Classic Exhibits Visionary Designs VK-2963 User manual

www.classicexhibits.com
Step 1
Page 1 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Plan View
10’
20’
General Layout

www.classicexhibits.com
Step 2
Page 2 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED

www.classicexhibits.com
Step 3
Page 3 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Case Packing
Counter
14
12
12
13
13
8
9
4523Base Plate
Wings
& Header
Base Plate
6 7
14
Counter

www.classicexhibits.com
Step 4
Page 4 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Case Packing
Counter
7,6,10,11
Shelf Supports
Infills
Shelf
Door Assembly Door Assembly
Case 2
Level 1 (Bottom Layer) Level 2 Level 3 Level 4 Level 5
Graphics
Lights
Setup Hardware

www.classicexhibits.com
Step 1
Page 1 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2962 Backwall Assembly
1A
1A
1A
1A
7
10
10a
11
6
4
5
9
8
2
3
7a
6a
4a
5a
9a
8a
2a
3a
Item
1A
2/2a
3/3a
4/4a
5/5a
6/6a
7/7a
8/8a
9/9a
10/10a
11
Qty.
4
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1
Description
Base Plates
39” Vertical extrusion
39” Vertical extrusion top left outside cut
39” Vertical extrusion
39” Vertical extrusion top right outside cut
41” Horizontal extrusion
41” Horizontal extrusion
41” Top left curved extrusion
41” Top right curved extrusion
28” Horizontal extrusion
28” Horizontal extrusion
Steps:
1) Attach base plates [1A] to lower verticals [2,2a,4 & 4a].
2) Connect upper verticals [3,3a,5 & 5a] with
connection bars [b] to lower verticals.
3) Connect horizontals [6 & 7] [6a & 7a] with connection bar [a].
4) Connect horizontals [10,10a & 11] between verticals.
5) Connect curved extrusions [8 & 9] [8a & 9a] with connectors [a].
6) Connect curved assemblies [8/9] [8a/9a] between verticals.
7) Attach Velcro Graphic to back of frame as shown.
Velcro:
Back/Top
Edge
Velcro:
Back/Top
Edge
Velcro:
Back/Top
Edge
Velcro:
Back/inside
Edge
Back View
Back View
Back View
Attach graphic
to velcro on back of
assembled frame
Turn Knob Clockwise
to Tighten Lock
indicates location of
knobs on BACKSIDE of unit.
Do not over tighten Knobs
Knob
Knob
indicates
location of connection
lock with knob.
Horizontal Placement
Stopper
Set upper horizontal
bar atop stopper where
indicated on verticals
Note: Slide connection
bar between extrusions and
tighten knobs to secure.
Connection Bar
b
a
b
b
b
a
a
a
Velcro:
Back/Top
Edge
Velcro:
Back/Top
Edge
Velcro:
Back/Top
Edge
Velcro:
Back/inside
Edge
Velcro:
Back/inside
Edge
Velcro:
Back/inside
Edge

www.classicexhibits.com
Step 2
Page 2 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2962 Backwall Attachments
Wing
Wing
Wing
Wing
Steps:
1) Attach Wings to A10’s as shown in Example of A10 Clamp Attachment detail.
2) Attach header graphic as shown in Graphic Attachment detail.
3) Connect lights as shown in Light Connection detail.
4) Connect monitors as shown in Monitor Mount Attachment details.
Light Connection
Attach light to
backwall where
desired and tighten
in place.
Graphic
Cap
Standoff
Barrel
Slide connector on back of standoff
barrels into groove of extrusion
and twist to secure in place. Secure graphic
to standoffs using screw caps.
Graphic Attachment
Header
Header
When desired location
is found, tighten
set screw to secure.
Slide connector on back
of A10 clamp into groove
of extrusion.
Example of A10 Clamp Attachment
Tighten knob to secure
shelf/wing in place.
Monitor Mount Attachment
Connectors
Attach monitor mount back
plate to connectors using
setscrews provided.
*
*
*
*
*
*
*
*
*
*
*
*
**
*
*
*
*
*
*
Attach wall plate to
horizontal bar using
bolts and wing nuts
Hook monitor brackets over
top of wall plate, then secure
with safety bolts to bottom
of monitor brackets.
Monitor Mount Attachment

www.classicexhibits.com
Step 3
Page 3 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Counter
Shelf
Shelf
16
17
17A 17A
18
16
18
Counter
When assembled
Counter Top Attachment
Insert screws located
on underside of counter
into holes on flange plate
and secure with wing nuts.
Wing Nut
Item
12
13
14
Qty.
2
2
2
Description
11.5” Horizontal Extrusion
26.75” Curved Extrusion
20.3” Curved Extrusion
Steps:
1) Attach Curved extrusions [13,14].
2) Attach horizontal extrusion [12] to [13/14].
3) Connect [12/13/14] to vertical extrusion as shown.
4) Attach hostess shelves [15] between backwall vertical
and curved vertical [13].
5) Screw in top plate to curved extrusion [13] as shown.
6) Connect counter top as shown in detail below.
7) Attach monitor mounts as shown in detail.
Note: Curved extrusion
[13] and horizontal [14]
stay assembled for
shipping and packing.
17
VK-2962 counter Assembly

www.classicexhibits.com
Step 4
Page 4 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Pedestal Assembly
Counter
Infill
Hinge
Infill
Infill
6
3
2
4
10
9
12
11
5
1
8
7Back Side
When assembled
Front Side
When assembled
Item
1-2
3-4
5
6-7
8
9
10-11
12
Qty.
1ea.
1ea.
1
1ea.
1
1
1ea.
1
Description
38” Vertical Extrusion w/ cut
38” Vertical Extrusion
18.9” Horizontal Extrusion
18” Horizontal Extrusion
20” Horizontal Extrusion
22.5” Curved Extrusion
18” Horizontal Extrusion
20” Horizontal Extrusion
Steps:
1) Attach lower horzontals [5,6,7,8] between
verticals [1,2,3,4] as shown.
2) Attach door using pins as shown in
Door Attachment detail.
3) Insert infills as shown.
4) Insert [9,10,11,12] between verticals.
5) Place internal shelf on top of shelf supports.
6) Place counter on top.
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
Hinge
Door
Shelf Supports
Shelf Supports
Shelf Supports
Shelf Supports