Clarion CZ201A User manual

Owner's manual & Installation manual
使用说明书&安装手册
사용설명서 및 설치설명서
CD/USB/MP3/WMA RECEIVER
CD/USB/MP3/WMA接收机
CD/USB/MP3/WMA 수신기

English
2
1. FEATURES........................................................................................................................3
Expanding Systems...........................................................................................................3
2. PRECAUTIONS .................................................................................................................4
Front Panel / Generalities..................................................................................................5
USB Port ...........................................................................................................................5
Remove the DCP ..............................................................................................................6
Attach the DCP..................................................................................................................6
3. CONTROLS .......................................................................................................................7
Operational Panel..............................................................................................................7
Names of Buttons..............................................................................................................7
Remote Control (RCX001:Sold by separately)..................................................................8
Notes of remote control using ...........................................................................................8
4. CAUTIONS ON HANDLING ..............................................................................................9
Handling Discs ..................................................................................................................9
5. OPERATIONS..................................................................................................................10
Basic Operations.............................................................................................................10
System Setup..................................................................................................................11
Audio Setup.....................................................................................................................12
Radio Operations ............................................................................................................12
CD/MP3/WMA Operations ..............................................................................................14
USB Operations ..............................................................................................................17
iPod & iPhone Operations...............................................................................................17
AUX Operations ..............................................................................................................18
6. TROUBLE SHOOTING....................................................................................................19
7. ERROR DISPLAYS..........................................................................................................20
8. SPECIFICATIONS ...........................................................................................................21
9. INSTALLATION / WIRE CONNECTION GUIDE.............................................................22
Thank you for purchasing this Clarion product.
• Please fully read this owner’s manual before operating this equipment.
• Check the contents of the enclosed warranty card and store it in a safe place with this manual.
Contents

3
English
1. FEATURES
Compatible with iPod ®/ iPhone®via USB
2ch/2V RCA Output with Subwoofer Control and BEAT-EQ with 3 Band Parametric
Equalizer
Detachable Front Panel with 3.5mm Auxiliary Input
MP3/WMA compatible with ID3-TAG display
2 Channel Amplier
Portable Player
(Connect via AUX IN Jack)
USB Memory
(Connect via CCA-755)
iPod/iPhone
(Connect via CCA-748)
Expanding Systems
Expanding audio features
Note:
• The items listed outside of the frames are the
commercial products generally sold.
• CCA-748 and CCA-755: Sold by separately.

