Classic Exhibits VISIONARY DESIGNS MOD-1372 Manual

© 2019
Order #XXXXX
Locked layer contains
placeholder marks.
BACK VIEW
BACK VIEWFRONT VIEW
Cord Management for iPad
Feed iPad cord through
top hole of post, then
out bottom hole of post.
Connect to power.
Cord
Access
iPad
Lock Lock
Foam Lining
Removed
Home Button Shield
Optional Cover for Home Button
1) Remove foam lining from inside bottom of clamshell.
2) Attach Home Button Shield with double-sided tape to
inside of clamshell, keeping top of shield flush with
clamshell opening.
NOTE: This is a permanent fix and can’t be easily removed.
Completed Assembly
Steps:
1) Install Base Plate to bottom of Kiosk, using bolts.
2) Attach Sintra Graphic to Kiosk, using screw caps.
3) Connect Shelf, using bolts from back side of Kiosk.
4) Attach iPad clamshell to top of Kiosk, as shown in detail.
5) Connect power cords to RGB LED lights on sides of Kiosk.
See opposite page for RGB Remote Controller instructions.
Graphic
screw
caps
hole for wire
management
screw
caps
screw
caps
bolt
Base
Plate
Kiosk
RGB LED Power Cord Attachment
Connect transformer to RGB LED Controller.
Then connect transformer to power source.
LED Controller
LED Lights
Transformer
*
connector
plate
spacer
bolt
T-nut
1) Attach Connector Plate & Spacer to top of kiosk
using bolt to t-nut connection.
2) Connect iPad clamshell to connector plate with hex nuts.
*** Connector Plate & Spacer stay attached to Kiosk. ***
iPad Clamshell Attachment
*
hex
nuts
Clamshell
Shelf
bolts
iPad
Clamshell
connector
plate
spacer
*
Velcro
Clamshell
Transformer
LED Lights
*
LED Lights
*
Door
Hole for wire
management
MOD-1372 iPad Kiosk
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2019
Order #XXXXX General Information
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
LADDERS OR LIFTS
MAY BE REQUIRED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
Controlling the RGB LED lights
Function of Keys
Receiver:
1. Working voltage: DC12V/24V
2. Output: Max. 6A/Channel
Total output Max. 10A
3. Max standby power: 0.5W
Remote Control:
1. Working voltage: 3V
2. Standby power: <20uA
3. Transmitting power: 6dBm
Specifications:
Static Mode:
1. Use the Color Ring key to select a color.
2. Saturation is controlled with W/R/G/B keys.
3. White mode is available by long-pressing ‘ON’ key.
4. Colors (not white) are dimmable with the
Brightness key.
Dynamic Mode:
Press "M" key to cycle through the following options:
1. White light fades in and out.
2. Several colors fade in and out.
3. R,G,B three colors fade in and out.
4. R,G,B three colors flash.
5. Six colors flash.
6. Random color flashes.
7. Red color fades in and flashes.
8. Green color fades in and flashes.
9. Blue color fades in and flashes.
To Pair a Remote with Multiple Units:
1. Power on the lights.
2. Press ‘ON’ key within 3 seconds.
3. Lights will blink when link is made.
To unpair: Long press ‘ON’ key within 3 seconds
after switching on lights.
Remotes can be paired with one or more receivers.
Different receivers can work synchronously even
when started at different times (within 30 min).
Master ON
Mode (M)
White +/-
Red +/- Green +/-
Blue +/-
Brightness - Brightness +
Color Ring
W R G B
ON
S- M S+
OFF
Indicator
Master OFF
Speed - Speed +