Claro INFINITY 401 User manual

Quick
Installation
Guide
For INFINITY 401
Package Contents
Power Adapter x1
(12V/2A )
RJ-45 Cable x1INFINITY401 x1QIG x1

INFINITY 401 DOCSIS/EURODOCSIS 3.0 Cable Modem Quick Installation Guide
1
WLAN 2.4GHz
Front Panel & LEDs
There are Light-Emitting-Diodes (LEDs) located on the front panel to indicate the status information of cable modem.
NAME
TEL2/TEL1 Green
WPS
Blinking
On
Off
WPS in paring
WPS enabled
WPS disabled
Blue
WLAN 5GHz
On
Off
Blinking
Wi-Fi enable
Wi-Fi disable
Data in traffic
On
Off
Blinking
TEL on-hook
TEL disable
TEL provisioning or off-hook
Green
On
Off
Blinking
Wi-Fi enable
Wi-Fi disable
Data in traffic
Green
LAN
Blinking
On
Off
Data in traffic
ETH device connected (GbE mode)
No ETH device connected
Green
ONLINE
Blinking
On
Off
Data in traffic
ETH device connected (FE mode)
No ETH device connected
Orange
Blinking
On
Off
CM provisioning
CM On-line
CM Off-line
Green
PWR
On
Off
DC Power is connected
No DC Power connected
Green
COLOR MODE STATUS
Blinking
On
Off
Downstream scanning
Downstream locked
Cable interface idle or W/DS bonding
Blue
On
Off
W/DS locked
W/DS disabled
Green
DS
Blinking
On
Off
Upstream scanning
Upstream locked
Cable interface idle or W/US bonding
Blue
On
Off
W/US locked
W/US disabled
Green
US

INFINITY 401 DOCSIS/EURODOCSIS 3.0 Cable Modem Quick Installation Guide
2
Rear Panel and Hardware Connection
The following describes the proper steps for connecting your cable modem. Please be sure to follow the steps in the sequence outlined below.
Failure to do so could result in improper operation or failure of your cable modem.
Step 1: Connect a cable by feeding the F-connector on the back of the
cable modem. Ensure the center conductor of the 75 ohm coaxial
cable is inserted directly into the center of the F-connector. Secure
the coaxial cable by carefully threading the outer shell of the coaxial
cable connector onto the F-connector in a clockwise direction until
tight. Be careful not to over-tighten the connector or you may damage
either the connector or the cable modem.
Step 2: Connect the cable modem to an IEEE 802.3 10Base-T / 802.3u 100
Base-TX / 802.3ab 1000Base-T Network using a RJ-45 male-terminated
Ethernet cable. This cable modem equips with four Ethernet ports, you
can connect two PCs to the cable modem at the same time if necessary.
Step 3: Connect the telephone sets to TEL1 and TEL2. Use RJ-11 telephone
line to connect TEL1/TEL2 port on the cable modem and telephone
socket on telephone.
Step 4: Connect the AC Adapter to the cable modem by inserting the barrel-
shaped connector into the mating power connector on the back of the
cable modem. Exercise carefully to ensure the connectors are properly
aligned prior to insertion and ensure the two connectors engage
completely. The cable modem is shipped with an AC adapter. Remember
to use only power adapter that came with the cable modem. Other power
adapters might have voltages that are not correct for your particular cable
modem. Using a power adapter with the wrong voltage can damage the
cable modem.
Step 3
Connecting the
Telephone cord
Step 1
Connecting the
Coaxial Cable
Step 4
Connecting to
the AC Adapter
Step 2
Connecting the
Ethernet Cord

INFINITY 401 DOCSIS/EURODOCSIS 3.0 Cable Modem Quick Installation Guide
3
Accessing the Web Management
For easy-changing the default settings, a Web-based GUI is built-in for your access.
Use the following procedures to login to your INFINITY 401 .
1. Open your web browser.
2. Type the default IP address of the INFINITY 401 (http://192.168.20.1) and press Enter.
3. The Log In page appears. Type the user name (admin) and your password (password) in the respective fields.
Configuring Your WAN Connection
The DHCP page allows you to activate/deactivate the DHCP server function of the INFINITY 401 , and, if the DHCP
server is activated, to see DHCP leases it has provided.