English
4
2. PRECAUTIONS
For your safety, the driver should not operate the controls while driving.
Also, while driving, keep the volume to a level at which external sounds can be heard.
1. When the inside of the car is very cold and
the player is used soon after switching
on the heater, moisture may form on the
disc or the optical parts of the player and
proper playback may not be possible.
If moisture forms on the disc, wipe it off
with a soft cloth. If moisture forms on
the optical parts of the player, do not
use the player for about one hour. The
condensation will disappear naturally
allowing normal operation.
2. Driving on extremely bumpy roads which
cause severe vibration may cause the
sound to skip.
3. This unit uses a precision mechanism.
Even in the event that trouble arises,
never open the case, disassemble the
unit, or lubricate the rotating parts.
WARNING
CHINA
530-1710kHz 87.9-107.9MHz
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECTTO THE FOLLOWING TWO CONDITIONS:
(1)THIS DEVICE MAYNOT CAUSE HARMFULINTERFERENCE,AND
(2)THIS DEVICE MUST ACCEPTANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
THIS DEVICE COMPLIES WITH DHHS RULES 21 CFR CHAPTER I
SUBCHAPTER J APPLICABLEAT DATE OF MANUFACTURE.
CLARION CO.,LTD.
7-2,SHINTOSHIN,CHUO-KU,SAITAMA-SHI,SAITAMA-KEN,JAPAN
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
MANUFACTURED:
URF
PN:127070006874TX-1062B-A
65 mm
65 mm
CHINA
530-1710kHz 87.9-107.9MHz
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECTTO THE FOLLOWING TWO CONDITIONS:
(1)THIS DEVICE MAYNOT CAUSE HARMFULINTERFERENCE,AND
(2)THIS DEVICE MUST ACCEPTANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
THIS DEVICE COMPLIES WITH DHHS RULES 21 CFR CHAPTER I
SUBCHAPTER J APPLICABLEAT DATE OF MANUFACTURE.
CLARION CO.,LTD.
7-2,SHINTOSHIN,CHUO-KU,SAITAMA-SHI,SAITAMA-KEN,JAPAN
MANUFACTURED:
URF
PN:127070006834TX-1061B-A
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
65 mm
65 mm
65 mm
65 mm
CHINA
531-1602kHzMW
FM
LW 153-279kHz
87.5-108MHz
PN:127070006887TX-1072E-A
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
03 2120
CHINA
530-1710kHz 87.9-107.9MHz
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECTTO THE FOLLOWING TWO CONDITIONS:
(1)THIS DEVICE MAYNOT CAUSE HARMFULINTERFERENCE,AND
(2)THIS DEVICE MUST ACCEPTANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
THIS DEVICE COMPLIES WITH DHHS RULES 21 CFR CHAPTER I
SUBCHAPTER J APPLICABLEAT DATE OF MANUFACTURE.
CLARION CO.,LTD.
7-2,SHINTOSHIN,CHUO-KU,SAITAMA-SHI,SAITAMA-KEN,JAPAN
MANUFACTURED:
URF
PN:127070006827TX-1063B-A
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
65 mm
65 mm
65 mm
65 mm
CHINA
531-1602kHzMW
FM
LW 153-279kHz
87.5-108MHz
PN:127070006849TX-1074E-A
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
03 2120
65 mm
65 mm
CHINA
531-1602kHzMW
FM
LW 153-279kHz
87.5-108MHz
PN:127070006832TX-1072E-B
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
03 2120
65 mm
65 mm
CHINA
531-1602kHzMW
FM
LW 153-279kHz
87.5-108MHz
PN:127070006864TX-1072E-C
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
03 2120
65 mm
65 mm
531-1629kHz 87.5-108MHz
CHINA
PN:127070006890TX-1062K-A
051 722 877
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
65 mm
65 mm
531-1629kHz 87.5-108MHz
PN:127070006867TX-1062K-B
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
65 mm
65 mm
531-1629kHz 87.5-108MHz
CHINA
PN:127070006886TX-1061K-A
051 722 877
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
65 mm
65 mm
531-1629kHz 87.5-108MHz
PN:127070006857TX-1061K-B
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
65 mm
65 mm
CHINA
531-1602kHzMW
FM
LW 153-279kHz
87.5-108MHz
PN:127070006821TX-1073E-A
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
03 2120
65 mm
65 mm
CHINA
531-1602kHzMW
FM
LW 153-279kHz
87.5-108MHz
PN:127070006835TX-1073E-B
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
03 2120
65 mm
65 mm
CHINA
531-1602kHzMW
FM
LW 153-279kHz
87.5-108MHz
PN:127070006868TX-1073E-C
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
03 2120
CHINA
530-1710kHz 87.9-107.9MHz
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECTTO THE FOLLOWING TWO CONDITIONS:
(1)THIS DEVICE MAYNOT CAUSE HARMFULINTERFERENCE,AND
(2)THIS DEVICE MUST ACCEPTANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
THIS DEVICE COMPLIES WITH DHHS RULES 21 CFR CHAPTER I
SUBCHAPTER J APPLICABLEAT DATE OF MANUFACTURE.
CLARION CO.,LTD.
7-2,SHINTOSHIN,CHUO-KU,SAITAMA-SHI,SAITAMA-KEN,JAPAN
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
MANUFACTURED:
URF
PN:1270700XXXXXTX-10**B-A
65 mm
65 mm
CHINA
530-1710kHz 87.5-107.9MHz
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECTTO THE FOLLOWING TWO CONDITIONS:
(1)THIS DEVICE MAYNOT CAUSE HARMFULINTERFERENCE,AND
(2)THIS DEVICE MUST ACCEPTANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
THIS DEVICE COMPLIES WITH DHHS RULES 21 CFR CHAPTER I
SUBCHAPTER J APPLICABLEAT DATE OF MANUFACTURE.
CLARION CO.,LTD.
7-2,SHINTOSHIN,CHUO-KU,SAITAMA-SHI,SAITAMA-KEN,JAPAN
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
MANUFACTURED:
URF
PN:127070006889TX-10**B-A
65 mm
65 mm
65 mm
65 mm
CHINA
531-1602kHzMW
FM
LW 153-279kHz
87.5-108MHz
PN:12707000XXXXTX-10**E-A
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
03 2120
65 mm
65 mm
CHINA
531-1602kHzMW
FM
LW 153-279kHz
87.5-108MHz
PN:12707000XXXXTX-10**E-B
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
03 2120
65 mm
65 mm
CHINA
531-1602kHzMW
FM
LW 153-279kHz
87.5-108MHz
PN:12707000XXXXTX-10**E-C
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
03 2120
65 mm
65 mm
531-1629kHz 87.5-108MHz
CHINA
PN:12707000XXXXTX-10**K-A
051 722 877
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
65 mm
65 mm
531-1629kHz 87.5-108MHz
PN:12707000XXXXTX-10**K-B
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
CHINA
530-1710kHz 87.9-107.9MHz
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECTTO THE FOLLOWING TWO CONDITIONS:
(1)THIS DEVICE MAYNOT CAUSE HARMFULINTERFERENCE,AND
(2)THIS DEVICE MUST ACCEPTANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
THIS DEVICE COMPLIES WITH DHHS RULES 21 CFR CHAPTER I
SUBCHAPTER J APPLICABLEAT DATE OF MANUFACTURE.
CLARION CO.,LTD.
7-2,SHINTOSHIN,CHUO-KU,SAITAMA-SHI,SAITAMA-KEN,JAPAN
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
MANUFACTURED:
URF
PN:1270700XXXXXTX-10**B-A
65 mm
65 mm
65 mm
65 mm
CHINA
531-1602kHzMW
FM
LW 153-279kHz
87.5-108MHz
PN:12707000XXXXTX-10**E-A
This product includes technology owned by Microsoft Corporation and
cannot be used or distributed without a license from MSLGP.
03 2120

