Clare Controls ClareHome CLIQ.PANEL Assembly instructions

© Clare Controls, LLC. 1 / 2 Doc ID –1298 • REV 02
CLIQ.PANEL Kit Installation Sheet
Last modified: 09/29/16
Description
The ClareHome CLIQ.PANEL provides adjustable support for
a CLIQ device. Use the panel mount when placing the CLIQ
vertically in an enclosure panel.
Unpacking the CLIQ.PANEL
Remove all contents from the CLIQ.PANEL packaging and
ensure you have the following items.
1 × Leviton Base (p/n 200-1750-4)
1 × Universal Slide (p/n 200-1749-3)
3 × Leviton Push Lock Pins (p/n 100-1299-0)
WARNING: Hazard of electrical shock. Exercise extreme
caution to avoid physical contact with bare connectors and
terminals.
Installation
The CLIQ.PANEL is designed to sit vertically in a structured
enclose panel. The kit has five pieces: the Leviton Base, the
Universal Slider, and three Leviton Push Lock Pins. The slider
attaches to the enclosure using the Leviton pins, and then the
base rests on the slider.
To attach the Universal Slider to the enclosure:
1. Push the base of the Leviton Push Lock Pin into the
structured enclosure until they snap into place.
See Figure 1, items 3 and 4.
Note: When placing the pins, ensure that there is enough
room for the base and CLIQ unit.
2. Place the flat back side of the slider in the enclosure,
aligning it with the Leviton pins in the enclosure. See
Figure 1, item 2.
3. Push the Leviton Push Lock Pins through the holes in the
slider to their base in the enclosure, verifying that the pin
is fully inserted in the base.
Figure 1: Universal slider connection to the structured enclosure
(1) Leviton Push Lock Pin
(2) Universal Slider
(3) Leviton Push Lock Pin base
(4) Structured enclosure
To attach the CLIQ to the Leviton Base:
1. Hold the CLIQ unit with the rear connectors and ports
facing upward.
2. Align the CLIQ’s feet to the flat surface on the front of the
base. See Figure 2.
3. Press the CLIQ onto the base.

2 / 2 Doc ID –1298 • REV 02
The CLIQ’s faceplate rests on the bottom ledge of the
Leviton Base and the magnets in the CLIQ secure its
position.
Figure 2: Side view of the CLIQ connecting to the Leviton Base
(1) CLIQ
(2) Rear of the CLIQ unit
(3) Leviton Base
Warranty information
Clare Controls offers a three (3) year limited warranty on
original Clare Controls components, from the date of
shipment from Clare Controls. To view complete limited
warranty details, including limitations and exclusions,
www.clarecontrols.com/warranty.
Scan the code to
view product
warranty details.
To attach the Leviton Base to the Universal Slider:
1. Align the base’s hooks over the open slots in the Universal
Slider.
2. Lower the base, ensuring that the hooks continue into the
slider.
3. Move the base left or right on the slider to attain the
desired position.
Figure 3: Leviton Base attached to the Universal Slider:
]
(1) Leviton Base with CLIQ attached
(2) Base’s hooks
(3) Universal Slider
Specifications
Dimensions (W × H × D)
Leviton Base
7.75 × 6.375 × 2.125 in.
(196.85 × 161.925 × 53.975 mm)
Universal Slider
6.625 × 2 × .375 in.
(168.275 × 50.8 × 9.525 mm)
Contact information
Clare Controls.
7519 Pennsylvania Ave, Suite 104
Sarasota, FL 34243
Support: 941.404.1072
Fax: [phone]
[email protected]
www.clarecontrols.com