Clarion UNGO MS2105 User manual

MS2105 owner.qxd 8/25/2003 4:21 PM Page 1

2
CONTENTS
1. Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Ungo-Net Interface Introduction . . . . . . . . . . . . . . . . . . . . . . 4
3. Remote Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1 Remote Transmitter Layout . . . . . . . . . . . . . . . . . . . . 5
3.2 Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 5
4. Security System Operation . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.1 Arming Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.2 Remote Sensor Bypass . . . . . . . . . . . . . . . . . . . . . . . 6
4.3 Passive Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
4.4 Disarming Operation . . . . . . . . . . . . . . . . . . . . . . . . . .6
4.5 Tamper Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.6 Silent Arming / Disarming . . . . . . . . . . . . . . . . . . . . . . 7
4.7 Driver’s Door Priority Unlock . . . . . . . . . . . . . . . . . . . 7
4.8 Auto Rearm Feature . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.9 Ignition Controlled Door Locks . . . . . . . . . . . . . . . . . . 7
4.10 Remote Panic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.11 Emergency Override . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.12 Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.13 Optional Trunk Release . . . . . . . . . . . . . . . . . . . . . . . 9
4.14 Optional Trunk Disarm Feature . . . . . . . . . . . . . . . . . 9
4.15 Programming Remote Transmitters . . . . . . . . . . . . . . 9
5. Remote Start Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.1 Remote Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.2 Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.3 Stop and Go . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.4 Auto Cold Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6. LCD 2-way Transmitter (MS2107) . . . . . . . . . . . . . . . . . . 11
6.1 Programming LCD 2-way Remote Transmitters . . . . . 11
7. User Selectable Programming Options . . . . . . . . . . . . . . . 12
5.1 Programmable Options . . . . . . . . . . . . . . . . . . . . . . . 12
5.2 Entering User Programming . . . . . . . . . . . . . . . . . . . 13
5.3 Default Reset For User Programming . . . . . . . . . . . . 13
8. Reference Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.1 Transmitter Operation . . . . . . . . . . . . . . . . . . . . . . . 14
6.2 Status Indicator (LED) Functions . . . . . . . . . . . . . . . .14
6.3 Siren Chirp Status . . . . . . . . . . . . . . . . . . . . . . . . . . .14
9. Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
10. Installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
MS2105 owner.qxd 8/25/2003 4:21 PM Page 2

3
1. FEATURES
The Ungo MS2105 and MS2107 are state-of-the-art combination vehicle security and
remote controlled car starter systems. These systems offer features designed to deter and
detect potential intrusions to your vehicle, and send an alert signal when a zone is violated.
These systems will inform the user of any bad switches or sensors that may be causing
the system to function improperly, and when triggered the violated zone will be identified.
Your Ungo system protects both you and the contents of your vehicle with features such
as panic mode, dome light illumination, and ignition controlled door locking.
In addition to security features, the MS2105 and MS2107 will safely start your car by
remote control, without your key in the ignition. If your vehicle is powered by a diesel
engine, the ignition will turn on for several seconds prior to starting the engine, in order for
the glow plugs to warm up.
Once the engine is remote started, your preset accessories (heater/air conditioner) will be
turned on to provide you with the maximum comfort when you enter the vehicle. After
activation, the vehicle will run for approximately 15 minutes (or 25 minutes if selected by
your installer at the time of installation) before automatically shutting off.
The MS2107 adds the convenience and security of 2-way operation with LCD display
confirmation. The LCD display provides real-time information about the status of your
vehicle including arm/disarm confirmation, triggered sensor identification, engine running
indication, and more. For a complete description of the LCD transmitter functions, please
see the 2-way transmitter supplement included with the MS2107.
Note: Some features may require additional parts and labor, and may not be appropriate for certain
vehicles. Consult your authorized Ungo dealer for assistance.
Standard Features
•Two 5-Button VariCode
3
1-way
Remote Transmitters ( MS2105 )
or
•One 5-Button VariCode
3
1-way
Remote Transmitter and One 2-way
LCD Transmitter ( MS2107 )
•Status Indicator (LED)
•Multi-Tone 120dB Siren
•Dual Stage Shock Sensor
•Built-in Starter Disable
•Coded Emergency Override
•Ungo-Net Interface
•Flashing Parking Lights
Optional Features
•Keyless Entry
•Remote Trunk/Hatch Release
•Dome Light Supervision
•Hood and Trunk Protection
•Power Window Roll Up
•Driver's Door Priority Locks
•Radar Sensor
•Remote Head Light Control
MS2105 owner.qxd 8/25/2003 4:21 PM Page 3