5
English
Front Panel / Generalities
For a longer service life, be sure to read the
following cautions.
• Do not allow any liquids on the set from
drinks, umbrellas, etc. Doing so may
damage the internal circuitry.
• Do not disassemble or modify the set in
any way. Doing so may result in damage.
• Do not let cigarettes burn the display.
Doing so may damage or deform the
body.
• If a problem should occur, have the set
inspected at your store of purchase.
• The remote control unit may not work if
the remote control sensor is exposed to
direct sunlight.
Cleaning the body
• Use a soft, dry cloth and gently wipe off
the dirt.
• For tough dirt, apply some neutral
detergent diluted in water to a soft cloth,
wipe off the dirt gently, then wipe again
with a dry cloth.
• Do not use benzene, thinner, car cleaner,
etc., as these substances may damage
the body or cause the paint to peel. Also,
leaving rubber or plastic products in
contact with the body for long periods of
time may cause stains.
About the registered Marks,etc.
“Made for iPod,” and “Made for iPhone”
mean that an electronic accessory has
been designed to connect specically to
iPod, or iPhone, respectively, and has
been certied by the developer to meet
Apple performance standards.
Apple is not responsible for the operation
of this device or its compliance with safety
and regulatory standards. Please note that
the use of this accessory with iPod or
iPhone may affect wireless performance.
iPhone and iPod are trademarks of Apple
Inc., registered in the U.S. and other
countries.
USB Port
• The USB memory stick may stick out
when inserted, so it may cause danger
during driving. When connect USB
memory stick to the main unit, please use
a USB extension cable (CCA-755).
• The USB memory sticks must be
recognized as “USB mass storage class“
to work properly. Some models may not
operate correctly.
When the memorized data is lost or
damaged by any chance, Clarion shall
not be liable for any damage.
When using an USB memory stick, we
recommend that you backup your data
stored on it before using a personal
computer etc.
• Data les may be broken when using USB
memory sticks in the following situation:
When disconnecting the USB memory
stick or turning the power off during
reading data.
When affected by static electricity or
electric noise.
Connect/disconnect the USB memory stick
when it is not accessed.
• Connecting with the computer is not
covered.

English
6
Remove the DCP
The control panel can be detached to prevent
theft. When detaching the control panel, keep
it in the safety place and prevent scratches.
W e r e c o m m e n d t a k i n g t h e D C P
(DETACHABLE CONTROL PANEL) with you
when leaving the car.
1. Press the [ SRC / ] button (1 sec.) to
turn off the power.
2. Deeply push in [OPEN] button to unlock
the DCP.
3. Hold the side popped out, remove the
DCP.
Attach the DCP
1. Hold the DCP and ensure that the panel
faces towards you. Set the right side of the
DCP into the DCP bracket.
2. Press the left side of the DCP until it locks.
CAUTION
• The DCP can easily be damaged by shocks. After removing it, be carefully not to drop it or
subject it to strong shocks.
• Once the [OPEN] button is pressed and DCP is unlocked, car vibrations can cause the DCP
to fall.
• The connector for the main unit and DCP is extremely important. Be careful not to damage it
by pressing on it with ngernails, screwdrivers, etc.
Note:
If the DCP is dirty, wipe off the dirt with a soft, dry cloth only.

7
English
3. CONTROLS
Operational Panel
[ SRC / ] Button
• Power / Toggle the audio source
[BAND] Button
• Select tuner band
[MENU] Button
• MP3/WMA mode – Search function.
• CD mode – No function.
• RADIO mode – No function.
• AUX mode – No function.
• USB mode – Search function
• iPod mode – iPod menu
[ ] Button
• Press to eject disc.
[ , ] Buttons
• Previous / next track
• Search (long press)
[Open] Button
• Unlock the front panel.
[PS / AS] Button
• Scan play / Preset scan
• Auto memory store (long press)
[SOUND] Button
• Sound effect setting
[VOLUME] Knob
• Adjust volume level / Conrm (press)
[ISR] Button
• Recall ISR station stored in memory and
store current station in ISR memory (long
press)
[1~6] Buttons
• [1] Button: Scan play / Preset station 1.
• [2] Button: Repeat play / Preset station 2.
• [3] Button: Random play / Preset station 3.
• [4] Button: Play / Pause / Top play (long
press) / Preset station 4.
• [5] Button: Previous folder / Preset station 5.
10 tracks down (long press)
• [6] Button: Next folder / Preset station 6.
10 tracks up (long press)
[ D ] Button
• Display switch
• System setup (long press)
Names of Buttons
[ , ] [OPEN]
[PS/AS]
[SOUND]
[VOLUME]
[ISR]
[1~6][BAND]
[MENU] [ ] USB ConnectorDisc Slot
AUX Jack
[ SRC / ] [ D ]

