Clarion UNGO Pro Security S670 User manual

MMooddeellSS667700
➤
OOwwnneerr’’ssGGuuiiddee

i
© 2006 directed electronics, inc.
lliimmiitteeddlliiffeettiimmeeccoonnssuummeerrwwaarrrraannttyy
This Ungo Pro Security system is warranted against defects in material and workmanship.
The main unit is covered by this limited lifetime warranty. This Limited Lifetime
Warranty applies to Ungo Pro Security systems that have been installed by an authorized
Ungo Pro Security dealer. This warranty is to the Original Purchaser ("Owner") and to
the original vehicle in which it was installed into. This warranty is not transferable to any
subsequent owner(s) of the product(s).
WWaarrrraannttyyPPrrooggrraamm::
Main Unit Limited Lifetime
Remote Controls One year from date of purchase
Siren One year from date of purchase
Shock Sensor One year from date of purchase
LED One year from date of purchase
Override Switch One year from date of purchase
The Warranty does not cover batteries or products deemed damaged through alterations
or installation. It also does not cover products mishandled, misused, neglected, abused,
water damaged, or with removed/altered serial numbers.
PROOF OF PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE OF
THIS PRODUCT.
This warranty does not cover the costs incurred for removal or reinstallation of the main
unit and/or any damage to the vehicle or the vehicle's electrical system.
The sole responsibility of Clarion Corporation of America ("Clarion") under this
Warranty shall be limited to the repair or replacement of the product, at the sole discre-
tion of Clarion.
If it becomes necessary to send the product or any defective part to Clarion, the product
must be shipped in its original carton or equivalent carton, fully insured, with shipping
charges prepaid. Clarion will not assume any responsibility for any loss or damage
incurred in shipping.
ALL IMPLIED WARRANTIES EXCEPT TO THE EXTENT PROHIBITED BY
APPLICABLE LAW SHALL HAVE NO GREATER DURATION THAN THE
WARRANTY PERIOD SET FORTH ABOVE. UNDER NO CIRCUMSTANCES
SHALL CLARION CORPORATION BE LIABLE FOR ANY LOSS OR DAMAGE,
DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OR INABILITY
TO USE OF THE PRODUCT. BECAUSE SOME STATES DO NOT ALLOW LIMI-

ii © 2006 directed electronics, inc.
TATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSIONS
OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, THE
ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY
ALSO HAVE THE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.
Should you have any difficulties with the performance of this product during warranty,
please call: 1-800-GO-CLARION or visit your local Ungo Pro Security dealer. You may
also contact the National Service Manager at the following address below for additional
service help you may need.
Clarion Corporation of America
Attn: National Service Manager
661 W. Redondo Beach Blvd.
Gardena, Ca 90247

1
© 2006 directed electronics, inc.
ttaabblleeooffccoonntteennttss
lliimmiitteeddlliiffeettiimmeeccoonnssuummeerrwwaarrrraannttyy................................................................................ii
rreemmootteeccoonnffiigguurraattiioonnss................................................................
..................................22
LCD 2-way configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
standard 4-button configuration (both remotes) . . . . . . . . . . . . . . . . . . . . . . . . . 4
LCD 2-way remote additional controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
wwhhaattiissiinncclluuddeedd..............................................
..............................................................66
iimmppoorrttaannttiinnffoorrmmaattiioonn...............
...................................................................................77
system maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Standard LCD 2-way icon configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
LLCCDD22--wwaayyrreem
mootteeooppeerraattiioonn....................................................................................1155
system signal paging features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
uussiinnggyyoouurrssyysstteemm......................................................................................................1166
active arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
passive arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
warn away® response description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
triggered response description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
high security disarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
disarming without a remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
silent mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
panic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
valet mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
nuisance prevention® circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ddiiaaggnnoossttiiccss................................................................
..................................................2255
arming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
disarming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
system status chirps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
table of zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
ccooddeehhooppppiinngg.................................
.............................................................................2277
hhiigghhffrreeqquueennccyy......
......................................................................................................2288
rraappiiddrreessuummeellooggiicc.............................................................................
.........................2288
pprrooggrraammmmiinnggooppttiioonnss....................................................
............................................2299
iinnssttaallllaattiioonnooppttiioonnss.................................
...................................................................3311
gglloossssaarryyoofftteerrmmss.............
...........................................................................................3322

2© 2006 directed electronics, inc.
rreemmootteeccoonnffiigguurraattiioonnss
LCD 2-way configuration
1234
5
6
7
8
9
10
11
12
13
14
15
16
17 18
19
20
21
22
23
24
25
26
27
28
29
30
31
➜

