Classic Exhibits SUPERNOVA VK-2949D Manual

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Top View
10’
20’
Perspective View
VK-2949D General Layout
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq foot
Plan View

© 2023
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2023
Order #XXXXX CEI152 Frame Assembly
Straight Connection
Adjust connectors if necessary to
prevent gaps in connection.
Upper Horizontal Extrusion
Lower Horizontal Extrusion
COMPLETED ASSEMBLY
3) Tighten all knobs to secure connection.
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
When assembling frame, first attach all straight
connectors, then attach corner connectors.
1) Place extrusions end-to-end.
CEI152 Profile
Slide both connectors across seam of extrusions.
Tighten all knobs.
All knobs must be tightened securely to ensure a proper connection.
All knobs must be tightened securely to ensure a proper connection.
Corner
Connectors Corner
Connectors
Corner
Connectors Corner
Connectors
Straight Connector
Straight Connector
2) Loosen all knobs, then slide straight
connectors across the seam of extrusions.
Disassembly
1) Loosen all knobs.
2) Slide connectors off of one extrusion.
3) Tighten knobs to prevent loss during
packing & shipping.
Corner Connection
3) Tighten all knobs to secure connection.
Disassembly
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
Keep straight connectors in groove of
extrusion. Do not remove connectors
during disassembly.

© 2023
Order #XXXXX
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Installation

© 2023
Case 1 of 4
Order #XXXXX Case Packing
Locked layer contains
placeholder marks.
Setup Hardware
Top View of Each Level
Level 1
Base Plates
[1] (Qty. 2)
Level 2 Level 3
5 5A6 6A
7 7

© 2023
Case 2 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
Graphics
Level 1 Level 2
4A4 2A 3A 2 3
Case Packing

© 2023
Case 3 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
Setup Hardware
Level 1 Level 2 Level 3
55A6 6A
7 7
Level 1
Base Plates
[1] (Qty. 2)
Case Packing

© 2023
Case 4 of 4
Order #XXXXX Case Packing
Locked layer contains
placeholder marks.
Top View of Each Level
Graphics
Level 1 Level 2
4A4 2A 3A 2 3

© 2023
Step 1 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
5A
PR47
5A
Item
5A/5A
Qty.
1/1
Description
47.5” Vertical Extrusion w/ Miter One End
Steps:
1) Connect extrusions [5A] and [5A] together, using PR47
See PR47 Connector (Top View) detail.
PR47
Light
[5A]
[5A]
Place [5A] against [5A]. Slide PR47 into
recess in both CEI152 vertical extrusions.
PR47 Connector (Top View)
CEI152 Extrusion Assembly

© 2023
Step 2 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
Completed Left Backwall
Assembly
*
6
5
7
7
2
14
3
2A
4A
3A
6A
5A 5A
Item
1
2/2A
3/3A
4/4A
5/5A/5A
6/6A
7
Qty.
1
1/1
1/1
1/1
1/1/1
1/1
2
Description
Base Plate
38” Horizontal Extrusion w/ Miter One End
38” Horizontal Extrusion
38” Horizontal Extrusion w/ Miter One End
47.5” Vertical Extrusion w/ Miter One End
47.5” Vertical Extrusion w/ Miter One End
45.6767” Z33 Vertical Extrusion
Power
Break
Power
Break
Power
Break
Power
Break
to power
to power
*
Foot
Plate
Bolt
Bolt
Vertical
Extrusion
Horizontal
Extrusion
Washer
Wing Nut
Base Plate Attachment
Attach Base Plate to extrusions,
using bolts, washers, and wing nuts.
*
U-Bracket
Bolt
Bolt
Horizontal Extrusion
V4 V4
Slide V4 connectors into top groove of horizontal extrusion. Tighten
set-screws to secure. Connect U-Bracket to horizontal, using bolts.
Note: V4 connectors stay attached when packing.
U-Bracket Attachment
*
Steps:
1) Attach base plate [1] to extrusions [2] [5].
See Base Plate Attachment detail.
2) Attach U-Bracket to horizontal [3]. See
U-Bracket Attachment detail.
3) Assemble extrusions [2] thru [6A] together. See CEI-110
Fame Assembly sheet.
4) Attach vertical extrusion [7] between [3] and [3A].
5) Connect lights and transformers, then set transformers in
u-channel. See Light Connection details.
6) Install SEG graphic to front and blocker fabric to back of
assembled frame. See General Information sheet for
SEG Graphic Installation instruction.
++
+
-
-
-
Lights
Male
Male
Female
Female
to power Transformer
144W / 6A / 24V
Light to Light Connection
Light to Transformer Connection
Maximum of 11 light bars per transformer.
Left Backwall Assembly

© 2023
Step 3 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
Completed Right Backwall
Assembly
*
*
6A
4
1
4A 3A 2A
6
7
5A
5
7
Steps:
1) Attach base plates [1] to extrusions [2] [5].
See Base Plate Attachment detail.
2) Attach U-Bracket to horizontal [3]. See
U-Bracket Attachment detail.
3) Assemble extrusions [2] thru [6A] together. See CEI-110
Fame Assembly sheet.
4) Attach vertical extrusion [7] between [3] and [3A].
5) Connect lights and transformers, then set transformers in
u-channel. See Light Connection details.
6) Install SEG graphic to front and blocker fabric to back of
assembled frame. See General Information sheet for
SEG Graphic Installation instruction.
32
Item
1
2/2A
3/3A
4/4A
5
6/6A
7
Qty.
1
1/1
1/1
1/1
1
1/1
2
Description
Base Plate
38” Horizontal Extrusion w/ Miter One End
38” Horizontal Extrusion
38” Horizontal Extrusion w/ Miter One End
47.5” Vertical Extrusion w/ Miter One End
47.5” Vertical Extrusion w/ Miter One End
45.6767” Z33 Vertical Extrusion
to power
to power
Power
Break
Power
Break
Power
Break
Power
Break
++
+
-
-
-
Lights
Male
Male
Female
Female
to power Transformer
144W / 6A / 24V
Light to Light Connection
Light to Transformer Connection
Maximum of 11 light bars per transformer.
*
Foot
Plate
Bolt
Bolt
Vertical
Extrusion
Horizontal
Extrusion
Washer
Wing Nut
Base Plate Attachment
Attach Base Plate to extrusions,
using bolts, washers, and wing nuts.
*
U-Bracket
Bolt
Bolt
Horizontal Extrusion
V4 V4
Slide V4 connectors into top groove of horizontal extrusion. Tighten
set-screws to secure. Connect U-Bracket to horizontal, using bolts.
Note: V4 connectors stay attached when packing.
U-Bracket Attachment
Right Backwall Assembly

© 2023
Step 4 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
V4 V4
V4 V4
Completed Assembly
Left Backwall
Right Backwall
Steps:
1) Attach left and right backwalls together, using brackets, bolts and V4 connectors.
Note: V4 connectors stay attached when packing.
6” x 12” Bracket
Left to Right Backwall Assembly