English
8
Remote Control (RCX001:Sold by separately)
Notes of remote control using
Inserting the Battery
1. Slide remote control unit’s rear cover in
the direction shown.
2. Insert battery (CR2025) into insertion
guides with printed side (+) up.
3. Press battery into compartment as shown.
4. Replace and slide cover until it clicks into
place.
1. Aim the remote control at the remote sensor
on the unit.
2. Remove the battery from the remote control
or insert a battery insulator if the battery has
not been used for a month or longer.
3. DO NOT store the remote control under
direct sunlight or in high temperature
environment, or it may not function properly.
4. Use “button shaped” lithium battery “CR2025”
(3V) only.
5.DO NOT subject battery to recharge,
disassemble, heat or dispose in re or water.
6.Insert the battery in proper direction
according to the (+) and (-) polarities.
7. Store the battery in a place where children
cannot reach to avoid the risk of accident.
Insertion guide
[SRC / ] Button
• Toggle the audio source
• Power on / Power off (long press)
[, ] Buttons
• Preset station up/down
• Previous / next track
• Search (long press)
[SCN/PS/AS] Button
• Scan play / Preset scan
• Auto memory store (long press)
[BAND/TOP] Button
• Select tuner band
• Top play (long press)
[ , ] Buttons
• Volume up / down
[ ] Button
• Play / Pause
[ISR] Button
• Recall ISR station stored in
memory
• Store current station in ISR
memory (long press)
[DISP] Button
• Display switch
[RDM] Button
• Random play
[RPT] Button
• Repeat play
[MUTE] Button
• Mute the volume
[ , ]
[ ]
[DISP]
[ISR]
[RDM]
[RPT]
[ , ]
[MUTE]
[SCN/
PS/AS]
[BAND/TOP]

9
English
Handling Discs
Handling
• New discs may have some roughness
around the edges. If such discs are used,
the player may not work or the sound
may skip. Use a ball-point pen or the like
to remove any roughness from the edge
of the disc.
• Never stick labels on the surface of the
disc or mark the surface with a pencil or
pen.
• Never play a disc with any cellophane
tape or other glue on it or with peeling off
marks. If you try to play such a disc, you
may not be able to get it back out of the
player or it may damage the player.
• Do not use discs that have large
scratches, are misshapen, cracked, etc.
Use of such discs may cause
misoperation or damage.
• To remove a disc from its storage case,
press down on the center of the case and
lift the disc out, holding it carefully by the
edges.
• Do not use commercially available disc
protection sheets or discs equipped with
stabilizers, etc. These may damage the
disc or cause breakdown of the internal
mechanism.
Storage
• Do not expose discs to direct sunlight or
any heat source.
• Do not expose discs to excess humidity
or dust.
• Do not expose discs to direct heat from
heaters.
Cleaning
• To remove ngermarks and dust, use a
soft cloth and wipe in a straight line from
the center of the disc to the
circumference.
• Do not use any solvents, such as
commercially available cleaners,
anti-static spray, or thinner to clean discs.
• After using special disc cleaner, let the
disc dry off well before playing it.
On Discs
• Never turn off the power and remove the
unit from the car with a disc loaded.
CAUTION
For your safety, the driver should not insert
or eject a disc while driving.
Ball-point pen
Roughness
4. CAUTIONS ON HANDLING

English
10
5. OPERATIONS
Basic Operations
Note:
• Refer to the diagrams in “3. CONTROLS”
when reading this chapter.
CAUTION
When the unit is turned on, starting and
stopping the engine with its volume
raised to the maximum level may harm
your hearings.
Be careful about adjusting the volume.
Power on / off
Notes:
• Start the engine before using this unit.
• Be careful about using this unit for a long
time without running the engine. If you
drain the car’s battery too far, you may not
be able to start the engine and this can
reduce the service life of the battery.
1. Start the engine. The power button / knob
illumination on the unit will light up.
Engine ON
position
2. Press the [SRC / ] button on the front
panel or the remote control to turn on the
power under standby mode. The unit goes
back to the last status after power on.
3. Press and hold the [SRC / ] button on
the front panel or the remote control to
turn off the power.
Mute
Press the [MUTE] button on the remote
control to mute the volume from the unit.
Note:
Doing the operation above again or adjusting
volume will release muting.
Volume adjustment
Turn the [VOLUME] knob on the front panel
or press the [ ]or [ ] button on the
remote control.
The adjustable range of volume is 0 to 40.
CAUTION
While driving, keep the volume level at
which external sounds can be heard.
Playing source selection
Press [SRC / ] button on the front panel
and remote control repeatedly to choose
desired playing source.
Notes:
• Playing source selection means selecting
work mode, such as DISC mode, RADIO
mode, AUX mode, etc.
Display system time
Press the [ D ] button on the front panel or
[DISP] button on the remote control to switch
the display information, system time and
playing source.
RESET
Note:
* When the [RESET] button is pressed,
frequencies of radio stations, titles, etc.
stored in memory are cleared.
RESET

