HOLDER
2. LED Indicator
3. Open/Close Button
4. Reset Button
5. Programming Port
1. Press the Open/Close Button once to control the electric curtain.
- When the electric curtain is stopped, press the OPEN button to open the
electric curtain.
- When the electric curtain is stopped, press the CLOSE button to close the
electric curtain.
- When the electric curtain is running, press ANY button to stop the electric
curtain.
2
3
4
5

12
7.3.1. Setting the open and close travel distant for the curtain.
The function of the Learning Mode in the CG800S2-CCP or CG800S4-CCP is to
program the duration of the curtain Opening/Closing time.
In order to perform the Learning Mode function, please follow the below steps:
STEP 1
-Press the CLOSE Button until the
curtain is fully closed.
NOTE: You may have to press the
Button once or more times in
order for the curtain to be fully
closed.
STEP 2
-Press and HOLD the Reset
Button.
-While still holding the Reset
Button, press and HOLD the Open
Button.
STEP 3
-Release the Reset Button.
-Wait until the LED Indicators
begins BLINKING.
-Release the Open Button.

13
NOTE: The curtain should be
opening at this point.
STEP 4
-Once the curtain is fully opened,
press and release any Button.
NOTE: The duration of the
Opening/Closing time will be
stored once the Button is pressed.
STEP 5
-Use a thin object to press the
Reset Button again.
-The learning process of the
CG800S2-CCP or CG800S4-CCP
has now finished.

14
8. Adding the product to your Home Wireless
ZigBee Network
STEP 1
Open the front cover, you will
see a 5 pin connector
programming port.
STEP 2
Plug the CG101UT5 cable into
the 5 pin socket of the product,
and then plug the other end of
the CG101UT5 cable into the mini
USB end of the CG101UTC cable.
STEP 3
Plug the CG101UTC cable into
the USB port of a PC that is
installed with Citygrow’s
HomeNET Planner Software.
STEP 4
Refer to the user manual of
“HomeNET Planner” Software to
program and set the address of
the product.
2
2
3

15
9. Clear Memory
Clearing the memory inside of the product will result in:
1. The product will no longer reply to any Panels that it had previously bound to.
2. The product will no longer reply to any Remotes that it had previously bound to.
In order to perform the Clear Memory function, please follow the below steps:
STEP 1
-Press and HOLD anyone of the ON/OFF Button.
STEP 2
-CONTINUE holding onto the ON/OFF Button.
-Press and release the Reset Button once.
STEP 3
-Wait until the LED Indicator begins BLINKING.
-Release the ON/OFF Button.

16
STEP 4
-Press and release the ON/OFF Button again to stop blinking.
STEP 5
-Press and release the Reset Button.
-The memory inside of the product has now been cleared.

17
10. Specification
CG800S1
CG800S2
CG800S4
CG800DM
CG800DM2
CG800S2-
CCP
CG800S4
-CCP
Description
One
Gang
Switch
Two
Gang
Switch
Four Gang
Switch
One Gang
Dimmer
(Leading
Edge
Dimming)
Two Gang
Dimmer
(Leading
Edge
Dimming)
One Gang
Curtain
Control
Switch
Two
Gang
Curtain
Control
Switch
Load current (A)
10A
5A x 2
2.5Ax4
600W
300W x 2
5A
5Ax2
Minimum Load
NA
5W
5W / gang
NA
NA
Load type
Incandescent, Halogen, Electronic
( Solid State) Low Voltage (ELV)
Transformers, Magnetic ( Iron Core,
Inductive) Low Voltage ( MLV)
Transformers, Fluorescents, Compact
Fluorescents, LEDs, Motors
1. Incandescent,
Halogen, Magnetic
(Iron core, Inductive)
Low Voltage (MLV)
Transformers,
2. Leading Edge
Dimmable
Fluorescents,
Compact
Fluorescents and
LEDs, see remarks 3.
4.
AC motor
AC motor
Maximum number of
devices included in scene
setting** ( Remarks 1, 2)
50
50
50
50
50
NO
NO
**Remarks:
1. When up button is used for dimming up function, the down button cannot be programmed as scene function
2. Maximum number of devices programmed into the whole product is limited to 50 devices
3. The maximum load requirements for fluorescent, CFL and LED loads can vary greatly depending upon the specific
fixture and /or bulb being used.
4. When dimming transformer is connected to CG800, make sure “dimmable” and “leading edge” type is used.
Furthermore, the dimming performance varies greatly from manufacturer to manufacturer of the bulb and the
dimming transformer. It is recommended to test the matching performance before mass deployment.
Minimum dimming level
setting
NO
NO
NO
YES
YES
NO
NO
Memory dim function
NO
NO
NO
YES
YES
NO
NO