INFINITY 401 DOCSIS/EURODOCSIS 3.0 Cable Modem Quick Installation Guide
4
Check your INFINITY 401 Access Information
There is a label pasted to the bottom of INFINITY 401 case. In that label, you can obtain following information. Please note, following label is just
an example, each INFINITY 401 has their own label and setting value. Please follow your label information to access and configure INFINITY 401.
In normal case, you don’t need to change anything, all setting have been set and work properly.
SSID: This is used for your INFINITY 401 wireless setting use, and, this setting has already been set to your INFINITY 401.
WPA Pre-Shared Key: This is the password for your wireless client when connecting to INFINITY 401. You will be asked
to key in this password so as to connect via wireless connection.Web Management: This is the
URL when you like to access to INFINITY 401. You can simply type http://192.168.20.1 in Microsoft
Internet Explorer or any other internet browser to access INFINITY 401 web management page.
Login: This is the value when accessing INFINITY 401 web management page. You will be asked to key in this default value
to access INFINITY 401.
Password: This is the value when accessing INFINITY 401 web management page. You will be asked to key in this default
value to access INFINITY 401.
This document is subject to change without notice 7MN-I384G1-XXXR

INFINITY 401 DOCSIS/EURODOCSIS 3.0 Cable Modem Quick Installation Guide
5
Note to CATV Sysrem Installer
"The EUT must be bonding the screen of the coaxial cable to the earth at the building entrance per ANSI/NFPA 70, the National Electrical Code (NEC),
in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable.”
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority
to operate this equipment.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body
FCC RF Radiation Exposure Statement:
This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

INFINITY 401 DOCSIS/EURODOCSIS 3.0 Cable Modem Quick Installation Guide
6
FCC Statement
This device complies with Class B Part 15 of the FCC Rules. The device generates, uses and can radiate radio frequency energy and, if not installed and
used as instructed, may cause harmful interference to radio communication. Only Coaxial cables are to be used with this device in order to ensure
compliance with FCC emissions limits. Accessories connected to this device by the user must comply with FCC Class B limits. The manufacturer is not
responsible for any interference which results from use of improper cables, or which results from unauthorized changes or modifications to the device.
"A Minimum 26 AWG Line Core should be used for connection to the cable modem" this device may not cause interference and this device must accept
any interference, including interference that may cause undesired operation of the device.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment with IC radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with IC RF exposure compliance
requirements, please follow operation instruction as documented in this manual.
Warranty
Items sold by manufacturer/distributor/agent, hereinafter called "Seller", are warranted only as follows: Except as noted below Seller will correct, either by
repair or replacement at its option, any defect of material or workmanship which develops within one year after delivery of the item to the original Buyer
provided that evaluation and inspection by Seller discloses that such defect developed under normal and proper use. Repaired or replaced items will be
further warranted for the unexpired term of their original warranty. All items claimed defective must be returned to Seller, transportation charges prepaid,
and will be returned to the Buyer with transportation charges collect unless evaluation proves the item to be defective and that the Seller is responsible for
the defect. In that case, Seller will return to Buyer with transportation charge prepaid. Seller may elect to evaluate and repair defective items at the Buyer's
site. Seller may charge Buyer a fee (including travel expenses, if needed) to cover the cost of evaluation if the evaluation shows that the items are not
defective or that they are defective for reasons beyond the scope of this warranty.
The Seller makes no warranty concerning components or accessories not manufactured by it. However, in the event of failure of such a part, Seller will give
reasonable assistance to Buyer in obtaining from the manufacturer whatever adjustment is reasonable in light of the manufacturer's own warranty. Seller will
not assume expense or liability for repairs made outside the factory by other than Seller's employees without Seller's written consent.
SELLER IS NOT RESPONSIBLE FOR DAMAGE TO ANY ASSOCIATED EQUIPMENT, NOR WILL SELLER BE HELD LIABLE FOR INCIDENTAL,
CONSEQUENTIAL, OR OTHER DAMAGES. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING
THE IMPLIED WARRANTY OF "MERCHANTABILITY" AND "FITNESS FOR PARTICULAR PURPOSE."
Trademarks
All trademarks are the property of their respective owners.