11
English
At all mode, press and hold [ D ] button to
enter system setup. Press [ ] or [ ] button
to select options, rotate the [VOLUME] knob
to adjust.
CLOCK
Press the [VOLUME] knob to enter clock
setting mode, Rotate the [VOLUME] knob
to set clock, press [ ] or [ ] button to
select hour or minute, press and hold the
[VOLUME] knob to conrm.
DX/LO (RADIO mode)
Rotate the [VOLUME] knob to choose radio
local or distant at RADIO mode.
• LO: Only stations with strong signal can
be received.
• DX: Stations with strong and weak signals
can be received.
AUX SENS (AUX mode)
Rotate the [VOLUME] knob to choose AUXInput
sensitivityLOW,MIDorHIGHatAUX mode.
SCRN SVR: ON/OFF
Rotate the [VOLUME] knob to choose SCRN
SVR (screen saver) ON or OFF.
SCROLL: ON/OFF
For track information that is longer than the
display panel:
When SCROLL is ON, the LCD will display
ID3 TAG information cyclely, e.g: FILE-
>FOLDER->TITLE->ARTIST->ALBUM-
>TRACK->FILE...
When SCROLL is OFF, the LCD will display
one of the ID3 TAG information, the default
is TRACK, but user can adjust it to other ID3
TAG information by press [D]button.
System Setup
S-CTRL (IPOD mode) : ON/OFF
Rotate the [VOLUME] knob to choose S-CTRL
(Simple control) ON or OFF.
* Refer to P18.
DIMMER: ON/OFF
Rotate the [VOLUME] knob to choose
DIMMER ON or OFF.
• ON: LCD dimmer is active when small light
of vehicle is turned ON.
• OFF: LCD always maximum brightness
regardless of the vehicle small light.
REAR/S-W
Rotate the [VOLUME] knob to choose REAR
or S-WOOFER (SUB-WOOFER).
TEL-SW
Rotate the [VOLUME] knob to choose OFF,
MUTE or ON .
• OFF:
This unit continues normal operation even
when the cellular phone is used.
• MUTE:
The sound from this unit is muted during
telephone calls.
• ON:
You can listen to your telephone calls from
the speakers connected to this unit.
*When listening to your calls on your car
speakers, you can adjust the volume by
turning the [VOLUME] knob.
BEEP: ON/OFF
Rotate the [VOLUME] knob to choose button
beep sound ON or OFF.
12/24H
Rotate the [VOLUME] knob to choose
time format: 12 or 24 hour.

English
12
Select tuner as playing source
Press [SRC / ] button once or more to
enter RADIO mode.
Select one radio band
Press the [BAND] button on the panel or
[BAND/TOP] button on the remote control
to select one radio band among FM1, FM2,
FM3 and AM.
Manual tuning
During manual tuning, the frequency will be
changed in steps.
Press the [ ] or [ ] button on the
panel to tune in a higher / lower station.
Press the [ ] or [ ] button on the
remote control to tune in preset stations.
Auto tuning
Press and hold the [ ] or [ ] button
to seek a higher / lower station.
To stop searching, repeat the operation
above or press other buttons having radio
functions.
Radio Operations
Note:
When a station is received, searching stops
and the station is played.
Preset scan
Preset scan receives the stations stored
in preset memory in order. This function is
useful when searching for a desired station in
memory.
1. Press the [PS/AS] button.
2. When a desired station is tuned in, press
the [PS/AS] button again to continue
receiving that station.
Note:
Be careful not to press and hold the [PS/AS]
button for 1 second or longer, otherwise the
auto store function is engaged and the unit
starts storing stations.
Press the [SOUND] button to enter sound
effect setting mode. First press shows current
EQ. Rotate the [VOLUME] knob to changes
BEAT EQ in this order:
OFF -> B-BOOST -> IMPACT -> EXCITE ->
CUSTOM
Rotate the [VOLUME] knob to changes
CUSTOM, and press the [VOLUME] knob,
the press [ ] or [ ] button to select
it including: BAS-G -> BAS-F -> BAS-Q
-> MID-G -> MID-F -> MID-Q -> TRE-G ->
TRE-F, rotate the [VOLUME] knob to select a
value.
BAS-G / MID-G / TRE-G: (-7)- (+7)
BAS-F: 60 / 80 / 100 / 200
BAS-Q: 1.0 / 1.25 / 1.5 / 2.0
Audio Setup
MID-F: 500 / 1K / 1.5K / 2.5K
MID-Q: 0.5 / 0.75 / 1.00 / 1.25
TRE-F: 10.0K / 12.5K / 15.0K / 17.5K
Press the [SOUND] button, then press [ ] or
[ ] button to select USER preset
including:
BALANCE -> FADER -> M-B EX -> LPF (low
pass lter) -> S-W VOL (Subwoofer Volume),
rotate the [VOLUME] knob to select a value.
BALANCE: LEFT 1-7->CENTER->RIGHT 1-7
FADER: FRONT 1-7->CENTER->REAR 1-7
M-BEX: ON/OFF
LPF: THROUGH / 80 / 120 / 160
SUBW VOL: (-6)- (+6)