4
2. Ungo-Net Interface Introduction
The MS2105 and MS2107 are equipped with Ungo’s newest and most revolutionary
technology to date, the Ungo-Net bus system. Ungo-Net is a network system that allows
expansion, flexibility, and superior vehicle security through digital communication. This is
established through a PC link through either a computer or PDA, similar to a USB port on
a PC. Utilizing this interface, the alarm system and remote transmitters can be configured
to best suit the needs of the operator. This includes arming mode selections, auxiliary
functions, multiple vehicle operation, transmitter configuration, and interface modules.
For additional convenience and operation, households with multiple vehicles can utilize a
single remote transmitter to operate 2 vehicles. Eliminating the cumbersome cluster of
multiple remote transmitters.Also, the remote transmitters can be customized to better suit
the needs of the operator. The Arm and Disarm buttons can be consolidated into the one
button with the remaining buttons controlling assignable features.
Capitalizing on Ungo-Net, an optional LCD transmitter kit can be added to the security
system. This transmitter features 2-way communication with audible and visual
confirmation that provides vehicle status information and alerts the operator to violation
attempts.
In addition, system configuration, software upgrades, and diagnostics can be performed
through the Ungo-Net port. Thus allowing the Ungo dealer to maintain the utmost
protection and serviceability of the security system. Ungo-Net also allows the dealer to
troubleshoot false triggers and calibrate sensors quickly.
Ungo-Net Accessories
PCLINK : Includes Ungo-Net software, serial cable, instructions, and power supply.
FMKIT : Includes SAA217T (LCD transmitter), extended range antenna, instructions,
and transceiver module.
AUX BOX : Includes receiver module, wiring harness, and instructions.
MS2105 owner.qxd 8/25/2003 4:21 PM Page 4

5
3. REMOTE TRANSMITTER
3.1 Remote Transmitter Layout
The Ungo MS2105/MS2107 comes with one or two VariCode
3
Remote Transmitters
used to control the system’s features. Each time a transmitter button is pressed, the
LED will flash to indicate that a transmission is taking place.
Button 1 Arms the system and locks the doors.*
Button 2 Disarms the system and unlocks the doors.* If the optional Driver’s Door
Priority Unlocking feature is installed, pressing Button 2 Disarms the system and
unlocks only the driver’s door. Pressing Button 2 again unlocks all doors.
Button 3 Activates the system’s auxiliary 1 output (usually used for trunk release).*
Button 4 Activates the system’s remote start feature.
The Level Shift Button temporarily changes the function of buttons 1-4 allowing
expanded operation and multi-car compatibility. Each time the Level Shift button is
pressed, a new level of commands are accessed up to a maximum of four levels (Level
Shift three times). Note: pages 3 and 4 are reserved for channel expansion modules or
multi-car operation. See your Authorized Ungo Dealer for details.
* Optional feature
3.2 Battery Replacement
Your Ungo remote transmitter uses a 12 volt alkaline battery (type 23A), which will need
to be replaced from time to time. Under normal conditions, the battery may last more
than 6 months before it needs replacement. When your remote transmitter’s battery
needs replacement, you will notice a decrease in operating range or a decrease in the
brightness of the transmitter’s LED indicator.
To change the battery, remove the 2 screws at the back of the transmitter and carefully
separate the top and bottom halves of the transmitter case. Insert the new battery,
carefully observing proper polarity, then replace the cover.
Auxiliary 1
Auxiliary 2
w/ Shift
Arm/Lock
Silent Arm
w/ Shift
Disarm/Unlock
Silent Disarm
w/ Shift
Level Shift
Start
MS2105 owner.qxd 8/25/2003 4:21 PM Page 5