3
© 2006 directed electronics, inc.
1 Vehicle Interior Temperature Indicator
2 Numeric Display
3 AM/PM Indicator
4 Alarm Clock Mode Indicator
5 Timer Function Indicator
6 Transmit Range Indicator
7 Transmission Indication
8 Vibrate/Beep Mode Indicator
9 Power Saver Mode Indicator
10 Remote Start Timer Mode Indicator
11 No Function
12 Vehicle Page Mode Indicator
13 Full Trigger Shock Sensor Indicator
14 Hood/Trunk Open or Trigger Indicator
15 Parking Light Indicator
16 Door Open or Trigger Indicator
17 Arm/Lock Button
18 Disarm/Unlock Button
19 Remote Start Indicator
20 Hood/Trunk Open or Trigger Indicator
21 Remote Start Button
22 Valet Mode Indicator
23 Remote Start Safety Shutdown Indicator
24 Battery Level Indicator
25 Auxiliary Button
26 Temperature-Controlled Remote Start Indicator
27 Silent Arm/Disarm Mode Indicator
28 Full Trigger Alert Indicator
29 Arm/Disarm Indicator
30 Function Button
31 Celsius/Fahrenheit Indicator

4© 2006 directed electronics, inc.
standard 4-button configuration (both remotes)
controls the Arm and Panic On/Off function. The arming
is controlled by pressing this button. The panic alarm is triggered
by pressing and holding this button. Press again to cancel the
panic alarm
controls the DDiissaarrmmand PPaanniiccOff function. Press this
button to disarm the system or to cancel the panic alarm.
controls SSiilleennttMMooddee™™and AAuuxxiilliiaarryychannel 22output.
Silent mode works by pressing this button for less than one
second before arming or disarming. And optional auxiliary func-
tion, such as trunk release, can be controlled by pressing and
holding this button for 1.5 seconds.
The auxiliary output controls __________________________.
controls the PPaanniiccfunction by pressing and holding this
button for 1.5 seconds.
and pressed together control channel 33output, and
optional auxiliary convenience or expansion function that you
have added to your system.
The auxiliary output controls __________________________.
➜

5
© 2006 directed electronics, inc.
and pressed together control channel 44output,
and optional auxiliary convenience or expansion function that
you have added to your system..
The auxiliary output controls __________________________.
LCD 2-way remote additional controls
The LCD backlighting will turn on when pressed for less
than one second; when held for more than five seconds the trans-
ceiver will enter adjustment mode allowing the setting of the
clock, timer mode, and audible melody selection. For more infor-
mation, please refer to the
Function Button Configurations
section of this guide.
and Buttons
The numeric display toggles between the time of the day and the
alarm clock when these buttons are pressed simultaneously.
and Buttons
Press these buttons simultaneously to activate the parking timer.
Each additional press will toggle through the available options
(10 min., 20 min., 30 min., 1 hour, 1.5 hours, 2 hours, and off).
note: The controls listed below are applicable only to the
LCD 2-way remote.
➜

6© 2006 directed electronics, inc.
and Buttons
When pressed simultaneously these buttons toggle between beep
notification and vibrate notification.
and Buttons
When pressed simultaneously these buttons activate battery
saver mode, which will drop power consumption on the trans-
ceiver battery to zero when the alarm is inactive or disarmed.
wwhhaattiissiinncclluuddeedd
➤Control module
➤544N transceiver/antenna
➤One 4-button remote
➤One 2-way LCD remote
➤Impact sensor on-board control module
➤High powered siren
➤Fault-proof starter interrupt relay on-board control module
➤Status LED indicator light
➤Push-button Valet button

7
© 2006 directed electronics, inc.
iimmppoorrttaannttiinnffoorrmmaattiioonn
Congratulations on the purchase of your state-of-the-art vehicle
security system. This system has been designed to provide years
of trouble-free operation. By carefully reading this guide prior to
using your system, you will maximize the use of this product and
its features.
By carefully reading this Owner's Guide prior to using your
system, you will maximize the use of this system and its features.
You can print additional or replacement copies of this manual by
accessing our web site at www.clarion.com.
system maintenance
The system requires no specific maintenance other than battery
replacement for the remotes.
LCD 2-Way Remote Battery Replacement
The 2-way remote is powered by a 1.5V AAA battery. The
Battery Level indicator has three level indicators that serve as a
visual indication of battery charge. When the battery reaches a
low charge level that requires replacement, the transceiver will
generate a single notification chirp, and the Battery Level indi-
cator will flash continuously.
➜