13
English
Radio Operations
Auto store
Only stations with sufcient signal strength
will be detected and stored in the memory.
Press and hold the [PS/AS] button (1 sec.) to
start automatic station .
To stop auto store, press other buttons
having radio functions.
Notes:
1. After auto store, the previous stored
stations will be overwritten.
2. The unit has 4 bands, such as FM1, FM2,
FM3 and AM. FM3 and AM can store
by AS function. Each bands can store 6
stations, CZ201A can store 24 stations in
total.
Manual store
When one expected radio station has
been detected, press and hold number
button 1-6 to store it in the memory.
Recall the stored stations
Press one numeric button among
1 to 6 on the panel to select the
corresponding stored station.
Local seeking
When LOCAL seeking is on, only those
radio stations with strong radio signal
could be received.
To open or close LOCAL function,
press and hold the [D]button on the
front panel, then press [ ] button
repeatedly until LO or DX displays on
the screen, and rotate the [VOLUME]
knob to select Local or Distant mode.
Note:
The number of radio stations that can
be received will decrease after the local
seeking mode is on.

English
14
Folder structure
A disc with a folder having more than 8
hierarchical levels will be impossible.
Number of les or folders
1. Up to 999 files can be recognized per
folder.
Up to 3000 les can be played.
2. Tracks are played in the order that they
were recorded onto a disc. (Tracks may
not always be played in the order displayed
on the PC.)
3. Some noise may occur depending on
the type of encoder software used while
recording.
Eject function
Just pressing the [ ] button, ejects the disc
even if the power to the unit was not turned
on.
Notes:
• If you force a CD into before auto
reloading, this can damage the CD.
• If a CD (12 cm) is left ejected for 15
seconds, the CD is automatically reloaded
(Auto reload).
Listening to a disc already loaded
in the unit
Press the [SRC / ] button to select the CD/
MP3/WMA mode.
When the unit enters the CD/MP3/WMA
mode, play starts automatically.
Loading a CD
Insert a CD into the center of the CD
SLOT with label facing up. The CD plays
automatically after loading.
Notes:
• Never insert foreign objects into the CD
SLOT.
• If the CD is not inserted easily, there may
be another CD in the mechanism or the
unit may require service.
• Discs without the or
TEXT
mark and
CD-ROMs cannot be played by this unit.
• Some CD-R/CD-RW discs may not be
usable.
This unit can play back MP3/WMA
les
Notes:
• If you play a WMA file with active DRM
(Digital Rights Management), no audio is
output.
To disable DRM (Digital Rights Management)
When using Windows Media Player 9/10/11,
click on Tool -> Options -> Copy Music tab,
then under Copy Settings, unclick the Check
box for Copy Project Music. Then, reconstruct
les.
Personally constructed WMA files are used
at your own responsibility.
Precautions when creating MP3/
WMA le
Usable sampling rates and bit rates
1. MP3: Sampling rate 8 kHz-48 kHz, Bit rate
8 kbps-320 kbps / VBR
2. WMA: Bit rate 8 kbps-320 kbps
File extensions
1. Always add a le extension “.MP3”, “.WMA”
to MP3, WMA file by using single byte
letters. If you add a file extension other
than specified or forget to add the file
extension, the le cannot be played.
2. Files without MP3/WMA data will not play.
The files will be played soundlessly if you
attempt to play les without MP3/WMA data.
* When VBR les are played, the play time
display may differ the play location.
* When MP3/WMA les are played, a little
no sound part is caused between tunes.
Logical format (File system)
1. When writing MP3/WMA file on a CD-R
disc or CD-RW disc, please select
“ISO9660 level 1, 2 or Joliet or Romeo” or
Apple ISO as the writing software format.
Normal play may not be possible if the disc
is recorded on another format.
2. The folder name and file name can be
displayed as the title during MP3/WMA play
but the title must be within 32 single byte
alphabetical letters and numerals (including
an extension).
3. Do not afx a name to a le inside a folder
having the same name.
CD/MP3/WMA Operations