6
4. SECURITY SYSTEM OPERATION
4.1 Arming Operation
To arm the alarm system, press Lock button on the transmitter:
•The siren will chirp once.
•The parking lights will flash once.*
•The doors will lock.*
•The LED will come on solid for 5 seconds, and then begin to flash. After 10
seconds the alarm system is armed.
*Optional feature
4.2 Remote Sensor Bypass
To arm the system and bypass the shock sensor, hood/trunk inputs, press the Lock
button to Arm, then within 2 seconds press the Lock button again. The siren will
chirp 5 times to indicate Sensor Bypass mode. The doors will still be monitored.
4.3 Passive Arming (Programmable feature)
The passive arming feature allows the system to arm automatically. The remote
transmitter still can be used to arm the system at any time. This option is user
programmable (see User Accessible Programming Options).
To arm the alarm system passively:
1. Turn the ignition Off.
2. Exit the vehicle and close all the doors.
•The LED will begin flashing rapidly to indicate the system is preparing to arm.
•The siren will chirp 30 seconds after the last door is closed to indicate the
system is armed.
•The doors will lock.*
*Optional feature
4.4 Disarming Operation
To disarm the system press the Unlock button on the transmitter:
•The siren will chirp twice.**
•The parking lights will flash twice.*
•The doors will unlock.*
•The dome light will turn on for 30 seconds.*
*Optional feature
** I f the alarm was triggered while away, the system will respond with 3 chirps
and 3 parking light flashes, see Tamper Alert.
MS2105 owner.qxd 8/25/2003 4:21 PM Page 6

7
4.5 Tamper Alert
On Disarming, if the system responds with three chirps, indicating the system was
triggered, turn on the ignition and the LED will flash the triggered zone 5 cycles.
LED Flashes (60 seconds):
1 flash = optional sensor
2 flashes = shock sensor
4 flashes = door
5 flashes = trunk
example: flash-flash-pause-flash-flash-pause = shock sensor
4.6 Silent Arming / Disarming (Programmable feature)
As an option, the system can be programmed to always Arm and Disarm the with or
without chirp confirmation (see User Accessible Programming Options).
To temporarily cancel the Arming and Disarming confirmation chirps, press the Level
Shift Button followed by the Arm or Disarm Button.
Note: The confirmation chirps will only be cancelled if the system status is normal. The
chirp indications for Tamper Alert and the open zone warning will not be cancelled when
the system is Armed or Disarmed silently.
4.7 Optional Driver's Door Priority Unlock
The optional Driver’s Door Priority Unlock feature provides a higher level of personal
safety by unlocking only the driver’s door upon disarming. Once disarmed, pressing the
disarm button again will unlock all doors. This optional feature may require additional
parts and labor, consult your Authorized Ungo dealer for more information.
4.8 Auto Rearm Feature (Programmable feature)
The Auto Rearm feature allows the system to automatically rearm itself in the event the
system becomes disarmed and a door is not opened within 30 seconds. This option is
user programmable (see User Selectable Programming Options).
4.9 Ignition Controlled Door Locks (Programmable feature)
The ignition door-locking feature allows the doors to automatically lock when the ignition
is turned On, and automatically Unlock when the ignition is turned Off.This option is user
programmable (see User Selectable Programming Options).
4.10 Remote Panic Feature
In the event of an emergency (PANIC) situation, the system's siren can be triggered for
45 seconds to attract attention. To activate the Panic feature, press and hold the Lock
button for 3 seconds.
MS2105 owner.qxd 8/25/2003 4:21 PM Page 7

