Classic Exhibits VISIONARY DESIGNS MOD-1204 User manual

www.classicexhibits.com
Step 1
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - MOD-1204 - Kiosk Assembly
Insert Size:
9.529”w x 23.331”h
Item Number
1
2
3
Description
Curve Panel
Curve Panel w/ Door
Curve Panel
Item
1
2
3
4
5
5a
6
Description
44.5”h Round Vertical Extrusion w/ Connector Attached
44.5”h Round Vertical Extrusion
44.5”h Round Vertical Extrusion w/ Connector Attached
44.5”h Round Vertical Extrusion
9.029”w Horizontal Extrusion
9.029”w Horizontal Extrusion
13”w Horizontal Extrusion
Qty.
1
1
1
1
4
1
2
Steps:
1) Attach upper extrusions to lower extrusions [2 to 1 and 4 to 3].
2) Attach (2) extrusions [5] between vertical assembly [1/2 and 3/4], placing insert
between horizontals as shown in illustration.
3) Assemble counter base by connecting panel #1to connect on vertical extrusion [1],
then continue in numerical order.
4) Velcro internal shelf supports to inside of assembled counter base.
5) Place internal shelf atop supports.
6) Attach remaining horizontal extrusions [5] between vertical assembly,
placing inserts where indicated.
7) Attach shelf supports [6] to vertical extrusion [2], then set shelves atop supports.
2
3
4
5
1
Insert Size:
9.529”w x 18.331”h
Insert Size:
9.529”w x 38.417”h
Internal Shelf
Counter Top
1
2
3
55
5a
5
6
6
Modul Extrusion Part List Euro LT Panel System Part List
Attach monitor brackets
to back of monitor.
Hook monitor brackets over top of wall
plate, then secure with safety bolts to
bottom of monitor brackets.
Modul
Extrusion
Monitor Mount Attachment
Insert connectors into groove of
extrusions.Then attach wall mount
to connectors using bolts provided.
Connector

www.classicexhibits.com
Step 2
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews
NOTE :
PDF copies of your Setup Instructions are available @ www.classicexhibits.com
Use the Search Tool located on the lower left-hand corner of the Classic Home page.
Enter your 5-7 digit Order #.
Search for Setup Instructions
search

www.classicexhibits.com
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
13”h Extrusion
Qty. : 2
9.029”h Extrusion
Qty. : 4
9.029”h Extrusion
Qty. : 1
9.529”w x 38.417.”h
Qty. : 1
9.529”w x18.331”h
Qty. : 1
9.529”w x 23.331”h
Qty. : 1
Additional Items:
_________________
__________________
44.5” Tapered Round Extrusion
Qty. : 4
Case 2 of 2
Case 1 of 2
Internal Shelf
Counter
Setup Hardware
Monitor Mount
(2) Shelves
I
N
S
E
R
T
I
N
S
E
R
T
I
N
S
E
R
T
Additional Items:
_________________
__________________
Oval Graphics
Curve Panel (2) Small Curve Panels
Case Packing Instruction - 1 Unit - Total 2 Cases

www.classicexhibits.com
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
13”h Extrusion
Qty. : 2
9.029”h Extrusion
Qty. : 4
9.029”h Extrusion
Qty. : 1
9.529”w x 38.417.”h
Qty. : 1
9.529”w x18.331”h
Qty. : 1
9.529”w x 23.331”h
Qty. : 1
Additional Items:
_________________
__________________
44.5” Tapered Round Extrusion
Qty. : 4
Case 2 of 2
Case 1 of 2
Internal Shelf
Counter
Setup Hardware
Monitor Mount
(2) Shelves
I
N
S
E
R
T
I
N
S
E
R
T
I
N
S
E
R
T
Additional Items:
_________________
__________________
Oval Graphics
Curve Panel (2) Small Curve Panels
Case Packing Instruction - 1 Unit - Total 2 Cases