8© 2006 directed electronics, inc.
To replace the battery, gently pull the battery cover release tab, then
slide the door down to expose the battery and remove the expired
battery. Place the new battery into the transceiver observing the
correct polarity. When power is returned the transceiver will light
all icons in the LCD and generate a musical tone.
4-Button Remote Battery Replacement
Your remote is powered by a small, lightweight 3-volt lithium
battery (CR2032) that will last approximately one year under
normal use. When the battery begins to weaken, operating range
will be reduced and the LED on the remote will dim.
fcc/id notice
This device complies with Part 15 of FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesirable operation.
Tested to Comply
with FCC Standards
Directed Electronics, Inc. 544 Series
➜

9
© 2006 directed electronics, inc.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate this device.
Tested to Comply
with FCC Standards
Directed Electronics, Inc. 474V/ /S Series
Tested to Comply
with FCC Standards
Directed Electronics, Inc. 477T Series

10 © 2006 directed electronics, inc.
Standard LCD 2-way icon configuration
Icon
The vehicle interior temperature icon has no functions
Icon
The numeric display icon will show the hours and minutes.
Icon
The AM/PM icon indicates the time before or after noon.
Icon
The alarm clock mode icon indicates that the alarm clock mode
is active.
Icon
The timer function icon flashes during timed functions including
parking timer.
Icon
The transmit range indicator icon stays visible as long as the
system is within operating range.
Icon
The remote transmission indicator icon displays when the trans-
ceiver is transmitting a signal.
Icon
The vibrate/beep mode icon appears when the transceiver is set
to vibrate mode.
➜

11
© 2006 directed electronics, inc.
Icon
The power saver mode can be turned on or off with the trans-
ceiver. This icon displays the status.
Icon
The remote start timer mode icon has no function.
Icon
No function.
Icon
The vehicle page mode icon displays when the alarm module is
paging the transceiver.
Icon
The full trigger shock sensor icon indicates that the shock sensor
has been triggered by a hard shock.
and Icons
The hood/trunk open or trigger icon illuminates when the hood
or trunk trigger has been activated or the hood or trunk is open,
and bypasses those zones until it is closed.
Icon
The parking light icon will flash twice when armed or disarmed.
The icon also flashes during WarnAway.
Icon
The door open or trigger icon illuminates when the door trigger
has been activated or the door is open, and bypasses that zone
until it is closed.

12 © 2006 directed electronics, inc.
Icon
The remote start icon has no function.
Icon
The Valet mode icon appears when the system is in Valet mode.
Icon
The remote start safety shut down icon has no function.
Icon
The battery level icon indicates the level of power remaining in
the battery.
Icon
The temperature-controlled remote start icon has no function.
Icon
The silent arm/disarm icon appears when the system has been
armed or disarmed in the silent mode.
Icon
The full trigger alert icon illuminates when the security system
has been triggered by a heavy impact, door trigger violation,
optional sensor violation, or a hood/trunk trigger.
Icon
The arm icon appears when the vehicle is armed and locked. The
disarm icon appears when the vehicle is disarmed and unlocked.
Icon
Celsius/Fahrenheit icon indicates the current mode of the
displayed temperature either in Celsius or Fahrenheit.

13
© 2006 directed electronics, inc.
Standard LCD 2-way button functions
AAuuddiibbllee
FFuunnccttiioonnBBuuttttoonnIIccoonnIInnddiiccaattiioonn
Lamp On
(10 sec)
Power-Saver Mode* +Melody
Beep/Vibrate Mode +4 Vibrations/
1 Beep
Time Adjust for 5 Seconds 2 Beeps
Mode (hour)**
Time Adjust 1 Time***
Mode (min)**
Alarm Clock 2 Times***
Set Mode (hour)**
Alarm Clock 3 Times***
Set Mode (min)**
Alarm Clock Music 4 Times*** 5 Selections
or Power on Music 1/2/3/4/5
Selection**
Alarm Clock Adjust 5 Times***
Mode (on/off)**
Timer Count Down 6 Times***
Adjust Mode
(hour)**
Timer Count Down 7 Times***
Adjust Mode
(min)**
Timer Count 8 Times*** 5 Selections
Down Ending Melody 1/2/3/4/5
Selection 1**
RS Timer Count 9 Times***
Down Mode (on/off )* (where applicable)