8
•The siren will sound.
•The parking lights will flash.*
•The doors will unlock.*
•The starter disable will turn Off.*
*Optional feature
4.11 Coded Emergency Override (Programmable feature)
If the remote transmitter becomes lost or fails to operate, use the emergency override
feature to disarm the alarm system. Be sure that you have your ignition keys ready and
that you know the location of the Override switch before you perform this procedure.
To override the system:
1. Enter the vehicle.
•Because the alarm system is armed, the siren will sound.
2. Turn the ignition On.
3. Press the Override switch a number of times equal to the disarm code and continue
holding for 10 seconds on the last press. (If the default code setting has not been
changed, press and hold the override switch for 10 seconds to disarm to system.)
•The system will disarm.
•The siren will stop sounding.
•Starter disable will turn Off.
4. You can now start and drive the car.
5. If the disarm code is not entered correctly, turn off the ignition and begin again at
step 2.
6. Consult your authorized Ungo dealer to check the alarm system.
The default setting for the Emergency Override Disarm Code is 1. To change the
Emergency Override Code see User Selectable Programming Options, step 6.
Note: During installation, your installer can program the system to give a 15 second
entry delay when the system Arms passively. When the door is opened after the system
is Armed, the siren will give a series warning of chirps before sounding, giving you time
to perform the emergency override procedure.
4.12 Valet Mode
When placed into Valet Mode the security system will be disabled. However, the
optional keyless entry and auxiliary outputs will still function if installed.
To enter the Valet Mode:
1. Be sure the alarm system is disarmed.
2. Press and hold the Valet/Override button.
3. Turn the ignition On.
MS2105 owner.qxd 8/25/2003 4:21 PM Page 8

9
4. Continue holding the Valet/Override button for 3 seconds.
5. Turn the ignition Off.
•The siren will chirp once.
•The LED will turn On solid indicating the system is in Valet mode.
To exit Valet Mode:
1. Press and hold the Valet/Override button down.
2. Turn the ignition On.
3. Hold the Valet/Override button for 3 seconds.
4. Turn the ignition Off.
•The siren will chirp twice.
•The LED will turn off indicating the system is out of Valet mode.
4.13 Optional Trunk Release
Press the Trunk button for approximately 3 seconds to open the trunk. This optional
feature may require additional parts and labor, consult your Authorized Ungo dealer for
more information.
4.14 Optional Trunk Disarm Feature
The trunk disarm feature allows the alarm to disarm automatically when the Trunk
button is used to activate the optional trunk release. This eliminates having to disarm
the alarm system prior to activating the trunk release. This optional feature may require
additional parts and labor, consult your Authorized Ungo dealer for more information.
4.15 Programming 1-way (standard) Remote Transmitters
Make sure to have the desired transmitters ready and follow the steps below.
To program transmitters:
1. Turn the ignition ON.
2. Press and hold the Valet/Override switch for 5 seconds.
•The siren will chirp once.
3. Press the Lock button on the transmitter.
•The siren will chirp once.
4. Press the Lock button on the transmitter again.
•The siren will chirp twice.
5. Repeat steps 3 and 4 for each additional transmitter.
6. Turn OFF the ignition when transmitter programming is complete.
•The siren will chirp 3 times.
MS2105 owner.qxd 8/25/2003 4:21 PM Page 9

10
5. REMOTE START OPERATION
5.1 Remote Starting
To Remote Start the System:
1. Be sure the System is not in Valet Mode.
2. Press Button 4.
•The parking lights will turn on.
•The siren will chirp 3 times (if Armed, the shock sensor will turn off).
•The ignition will turn on.
•The engine will start and run for the duration of its programmed Run Timer.*
•The heater/air-conditioner will turn on (if turned on prior to exiting the vehicle).
•The LED will double flash.
*If the engine fails to start on the first attempt, it will repeat the starting procedure 2
more times.
Turning on the ignition key then pressing the brake pedal will disengage the MS2005
and allow you to operate and drive your vehicle in a normal manner.
5.2 Shut Down
Any of the following will shut down the engine when it is under Remote Start control:
1. Press Button 4 for 3 seconds.
• After the engine shuts down the doors will lock (if installed and programmed).
2. Press the brake pedal.
3. Open the hood (or trunk if connected).
4. Remote Start Time-Out (completion of the timed run cycle).
5.3 Stop and Go
The Stop and Go Feature allows you to remove the ignition key and exit the vehicle
while keeping the engine running during short stops.
To leave the vehicle running:
1. Press the brake pedal and hold.
2. While pressing the brake pedal, push Button 4 on the Remote Transmitter for 2
seconds.
• The LED will flash rapidly.
• The parking lights will flash 5 times.
3. Release the brake pedal.
4. Remove the key from the ignition switch.
5. You may now exit the vehicle, arm the alarm and lock the doors.
MS2105 owner.qxd 8/25/2003 4:21 PM Page 10