15
English
CD/MP3/WMA Operations
Pausing play
1. Press the [ 4 ] button to pause play.
“PAUSE” appears in the display.
2. To resume CD play, press the [4]button
again.
Displaying CD titles
This unit can display title data for MP3/WMA
disc.
When SCROLL is OFF, each time you press
the [D]button to change the title display.
MP3/WMA disc
FILE->FOLDER->TITLE->ARTIST->ALBUM-
>TRACK->FILE ...
Notes:
• If MP3/WMA disc is not input TAG, “NO
TITLE” appears in the display.
• Only ASCII characters can be displayed in
Tags.
Selecting a track
Track-up
1. Press the [ ] button to move to the
beginning of the next track.
2. Each time you press the [ ] button, the
track advances to the beginning of the
next track.
3. For MP3/WMA disc, press and hold the
[6]button (1 sec.) to move ahead to +10
tracks.
Track-down
1. Press the [ ] button to move back to
the beginning of the current track.
2. Press the [ ] button twice to move back
to the beginning of the previous track.
3. For MP3/WMA disc, press and hold the
[ 5 ] button (1 sec.) to move back to -10
tracks.
Fast-forward/Fast-reverse
Fast-forward
Press and hold the [ ] button .
Fast-reverse
Press and hold the [ ] button .
* For MP3/WMA discs, it takes some time
until the start of searching and between
tracks. In addition, some errors may occur
in the play time.
Folder Select
This function allows you to select a folder
containing MP3/WMA les and start playing
from the rst track in the folder.
1. Press the [5]or [6]button.
Press the [6]button to move the next
folder. Press the [ 5 ] button to move the
previous folder.
2. To select a track, press the [ ] or [ ]
button.
Search Function
1. Press the [MENU] button to enter FOLD
SCH mode. Press the [VOLUME] button
to enter the folder list search mode.
2. Turn the [VOLUME] knob to select a folder.
3. Press the [VOLUME] button to enter the
file list search mode. And then the track
list appears in the display.
4. Turn the [VOLUME] knob to select a track.
5. Press the [VOLUME] knob to play.
* When play back MP3 / WMA file, this
function is performed in the current folder.
Top function
The top function resets the CD player to the
rst track of the disc. Press and hold the [ 4 ]
button (1 sec.) to play the first track (track
No. 1) on the disc.
* In case of MP3/WMA, the rst track of the
current folder will be played.

English
16
Other various play functions
Scan play
This function allows you to locate and play
the rst 10 seconds of all the tracks recorded
on a disc.
Press the [1]button to perform scan play.
Repeat play
This function allows you to play the current
track repeatedly or play a track currently
being played in the MP3/WMA folder
repeatedly.
CD:
1. Press the [ 2 ] button once or more until
“RPT ON” appears on the LCD to perform
repeat play.
2. Press [2]button repeatedly until “RPT
OFF” appears on the LCD to cancel repeat
playback.
MP3/WMA:
1. Press the [2 ]button once or more until
“TRACK RPT” appears on the display to
perform repeat play, and “RPT” segment
lights on.
2. For MP3/WMA files, press [2 ]button
repeatedly until “FOLD RPT” appears on
the display for folder repeat play.
3. Press [2 ]button repeatedly until “RPT
OFF” appears on the display to cancel
repeat playback, and “RPT” segment goes
o.
CD/MP3/WMA Operations
Random play
This function allows you to play all tracks
recorded on a disc in a random order.
Press the [3]button to perform random play.
Random function activates when jumping to
another track.

17
English
1. Open the cover of the USB connector to the
right. Insert a USB cable (CCA-755) into
the USB connector. Insert a USB device
into the USB cable.
When connecting a USB device, the unit
will read the les automatically.
2. To remove the USB device, you should rst
select another source or turn off the power,
in order to avoid damaging the USB device.
Then take off the USB device. Close the
cover to the left.
3. Operation is same as MP3/WMA operation.
USB Operations
iPod & iPhone Operations
Connect
Connect an iPod or iPhone to the USB
connector via CCA-748 cable.
When connecting a device, the unit will read
the files automatically. The track information
display on the screen once playback start.
MENU
In the S-CTRL OFF mode, press [MENU]
button,rotate the [VOLUME] knob select
“MUSIC” or “VIDEO”.
Select “MUSIC”, press the [VOLUME] knob,
then rotate the [VOLUME] knob to show PLAY
LISTS / ARTISTS / ALBUMS / GENRES /
SONGS / COMPOSERS, press and rotate the
[VOLUME] knob to select a desired option,
then press the [VOLUME] knob to conrm.
Select “VIDEO”, press the [VOLUME]
knob, then rotate the [VOLUME] knob to
show MOVIES MUSIC VIDEO / TV SHOWS
VIDEO PODCASTS / RENTALS, press and
rotate the [VOLUME] knob to select a desired
option, then press the [VOLUME] knob to
conrm.
NOTE:
VIDEO MENU item is different by the model of
connected iPod and language setting.
Repeat play
This function allows you to play the current
track repeatedly or play all tracks in your
iPod/iPhone repeatedly.
1. Press the [ 2 ] button once or more until
“RPT ON” appears on the LCD to perform
repeat play.
2. Press [2]button repeatedly until “RPT
OFF” appears on the LCD to cancel repeat
playback.
Random play
This function allows you to play all tracks
recorded on a disc in a random order.
1. Press [ 3 ] button repeatedly until “ALBUM
RDM” appears on the LCD for album
random play.
to monitor
CCA-755
CCA-748

