Classic Exhibits gravitee GK-2010 Manual

© 2020
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View
10’
20’
GK-2010 - 10’ x 20’ Display
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2020
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2020
Order #XXXXX
Assembly Assembly Cont’d
Stacking Unstacking
Stacking Assembly
1) Place one horizontal frame on top of the other, lining up the
center grooves.
2) Turn stacking lock clockwise to tighten into place. Repeat
for each lock.
Stacking Disassembly
1) Turn the stacking lock counter-clockwise to loosen.
2) The whole spring on the stacking lock should be in view to
release each frame. The disengaged spring should release
the stacking lock. If not, keep turning the stacking lock until
it disengages.
Side-by-Side Assembly
1) Frames: Place frames side-by-side with one higher than the
other, then slide panel down to lock panels securely together.
2) Corner Connectors: Repeat Step 1 for installing corner
connectors to frames.
Side-by-Side Disassembly
1) Pull pin lock outwards to disengage.
2) Pull frames upward and apart at the same time to detatch.
Push stacking lock into the slot
of the upper frame, then spin the
cap to tighten the lock.
Push pin lock into hole of connecting frame.
Note: Block of pin lock will secure in groove.
Disengage the stacking lock by
spinning the cap counter
clockwise and pulling down.
Cap
Stacking
Lock
Pin Lock
Top View
Corner Connector
SEG
Grooves
Note: Orientation of Corner
Connector may change.
Gravitee Assembly

© 2020
Order #XXXXX
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Installation

© 2020
Step 1 of 2
Order #XXXXX
Locked layer contains
placeholder marks.
Steps:
1) Assemble Gravitee Panels & Posts [1through 15]
together in numerical order as shown, then attach
EndCap [1A] to Panel [15].
See Gravitee Side-by-Side Assembly instructions
in the General Information pages.
Item
1
1A
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Qty.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
46”w x 95”h Gravitee Panel
95”h Gravitee EndCap
46”w x 95”h Gravitee Panel
94.5”h Gravitee Corner Post w/ caps
38”w x 95”h Gravitee Panel
94.5”h Gravitee Corner Post w/ caps
46”w x 95”h Gravitee Panel
46”w x 95”h Gravitee Panel
94.5”h Gravitee Corner Post w/ caps
38”w x 95”h Gravitee Panel w/ Door
94.5”h Gravitee Corner Post w/ caps
46”w x 95”h Gravitee Panel
46”w x 95”h Gravitee Panel
46”w x 95”h Gravitee Panel
95”h Gravitee Corner Post
38”w x 95”h Gravitee Panel
123
4
5
6
7
2A 2B
8
9
10
11
12
13
14
15
1A
(EndCap)
When assembled
Profile View
Profile View Profile View
Profile ViewProfile View
Backwall Assembly

© 2020
Step 2 of 2
Order #XXXXX
Locked layer contains
placeholder marks.
SEG Graphic Installation
Corner A
Corner D
Corner B
Corner C
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab. Gently pull up on
the tab to remove the fabric.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
Light Attachment
Attach lights to
Horizontal where
desired and
tighten in place.
*
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Attachment
*
Pin
Steps:
1) Install Door onto Panel [9]. See Door Attachment detail.
2) Apply SEG Graphics to back of Panels [1/2], front of panels [6/7]
& front of Panels [11/12/13], as shown.
3) Use Velcro to affix Sintra graphics to Panel [4], around
Door Panel [9] & to front & back of Panel [15].
4) Connect Lights to top of assembly as shown.
See Light Attachment detail.
**
S
EG
G
r
a
p
hic
Bac
k
SEG Graphic
1
9
11
12
13
15
2
4
6
7
**
S
i
n
t
r
a
Gr
a
p
h
ic
S
i
n
t
r
a
Gr
a
p
h
ic
D
o
o
r
S
i
n
t
r
a
Gr
a
p
h
ic
S
i
n
t
r
a
Gr
a
p
h
ic
*
*
S
EG
G
r
a
p
hic
Backwall Attachments