14 © 2006 directed electronics, inc.
Remote Start On 10 times*** 5 Selections
Melody Selection 2 (where applicable) 1/2/3/4/5
10 Min Parking + 1 Time Melody
Count Down Mode
20 Min Parking + 2 Times Melody
Count Down Mode
30 Min Parking + 3 Times Melody
Count Down Mode
60 Min Parking + 4 Times Melody
Count Down Mode
90 Min Parking + 5 Times Melody
Count Down Mode
120 Min Parking + 6 Times Melody
Count Down Mode
Parking Count Down + 7 Times Melody
Off Mode
Alarm Clock Mode + Melody
On/Off****
Celsius/Fahrenheit + +
or
Melody
Select Mode
* This function will operate in the disarmed state only.
** The button will advance the selection upward. The but-
ton will advance the selection downward or select the off setting.
*** Be sure to hold down for five seconds prior to entering
timer clock adjust mode operation.
**** Press once to have the alarm clock on. Press twice to have the
alarm clock off.
The remote will revert to normal operation from the set mode
when 15-seconds has elapsed without a button entry.

15
© 2006 directed electronics, inc.
LLCCDD22--wwaayyrreemmootteeooppeerraattiioonn
The remote start system operates at 434 MHz and incorporates
Directed’s proprietary A.S.K. out-board two-way transceiver. The
high frequency combined with Binary Data communication
achieves superior range with two-way communication.
system signal paging features
A page is the signal the control module sends to the transceiver as
confirmation of receipt of a command or alarm system status.
When the transceiver receives a page it will generate a page notifi-
cation to the user (notifications are audible beeps or the remote
vibrates) and the LCD icons will display the current system status.
Command Page
When a command (arm/disarm, or auxiliary channel) from the
transceiver is sent and received, the system will send a command
page back to confirm receipt.
Page Recognition Mode
The transceiver will leave a zone icon illuminated when it has
received a triggered response and will wait for violation recogni-
tion. Press any button on the transceiver, the LCD information
and alarm page alerts will be cleared.
note: The transceiver buttons will not send a command
to the system until the alarm page is cleared.
➜

16 © 2006 directed electronics, inc.
uussiinnggyyoouurrssyysstteemm
active arming
You can arm the system by pressing of your remote for one
second. When the system arms, you will hear a short siren
sound, or chirp, and see the parking lights flash once. If the
power door locks are controlled by the system, the doors will
also lock. While the system is armed, the status LED will flash
approximately once per second, indicating that the system is
actively protecting your vehicle. If you hear a second chirp after
arming and note that the status LED is flashing in groups, see
the Diagnostics Section of this guide. This extra chirp is called
Bypass Notification, which indicates that a security sensor or
switch has been bypassed and the system is not monitoring that
area (zone) of the vehicle.
passive arming
The system can be programmed to arm itself automatically (called
passive arming). If the system is programmed for passive arming, it
will automatically arm 30 seconds after the ignition is turned off
and the last protected entry has been closed. (e.g. the system
detects that you have left the vehicle by opening and closing a
door.) Whenever the system is in its 30-second passive arming
countdown, the status LED will flash twice as fast as it does when
the system is armed. If the system is programmed for Passive
➜
➜
important: Due to the complexity of this system, instal-
lation of this product must only be performed by an
authorized Ungo dealer.

17
© 2006 directed electronics, inc.
Arming, care must be taken to prevent the keys from being
locked in the vehicle.
When armed your vehicle is protected as follows:
➤Light impacts trigger the Warn Away®signal. When triggered,
the siren chirps and the parking lights flash for a few seconds.
➤Heavy impacts trip a Triggered Sequence. The sequence
consists of the siren sounding continuously and the parking
lights flashing for 30 seconds.
➤If a door is opened, the system will immediately start
chirping the siren and flashing the parking lights. Three
seconds later, the siren output changes to a continuous blast.
This progressive response gives you time to disarm the sys-
tem with your remote if you inadvertently open the door
while the system is armed.
➤Turning on the ignition key will trip the same progressive
response as opening a door.
➤The starter kill prevents the vehicle’s starter from cranking.
warn away®response description
A Warn Away®Response consists of an alarm page along with
the responses described below.
➤SShhoocckkSSeennssoorr- Light impacts to the vehicle will flash the
vehicle lights and chirp the siren for a few seconds.
➜
note: If any protected entry point (such as a door or a
switch-protected trunk or hood) is open, the system will
not passively arm. Additionally, each time a protected
entry is opened (triggered) during the arming count-
down, the 30-second countdown starts over.