English
18
iPod & iPhone Operations
Press [ SRC / ] button on the panel or
remote control to select “AUX”.
AUX is just for audio content with 3.5mm
Jack connector plugged into audio-in socket
on the front panel.
AUX Input sensitivity setting
1. Press and hold the [ D ] button (1 sec.).
2. Turn the [VOLUME] knob to select “AUX
SENS”.
AUX Operations
2. Press the [ 3 ] button once or more until
“SONG RDM” appears on the LCD to
perform random play.
3. Press [ 3 ] button repeatedly until “RDM
OFF” appears on the LCD to cancel
random playback.
Setting iPod simple control mode
Use this function if you wish to operate
through your iPod connected to this unit via
the USB cable.
* The factory default setting is “ OFF “.
1. Press and hold [ D ] button to enter system
setup.
2 Press [ ] or [ ] button to select
“ S-CTRL“.
3. Rotate the [VOLUME] knob to select
“ ON “ or “ OFF “ .
• ON: Operations are made through your
iPod.
• OFF: Operations cannot be made
through your iPod.
Notes:
• When performing iPod operations using
simple control mode, make the operations
slowly. If repetitive operations are
performed too quickly, Unforeseen errors
may occur.
• When performing iPod operations using
simple control mode, please do not
operate the iPod and the unit at the same
time, otherwise there may be unexpected
event happened.
• Some iPod models do not support this
function. Consult your nearest Clarion
dealer or website to conrm which models
do not support this function.
iPod menu alphabet search
This function searches the subfolders for
desired alphabetical letters.
1. Press the [MENU] button to select the iPod
menu mode.
2. Press the [VOLUME] knob to switch
between categories.
MUSIC: PLAYLIST, ARTISTS, ALBUMS,
GENRES, SONGS, COMPOSERS
VIDEO: MOVIES, MUSIC VIDEOS, TV
SHOWS VIDEO
PODCASTS, RENTALS
3. Press the [VOLUME] knob. (The contents
of the category are displayed.)
4. Press and hold the [ D ] button (1 sec.).
5. Rotate the [VOLUME] knob to select the
desired letter to search.
6. Press the [ D ] button again to next perform
search.
3. If the output level of connected external
audio player is “HIGH”, rotate [VOLUME]
knob and choose “LOW”. And if the output
level is “LOW”, choose “HIGH”.

19
English
6. TROUBLE SHOOTING
GENERAL
Problem Cause Measure
Unit can not power
on.
Unit fuse blown. Replace with new fuse of correct rating.
Car battery fuse blown. Replace with new fuse of correct rating.
Unit can not
power on.Nothing
happens when
buttons are
pressed.
Display is not
accurate.
The microprocessor has
malfunctioned due to noise, etc.
Turn o the power and remove the DCP.
Press the [RESET] button with a thin rod.
Note:
When the [RESET] button is pressed, turn o
the ACC power.*
* When the [RESET] button is pressed,
frequencies of radio stations, titles, etc. stored in
memory are cleared.
Remote control
does not work
Battery depleted. Change the battery.
Battery installed incorrectly. Install the battery correctly.
No/low audio
output.
Improper audio output connection. Check wiring and correct.
Volume set too low. Increase volume level.
Speakers damaged. Replace speakers.
Heavily biased volume balance. Adjust the channel balance to center position.
Speaker wiring is in contact with
metal part of car. Insulate all speaker wiring connections.
Poor sound quality
or distortion
Non-standard disc used. Use a standard disc.
Speaker power rating does not
match unit. Replace speakers.
Wrong connections. Check wiring and correct.
Speaker is shorted. Check wiring and correct.
Tel-Mute
malfunction MUTE wire is grounded. Check the MUTE wiring and correct.
Unit resets itself
when engine is off.
Incorrect connection between ACC
and Battery. Check wiring and correct.

English
20
7. ERROR DISPLAYS
Display Cause Measure
ERROR 3 Disc is inserted incorrectly. Eject the disc then reload it properly.
The disc format is not supported. Try another disc.
ERROR 5 This is a failure of deck’s mechanism. Consult your store of purchase.
If an error occurs, one of the following displays is displayed.
Take the measures described below to solve the problem.
If an error display other than the ones described above appears, press the [RESET] button. If
the problem persists, turn off the power and consult your store of purchase.
* When the [RESET] button is pressed, frequencies of radio stations, titles, etc. stored in
memory are cleared.
USB Devices
Problem Cause Measure
USB device cannot
be inserted.
The USB device has been
inserted with wrong direction.
Reversing the connection direction of the USB
device, try it again.
The USB connector is broken. Replace with a new USB device.
USB device is not
recognized.
The USB device is damaged. Disconnect the USB device and reconnect. If the
device is still not recognized, try replacing with a
different USB device.
Connectors are loose.
No sound heard with
the display “No File”
shown.
No MP3/WMA le is stored in the
USB device. Store these les properly in the USB device.
Sound skips or is
noisy. MP3/WMA les are not encoded properly. Use MP3/WMA les encoded properly.
DISC Player
Problem Cause Measure
Disc cannot be
loaded.
Another disc is already loaded. Eject the disc before loading the new one.
There is an object installed inside the
unit. Remove the object inside the unit.
Sound skips or is
noisy.
Compact disc is dirty. Clean the compact disc with a soft cloth.
Compact disc is heavily scratched or
warped.
Replace with a compact disc with no
scratches.
Sound is bad when
power is rst turned
on.
Condensation may form on the internal
lens when the car is parked in a humid
place. Let dry for about 1 hour with power on.